Kenwood KAC-6202 Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood KAC-6202 manuals!
Problems with Kenwood KAC-6202?
Ask a Question
Free Kenwood KAC-6202 manuals!
Problems with Kenwood KAC-6202?
Ask a Question
Most Recent Kenwood KAC-6202 Questions
Giving The Input ''music'' To My Amplifier, No Rca Cables (speaker To Amp)
Hi,I am installing a subwoofer in my 2014 Chevy Tahoe. I have no RCA cable to plug from my radio to ...
Hi,I am installing a subwoofer in my 2014 Chevy Tahoe. I have no RCA cable to plug from my radio to ...
(Posted by guillaumelongtin 8 years ago)
Popular Kenwood KAC-6202 Manual Pages
Instruction Manual - Page 1
STEREO/BRIDGEABLE POWER AMPLIFIER
KAC-6202
INSTRUCTION MANUAL
© B64-3043-00/00 (MV)
Instruction Manual - Page 2
...surface of water splashing. • When replacing a fuse, only use a new ...your Kenwood dealer. • Do not touch the unit during installation, consult your Kenwood dealer...problems during use automotive-grade wires or other wires with a hard cloth or a cloth dampened by volatile solvents such as coins or metal tools) inside the unit. • If the unit starts to page 5)
Accessories
Part...
Instruction Manual - Page 3
... and hits a person or safety part, it will become hot during use. Once installed, do not place any object on the opposite side such as the brake lamps, turn signal lamps and windshield wipers operate normally. English 3
If the unit comes off due to easily dissipate. Install the amplifier in a place where
people, resins...
Instruction Manual - Page 4
... power output of the genuineaccessory car stereo. NOTE
For the pre-output level or the maximum power output, refer to the in the instruction manual of the center unit.
4 OPERATION switch This switch is not output.)
4 English Use the diagram on the right as a stereo amplifier.
• MONO (Lch) position: Amplifies the signal input from...
Instruction Manual - Page 5
...light when the power is not connected to a metal part serving as an electrical ground passing electricity to the speaker output. • When the internal temperature is high and unit won't operate. • When a ground wire of trouble...the Power indicator goes off and the amplifier stops operating. • When a ...is turned on , the Power indicator lights. English 5 Check whether there is...
Instruction Manual - Page 6
... the ground lead to this terminal.
# Speaker level input terminals
NOTE
• The genuine-accessory car stereo shall have a maximum power output of no less than 40 W.
• Do not connect the speaker output leads from a power amplifier (Optional) to the speaker level input terminals of 2Ω or greater. Otherwise malfunction may...
Instruction Manual - Page 7
... shorts, then replace the fuse with a diameter of 5 mm² (AWG 10) or greater.)
• When more than one set of speakers are touching the car body. Remove the ignition key and disconnect the
negative - Set the unit according to the amplifier.
4Ω
4Ω 8 Ω
4Ω 4Ω 2 Ω
Combined impedance
English 7 ■ Installation procedure
Since there...
Instruction Manual - Page 8
... connector
Left
White
White/Black
Right
Gray
#
Gray/Black
Power control wire (Blue/ White)
@
GND
RCA cable ground terminal Speaker level input cable
Genuine-accessory car stereo (No line output center unit etc...
Instruction Manual - Page 9
■ Speaker wire connection (Stereo Connections) 00
Lead terminal*
(Bridged Connections) 0
25
* Commercially available parts Left speaker Right speaker
Speaker (Bridged)
25
■ Power wire connection
25
Terminal cover
789
Power control wire Battery wire*
Ground wire*
Protective Fuse*
Battery
Lead terminal*
English 9
Instruction Manual - Page 11
... should be as close as possible to 5.3 (mH).
2CAUTION
• If you wish to bridge-connect a speaker, the speaker impedance must be passed. Failure to set a crossover frequency of 120 Hz using a coil and capacitor...in a drop of the combined impedance with the closest ratings to the results calculated from the...
Instruction Manual - Page 12
...car body.
The sound quality is bad. • The speakers wire are
• Connect the input (or output)
(No sound from one side.) disconnected. Before calling service, first check the following table for possible problems.
PROBLEM... set improperly. • Set switches properly by referring to . Troubleshooting Guide
What might appear to
.
• Volume is too high.
• Replace the...
Instruction Manual - Page 13
...(4 Ω) (1 kHz, 0.8 % THD)...200 W x 1 Frequency Response (+0, -3 dB) ...10 Hz - 45 kHz Sensitivity (rated output) (MAX.) ...0.2 V Sensitivity (rated output) (MIN.) ...5.0 V Signal to change without notice. Specifications
Specifications subject to Noise Ratio...100 dB Input Impedance...10 kΩ Low Pass Filter Frequency (12 dB/oct.) ...50 - 200 Hz (variable) High Pass Filter Frequency (...
Kenwood KAC-6202 Reviews
Kenwood has a rating of 5.00 based upon 1 review.
Get much more information including the actual reviews and ratings that combined to make up the overall score listed above. Our reviewers
have graded the Kenwood KAC-6202 based upon the following criteria:
- Durability [1 rating]
- Cost Effective [1 rating]
- Quality [1 rating]
- Operate as Advertised [1 rating]
- Customer Service [1 rating]