Kenwood NX-340V Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood NX-340V manuals!
Problems with Kenwood NX-340V?
Ask a Question
Free Kenwood NX-340V manuals!
Problems with Kenwood NX-340V?
Ask a Question
Popular Kenwood NX-340V Manual Pages
Operation Manual 2 - Page 3
... NX-340 NX-340U
INSTRUCTION MANUAL
The AMBE+2TM voice coding Technology embodied in this product is explicitly prohibited from attempting to and ownership of Digital Voice Systems, Inc.
Patent Nos. #5,826,222, #5,754,974, #5,701,390, and #5,715,365. Firmware Copyrights The title to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in KENWOOD...
Operation Manual 2 - Page 4
...to qualified technicians only. No. THANK YOU
We are grateful you have chosen KENWOOD for the Speaker/ Microphone jacks.
NOTICES TO THE USER
◆ Government law prohibits the ... is important that the operator is punishable by fine and/or imprisonment. ◆ Refer service to the chassis ground. Terminal Descriptions
Speaker/ Microphone Jacks
It is mounted on the rear side ...
Operation Manual 2 - Page 5
... and found to comply with the instructions, may cause harmful interference to Part 15 of the FCC Rules. If... generate radio frequency energy and, if not installed and used in a particular installation. i This equipment generates, uses and can...reasonable protection against harmful interference in the instruction manual. These limits are designed to operate this equipment may cause ...
Operation Manual 2 - Page 6
... environment and conserve our natural resources.
KENWOOD's involvement in some areas. Pay attention to the volume level when turning the squelch off before installing optional accessories.
• The charger...fied by KENWOOD.
• If the die-cast chassis or other transceiver part is damaged, do not touch the damaged parts.
• If a headset or headphone is part of the antenna ...
Operation Manual 2 - Page 7
...to send an electric shock through the earphone and to your KENWOOD dealer. • Use of the transceiver while you use ... strike the driver or passengers. • Do not transmit while touching the antenna terminal or if any metallic parts are posted ... service stations. • Near explosives or blasting sites. • In aircraft. (Any use of the transceiver must follow the instructions
and...
Operation Manual 2 - Page 11
... microphone locking bracket 1 • Belt clip (KBH-10 1 • Screw (M3 x 8 mm 2 • Channel stopper 1 • Instruction manual 1 Note: Refer to "PREPARATION" starting on page 2 for accessory installation instructions.
1 CONTENTS
UNPACKING AND CHECKING EQUIPMENT 1 PREPARATION 2 ORIENTATION 7 PROGRAMMABLE AUXILIARY FUNCTIONS 8 BASIC OPERATIONS 11 VOICE OPERATED TRANSMISSION (VOX...
Operation Manual 2 - Page 18
Your dealer may have set some keys to activate a function is turned OFF and then ON again, the Key Lock function will sound. When making ... hold down the PTT switch and speak into the microphone to transmit.
■ CW Message 2 Press to transmit the preset Morse code message on your dealer for details on which keys need to be held down the key, the calling alert tone will be held ...
Operation Manual 2 - Page 19
... the Priority channel.
■ Scan Press to start (or stop) scanning the transceiver channels.
■ Scan Temporary Delete
9 Press this key in normal mode to set the current channel as Key Lock except that when the transceiver power is turned OFF and then ON again, the keys remains locked.
■ Lone...
Operation Manual 2 - Page 21
... step 2 for Channel selector positions 2 ~ 4. • If there are less than 4 password digits, repeat for only the number of digits the password contains.
4 Press the PTT switch to switch the transceiver ON. Enter the password (up to 4 digits) using the following procedure. 1 Set the Channel selector to position "1". 2 Press the Side 1 or Side 2 key...
Operation Manual 2 - Page 22
...For best sound quality, hold the transceiver approximately
1.5 inches (3 ~ 4 cm) from listening to code your transceiver settings. RECEIVING
Select the desired zone and channel. Refer to check whether or not the channel is ...free. • If the channel is programmed with settings for details.
12 This will prevent you will hear a call only if the received ...
Operation Manual 2 - Page 23
... blue *
Receiving an encoded call (FleetSync signaling, etc.)
Blinks red/orange
The selected channel has not been programmed and cannot be used.
* Your dealer can set the LED to blink either orange or blue for FleetSync, DTMF, 2-tone, or NXDN operation.
* Lights orange in Analog mode. * Lights blue in Digital mode...
Operation Manual 2 - Page 24
...first be turned off for 20 seconds, the transceiver will be unable to enter VOX setup mode.
◆ If a headset is connected to the transceiver while the VOX function is switched...be used if you are using a supported headset. VOX can be activated by your dealer, and can change this setting for each channel by your dealer. To activate VOX and set the VOX Gain level, perform the ...
Operation Manual 2 - Page 25
...data communications, including individual and group voice communications, Status calls, and GPS data transmission, are set the duration for the NXDN wireless communication protocol which uses 4 Level FSK. When you can ... timer expires before sending the status call and the received group ID matches the ID set up with ID list numbers by your dealer.
To make an Individual or Group call...
Operation Manual 2 - Page 26
...may flash green when receiving a QT/DQT signal which does not match the QT/DQT tone/code set up in use.
Note: Ask your dealer (default is present and no signal is 1 minute), transmission ...or an operation is released and the LED indicator blinks red when the battery needs recharged or replaced.
To stop the tone. LOW BATTERY WARNING
While operating the transceiver, the Low Battery Warning ...
Operation Manual 2 - Page 27
...transmit over the current signal: 1 Press and hold the PTT switch.
• If the channel is set up with ID, and "Wild Card" Group Calling.
17 When a channel is already in analog operation.... PTT ID
PTT ID is the transceiver unique ID code which is sent each time the PTT switch is included for digital radio communications. If a call containing...
Kenwood NX-340V Reviews
We have not received any reviews for Kenwood yet.