JET Tools JWS-22CS Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools JWS-22CS manuals!
Problems with JET Tools JWS-22CS?
Ask a Question
Free JET Tools JWS-22CS manuals!
Problems with JET Tools JWS-22CS?
Ask a Question
Most Recent JET Tools JWS-22CS Questions
My 1\2' Router Bit Is Not Tight In The Col Let
my 1\2" router bit is not tight in the col let
my 1\2" router bit is not tight in the col let
(Posted by mimis5 3 years ago)
Popular JET Tools JWS-22CS Manual Pages
User Manual - Page 1
M-708320 Revision G3 11/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
JWS-22CS Spindle Shaper
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No.
User Manual - Page 2
... YOU.
The specifications listed in your area call 1-800-274-6846 or use and are given as expendable parts or accessories expected to Get Technical Support Please contact Technical Service by JPW Industries, Inc.
Motors; Pro-Duty Air Tools 2 Year - Metalworking Machinery; Woodworking Machinery used for industrial or commercial purposes 5 Year - Manual Hoists; Hand Tools
NOTE: JET is...
User Manual - Page 3
... ...7 Specifications ...7 Unpacking and Cleanup ...8 Adjustments ...9
Arbor Removal and Installation ...9 Collet Installation ...10 Fence Adjustments...10 Table Ring Removal and Installation...10 Operation ...11 Spindle Control...11 Using the Fence as a Guide ...11 Shaping with Collars and Starting Pin ...11 Collar Positioning ...12 Starting Pin...12 Lubrication ...13 Replacement Parts...15...
User Manual - Page 5
... face or dust masks that if precautions are specifically designed to determine that if precautions are : ...manual:
This means that are not heeded, it comes to persons. • NEVER STAND ON A MACHINE. Keep tools sharp and clean for alignment of moving parts, binding of moving parts, breakage of the machine, a guard or other part that is damaged should be properly repaired or replaced...
User Manual - Page 6
... run at 115 volt operation. The 115V attachment plug, supplied with the shaper, must be replaced with all local and national codes after the 230 volt plug is installed.
4. The shaper must comply with a UL/CSA listed plug suitable for proper procedures to install the plug. This machine must be properly grounded to help prevent electrical...
User Manual - Page 7
... for the complete line of dust collectors and the full line of JET Dust Collector Hoses and Accessories. See your new shaper if you require parts or service. Specifications
Model Number...JWS-22CS Stock Number ...708320 Cutterhead Speed(reversible)(RPM 7,000 & 9,000 RPM Table Size (in.) ...18-1/8 x 22-1/4 Table Slot (in.) ...3/4 x 3/8 T-slot Table Opening Diameter (in.) ...5-1/4 Insert...
User Manual - Page 8
...and melt plastic. Tools Required for shipping damage and report any damage or missing parts to the fence body with kerosene. Unpacking and Cleanup
1. Clean all contents from the shipping container. Install dust chute to..., paint thinner, or any shipping material until the shaper is set up and running.
2.
Finish removing all protected parts with
two 1/4" x 1/2" hex cap bolts.
8
User Manual - Page 9
...purposes only! Use the following procedure to lock the main spindle. 5. Adjustments
Arbor Removal and Installation
All adjustments to the machine must be made with a draw bar and a nut. Failure to... the latch (A, Fig.
1). Pull the spindle locking mandrel (A, Fig. 2) out,
and turn
to install the arbor. 1. The arbor is mounted to comply may result in serious injury. Open the door, and...
User Manual - Page 10
...7), adjusting the hold down to adjust fence in the spindle.
2. Table Ring Removal and Installation
To remove the table ring(s):
1. Remove any collet or spindle assembly in or out,... socket cap screws. Collet Installation
1. Lift ring.
5.
Loosen and remove the three 1/4" x 5/8" cross point screws from the power source.
2. To set up the shaper for height by loosening wing...
User Manual - Page 11
... be used when work 's edge must remain untouched by the cutter so that the collar will not be supported by the rear fence when both the front and rear fences are in line as a Guide
Shaping with collars and starting pin for an example of
the work (i.e. Using the Fence as shown...
User Manual - Page 12
... the work must be positioned above the cutter, Figure 17, offers the advantage of the work piece will not gouge the work will now be supported by advanced users! When using the guide pin as support, as shown in Figure 19.
User Manual - Page 14
...Shaper will not start up to support end of cut . Cord damaged.
Unlock spindle -
Feeding work against cutter.
Defective V-belt.
Variation of cut with the grain.
Replace ... proper gauge wire. Replace pulley. Troubleshooting
Trouble
Probable Cause
Remedy
Cord unplugged from the power source. Plug in the wrong direction.
Replace cord.
Reset overload ...
User Manual - Page 15
... uniform.
Use holddowns; On hardwoods take light cuts; Use hold-downs. Replacement Parts
Replacement parts are listed on one pass. Variation in raising mechanism. Cuts not smooth....Model Number and Serial Number of your machine available when you call 1800-274-6848, Monday through Friday (see our website for business hours, www.jettools.com).
To order parts or reach our service...
User Manual - Page 19
...Guide Plate ...2 81 JWS18HO-81 Slide Block ...2 82 JWS18HO-82 Guide Plate Support...Set Screw 1/4x3/8 1 50 JWS22CS-50 Washer 5/16x18 5 51 TS-0081031 Hex Cap Screw 5/16x3/4 2 52 JWS22CS-52 Motor Plate Bracket 1 53 VB-M23 V-Belt ...1 54 JWS22CS...JWS22CS-59-2 ......... Strain Relief 3 59-3 ...........JWS18HO-59-3......... Plastic Ball 1/4 4
19 Part No. Plate...1 60 JWS22CS...
User Manual - Page 20
... Complete (not shown 1 JWS22CS-AP Accessory Package 1 STRIPE-1-3/4 JET Stripe (not shown per ft.
** included in JWS22CS-HK, Hardware Kit
20 Stop Pin ...2 101 JWS18HO-101.......... Label (spindle direction 1 112 JWS22CS-112 .......... Miter Gauge Complete (includes # 25 thru 30 1 JWS22HO-HK Hardware Kit (shaper - Part No. I.D. Screw...1 108 JWS22CS-108 .......... Index No...
JET Tools JWS-22CS Reviews
We have not received any reviews for JET Tools yet.