LevelOne IES-0920 Support and Manuals
Get Help and Manuals for this LevelOne item
View All Support Options Below
Free LevelOne IES-0920 manuals!
Problems with LevelOne IES-0920?
Ask a Question
Free LevelOne IES-0920 manuals!
Problems with LevelOne IES-0920?
Ask a Question
Popular LevelOne IES-0920 Manual Pages
Datasheet - Page 1
... exibility of 9 Ethernet ports that deal with no single failure. Supports 10/100Mbps-Full/Half-duplex, Auto-Negotiation, Auto-MDI/MDIX -... panel mounting - IES-0920
8 FE + 1 MM SC Unmanaged Switch -40 to 75, DIN-rail
Overview
LevelOne IES-0920 Industry Ethernet Switch provides... mounted on and o 6,000 times while loaded, with no setup or con gure required, truly plug and play. Alarms for ...
Manual - Page 1
IES-0920
8 FE + 1 MM SC Unmanaged Switch -40 to 75, DIN-rail
User Manual
v1.00 - 1206
Manual - Page 2
... the Industrial Ethernet Switch. This switch integrates full wire speed switching technology. In this manual, you will find:
· Features on the switch · Illustrative LED functions · Installation instructions · Specifications
IES-0920 User Manual
Page 1
To get the most out of this manual, you should have an understanding of Ethernet networking concepts. Preface
This...
Manual - Page 5
... -40℃ to 75℃ (-40℉ to 167℉) operating temperature range.
IES-0920 User Manual
Page 4 Power consumption: 9.12W Max. · Power Supply: Redundant DC Terminal Block power... Air Temperature @ 74℃ (165℉). · Supports DIN-Rail or Panel Mounting installation. Auto MDI/MDIX. · Supports 2048 MAC addresses. · Provides 768K bits memory buffer....
Manual - Page 7
Physical Ports
This switch provides: Eight 10/100Base-TX ports Eight 10/100Base-TX ports + one 100Base-FX/BX port Six 10/100Base-TX ports + two 100Base-FX/BX ports Four 10/100Base-TX ports + four 100Base-FX/BX ports
Connectivity RJ-45 connectors SC or ST connector on 100Base-FX fiber port SC connector on 100Base-BX fiber port
IES-0920 User Manual
Page 6
Manual - Page 8
Specifically, the site you should place the switch where it will not be subjected to 75 degrees Celsius...side of the switch · The power outlet should be within 1.8 meters of the switch. IES-0920 User Manual
Page 7
Installation
This chapter gives step-by-step instructions about how to install the switch:
Selecting a Site for the Switch
As with any electric device, you select should ...
Manual - Page 9
Push the front of the switch. Removal: Pull out the lower edge and then remove the switch from above using the slot. IES-0920 User Manual
Page 8 Installation: Place the switch on the DIN rail from the DIN rail. DIN Rail Mounting
Fix the DIN rail attachment plate to the back panel of the switch toward the mounting surface until it audibly snaps into place.
Manual - Page 10
... 2. Field Wiring Terminal: Use Copper Conductors Only, 60/75℃, 12-24 AWG torque value 7 lb-in case either PWR1 or PWR2 is enabled)
IES-0920 User Manual
Page 9 Connecting to Power
Redundant DC Terminal Block Power Inputs or 12VDC DC Jack (Optional)
Redundant DC Terminal Block Power Inputs
There are two pairs...
Manual - Page 11
... adapter to DC power adapter and attach the plug into a standard AC outlet with the appropriate AC voltage. The relay contact close if power falls
IES-0920 User Manual
Page 10 Step 2: Connect the power cord to the AC to the receptacle on the topside of the switch.
Manual - Page 12
IES-0920 User Manual
Page 11
Alarms for Power and Port Failure
Step 1: There are two pins on the terminal block are used for power failure detection. This DIP ...
Manual - Page 13
...Step 5: Once the connections between two end devices are turned off before any installation.
Step 3: Consult the previous section for each type of port in use. Cable Specifications
Speed
Connector
10Base-T 100Base-TX 1000Base-T 100Base-FX 100Base-FX 100Base-BX ... corresponding connectors for cabling requirements based on the power and the switch is off . IES-0920 User Manual
Page 12
Manual - Page 14
Specifications
Ethernet Switch
Applicable Standards
Switching Method Forwarding Rate 10Base-T:... location: Class I, Division 2 group A, B, C & D UL60950-1, EN60950-1, IEC60950-1 FCC Part 15, Class A EN61000-6-3: EN55022, EN61000-3-2, EN61000-3-3
IES-0920 User Manual
Page 13 Current Consumption Power Consumption Operating Temperature
Storage Temperature Humidity Safety
EMI
10/100Base-TX auto-...
Manual - Page 15
... Standards) Environmental Test Compliance IEC60068-2-6 Fc (Vibration Resistance) IEC60068-2-27 Ea (Shock) IEC60068-2-32 Ed (Free Fall) NEMA TS1/2 Environmental requirements for traffic control equipment
IES-0920 User Manual
Page 14
Manual - Page 16
... +
4
NC
5
NC
6
Input Receive Data -
7
NC
8
NC
Uplink Port Input Receive Data + Input Receive Data Output Transmit Data + NC NC Output Transmit Data NC NC
IES-0920 User Manual
Page 15
Appendix A -
Quick Install Guide - Page 1
...
Supports 2048 MAC ...setup or configure required, truly plug and play.
o WARNING - Do not disconnect equipment unless power has been removed or the area is suitable for Class I , Division 2, Groups A, B, C and D OR non-hazardous locations only. o WARNING - IES-0920...IES-0920 Quick Installation Guide CD User Manual
IES-0920
Page 2
Overview
LevelOne IES-0920...
LevelOne IES-0920 Reviews
We have not received any reviews for LevelOne yet.