Use and Care Guide
Page 1
... not avoided, could result in death or serious injury. [_kCAUTION] Caution indicates a potentially hazardous situation which of the tools, materials, and accessories you begin. f ® FOOD WASTE DISPOSERS Installation, Care & Use Manual TOOLS AND MATERIALS YOU WILL NEED: Slotted Screwdriver, Adjustable Pliers, Plumber's Putty, Electrical Tape TOOLS, MATERIALS, AND ACCESSORIES YOU MAY NEED: Phillips...
... not avoided, could result in death or serious injury. [_kCAUTION] Caution indicates a potentially hazardous situation which of the tools, materials, and accessories you begin. f ® FOOD WASTE DISPOSERS Installation, Care & Use Manual TOOLS AND MATERIALS YOU WILL NEED: Slotted Screwdriver, Adjustable Pliers, Plumber's Putty, Electrical Tape TOOLS, MATERIALS, AND ACCESSORIES YOU MAY NEED: Phillips...
Use and Care Guide
Page 2
II Model A B C 601016012 11 3/8" 6" 4' 6011/6013 12 5/8" 6" 4" 60552 12 5/80 6" 4" 60581/60554 12 3/4" 6 11/16 = 4" 60691/60556 12 3/4 = 6 1t/16 m 4" 60559* 15 7/8 = ...4-1). 3. If this is corroded or too tight, apply penetrating lubricant,) 4. @) CHECK INSTALLATION DIMENSIONS A: Disposer Height B: Distance from bottom of sink bowl to centerline of discharge B outlet. (Add ... mounting ring over sink flange so it (see Figure 2-1). 9 2. Loosen nut (B) at waste pipe entering wall (Dimension "F" must be greater than 1/4" to prevent scratching.) Reference Figure 5-1...
II Model A B C 601016012 11 3/8" 6" 4' 6011/6013 12 5/8" 6" 4" 60552 12 5/80 6" 4" 60581/60554 12 3/4" 6 11/16 = 4" 60691/60556 12 3/4 = 6 1t/16 m 4" 60559* 15 7/8 = ...4-1). 3. If this is corroded or too tight, apply penetrating lubricant,) 4. @) CHECK INSTALLATION DIMENSIONS A: Disposer Height B: Distance from bottom of sink bowl to centerline of discharge B outlet. (Add ... mounting ring over sink flange so it (see Figure 2-1). 9 2. Loosen nut (B) at waste pipe entering wall (Dimension "F" must be greater than 1/4" to prevent scratching.) Reference Figure 5-1...
Use and Care Guide
Page 3
...clear all old putty from electrical supply wires. Disconnect drain trap from disposer (Instruction 3) and go to replace I from disposer waste discharge tube with screwdriver, and remove old mounting assembly (see Fig.... 6-1). (Also disconnect dishwasher drain connection, if required.) 3. Loosen three mounting screws, pry snap ring off with adjustable pliers (see Figure 6-5). (Some mounting assembly removal requires additional tools.) 6. Remove P-trap. 2. Follow the installation...
...clear all old putty from electrical supply wires. Disconnect drain trap from disposer (Instruction 3) and go to replace I from disposer waste discharge tube with screwdriver, and remove old mounting assembly (see Fig.... 6-1). (Also disconnect dishwasher drain connection, if required.) 3. Loosen three mounting screws, pry snap ring off with adjustable pliers (see Figure 6-5). (Some mounting assembly removal requires additional tools.) 6. Remove P-trap. 2. Follow the installation...
Use and Care Guide
Page 4
...installing or servicing dis- Once the circuit you are installed. Grounding Instructions for all ungrounded supply conductors) installed within sight of the disposer sink opening and secure the electrical plate (C) (see Figure 9-1). This appliance is properly grounded. Remove electrical cover plate from Kenmore... main service panel until disposer is equipped with wire nuts (see Figure 9-1). 9-1 Grounding Instructions for electric current to disconnect all models listed in the electrical cover plate opening (1 HP minimum rating). Strip wires back approximately 1/2 ...
...installing or servicing dis- Once the circuit you are installed. Grounding Instructions for all ungrounded supply conductors) installed within sight of the disposer sink opening and secure the electrical plate (C) (see Figure 9-1). This appliance is properly grounded. Remove electrical cover plate from Kenmore... main service panel until disposer is equipped with wire nuts (see Figure 9-1). 9-1 Grounding Instructions for electric current to disconnect all models listed in the electrical cover plate opening (1 HP minimum rating). Strip wires back approximately 1/2 ...
Use and Care Guide
Page 5
... (reference Figure 11-2). they may be used . Two-Bolt DlechargeTube Installation (PreferredTwo-Bolt Installation) if replacing existing disposer, remove and discard existing discharge tube and gasket. (Unit will now hang by itself. 1ATTACH DISCHARGE TUBE TO WASTE DRAIN LINE Determine appropriate installation based upon new installation or plumbing configuration: TwoBolt Discharge Tube or One-Bolt Discharge...
... (reference Figure 11-2). they may be used . Two-Bolt DlechargeTube Installation (PreferredTwo-Bolt Installation) if replacing existing disposer, remove and discard existing discharge tube and gasket. (Unit will now hang by itself. 1ATTACH DISCHARGE TUBE TO WASTE DRAIN LINE Determine appropriate installation based upon new installation or plumbing configuration: TwoBolt Discharge Tube or One-Bolt Discharge...
Use and Care Guide
Page 6
... and/or dishwasher contamination.) Ensure knockout plug is required when an food waste; Detach perforated portion of injury, close supervision is removed (see Instruction 1). I_ jA I I Figure12-1 The disposer installation is magnetically • Replace anti-splash baffle when worn to remove objects from a waste disposer use nonmagnetic tools. Read ALL SAFETY INSTRUCTIONS on , and check under...
... and/or dishwasher contamination.) Ensure knockout plug is required when an food waste; Detach perforated portion of injury, close supervision is removed (see Instruction 1). I_ jA I I Figure12-1 The disposer installation is magnetically • Replace anti-splash baffle when worn to remove objects from a waste disposer use nonmagnetic tools. Read ALL SAFETY INSTRUCTIONS on , and check under...
Use and Care Guide
Page 7
... is created by the particles inside the grind chamber. • Grind peelings from continuous feed models in the Installation, Care & Use manual. 2. Reach into disposer and position stopper to avoid possible drain blockage. First turn on /off and run water for at sametime to...pack chamber with scouringpad. 3. Place stopper back in the trash. A scouring action is normal. Remove wrenchette. 3. Slowly insert food waste into the disposer with tongs and remove object(s). Read important safety instructions contained in that the batch feed on a moderate to strong flow of ...
... is created by the particles inside the grind chamber. • Grind peelings from continuous feed models in the Installation, Care & Use manual. 2. Reach into disposer and position stopper to avoid possible drain blockage. First turn on /off and run water for at sametime to...pack chamber with scouringpad. 3. Place stopper back in the trash. A scouring action is normal. Remove wrenchette. 3. Slowly insert food waste into the disposer with tongs and remove object(s). Read important safety instructions contained in that the batch feed on a moderate to strong flow of ...