LiftMaster SL575 Support and Manuals
Get Help and Manuals for this LiftMaster item
View All Support Options Below
Free LiftMaster SL575 manuals!
Problems with LiftMaster SL575?
Ask a Question
Free LiftMaster SL575 manuals!
Problems with LiftMaster SL575?
Ask a Question
Most Recent LiftMaster SL575 Questions
Motor
Motor run in open direction, but toclose you have to push it to get it to run. Have changed the star...
Motor run in open direction, but toclose you have to push it to get it to run. Have changed the star...
(Posted by sjrjames 9 years ago)
Operation
we Have a liftmaster sl575 that was originaly set up to operate both with a remote and a three butto...
we Have a liftmaster sl575 that was originaly set up to operate both with a remote and a three butto...
(Posted by pjokonski 9 years ago)
How To Change Operator From 115 Volt To A 230 Volt
(Posted by bmfhbill 10 years ago)
Set Operation Hours
How to set the gate operator to not open past 10pm ?
How to set the gate operator to not open past 10pm ?
(Posted by storage1metamora 11 years ago)
I Have 1 Lift Master Model Sl575 , I Need The Battery Backup ,can You Help Me,tk
(Posted by honoriofamma 12 years ago)
Popular LiftMaster SL575 Manual Pages
SL575 Manual - Page 2
... for factory supplied parts. Read them .
CARTON INVENTORY
Before beginning your gate and/or the gate operator if you see this manual and follow all components were supplied and received undamaged. TABLE OF CONTENTS
OPERATOR SPECIFICATIONS
Carton Inventory 2 Operator Dimensions & Horsepower Chart 3 UL325 Model Classifications 4
OPERATOR WARNINGS
• These instructions are not...
SL575 Manual - Page 5
... application.
2. Gate operating system designers, installers and users must be located on each side of the reset control shall not cause the operator to operate the controls. The operator is specifically designed for the construction and the usage class of a swing gate. For a gate operator utilizing a contact sensor such as a component part of the gate operator.
8 Controls...
SL575 Manual - Page 7
... a moving parts of the
gate.
Adjusted or Serviced
They cannot retract their arm and it gets caught between the top or bottom of the gate and the gate roller.
To prevent INJURY to prevent access through openings in the grill while the gate is intended for vehicular use separate entrance
Do not let children operate the gate or play...
SL575 Manual - Page 11
... (5.1 cm) U-bolts
AVERTISSEMENT 3.
ATTENTION
6. Figure 1
WARNING
"Outside" Gate
"Inside"
WARNING
1.
Thread the chain through the plastic chain guide, around Figure 2 drive and idler sprockets, and then through plastic guides
Safety Bracket
11 INSTALL GATE BRACWKEAT &RDNRIIVNE CGHAIN
CAUTION
To prevent damage to the operator or gate, DO NOT drive the limit (nuts) actuators on...
SL575 Manual - Page 13
... open limit, the gate will stop .
7. Manually close the gate to its full open the gate to gauge the correct distance.) Adjust with vertical screws.
The sensor must be centered over the magnet wheel. When power is built into both nuts.
4. The gate should be used to its full closed position.
13 If the operator fails to the troubleshooting section.
5. Adjust open...
SL575 Manual - Page 14
... Section on page 15. Obstruction While Closing (Edge/Photo Eye Input) Edge Input: See Programming Section on page 15.
On most operators this will be disabled until another command is opening gate to -Close. Activating this input when the gate is closing will have no effect. Activating this input when the gate is closing will have no effect. SECONDARY ENTRAPMENT...
SL575 Manual - Page 15
... (S2-4) selects edge or photo sensor for the gate opening cycle. MAG
WARN
PHOTO CLOSE
S2 ON
ON 1 2 34
PH
OPED
PH
CLED
NOTE: Timer-to -Close
Force Adjustment
Dip Switch (S2) Dip Switch (S1) Diagnostic LED
Connector (J2) Connector SAMS (J5)
Relay Drive Troubleshooting LEDs (D6) Terminal Troubleshooting LEDs (D11)
15
Limit LEDs Motor Learn...
SL575 Manual - Page 16
....
SL = Slide • SW = Swing
TTC
SW
TIMER-TO-CLOSE
SWING GATE S1
ON ON
1 2 34
RT
SAVE
LT
SL
RIGHT/LEFT OPERATION
This switch selects the gate opening direction, to the left or to optimize gate behavior for specific application.
PROGRAM SETTINGS (DIP SWITCH S1)
NOTE: For all settings into memory and locks out changes. The Timer-to movement...
SL575 Manual - Page 18
... block R4) to 15 rolling code
remote controls or passwords in use.
ATTENTION When changing from a
moving gate or door. Use of constant closure is factory set at terminals R1 and R2 located on the side of the Soft Open feature, perform the following instructions are no obstructions to
• ALWAYS keep remote controls out of reach of...
SL575 Manual - Page 19
.../Reset Button
19 All remote codes are intended for changing the code setting or replacing the battery.
THERE ARE NO OTHER USER SERVICEABLE PARTS. Accessories that all Stop/Reset controls are prohibited, except for use as a Stop/Reset command and is to be used to terminals 3 and 5 on the control box on the operator.
Soft Open These terminals are...
SL575 Manual - Page 20
... and the S4 switch programmed, both units must be used on (S4) switch setting. A momentary activation of the open limit. Terminals 4 & 5 (Com) - Close Override Control Input These terminals are seen when +24Vdc is applied to close stop if there is installed within line of sight of no further communications will cause the gate to open control of a 3-button...
SL575 Manual - Page 22
... board to close followed by two gates installed in how you are planning to access the SAMS system will close the barrier gate after the vehicle has passed through the SAM system. Attach a wire from the vehicle, the swing or slide gate.
2. Attach a wire from terminal 8 of the SL575 accessory wiring terminal block to the normally open (NO...
SL575 Manual - Page 26
.... If the green LED is a jumper across the master/second communication line.
➤ Review program settings page 19 and check both primary and secondary power is good, check to make sure that the communication wiring between breaker and operator by consulting the wiring specifications section on page 8 of the control board next to the...
SL575 Manual - Page 27
... BUT GATE DOES NOT MOVE; The unit's manual release, when engaged, will set so that the gate will run smoothly normally and reverse when encountering an obstruction.
➤ Disengage the manual release and roll gate open and close obstruction input has been programmed to move or binds, repair the gate.
➤ Adjust the clutch so that the operator can move the gate throughout...
SL575 Manual - Page 40
... SUCH PERIOD. HOW TO ORDER REPAIR PARTS
OUR LARGE SERVICE ORGANIZATION SPANS AMERICA
FOR INSTALLATION AND SERVICE INFORMATION, CALL OUR TOLL FREE NUMBER 1-800-528-2806 www.liftmaster.com
WHEN ORDERING REPAIR PARTS PLEASE SUPPLY THE FOLLOWING INFORMATION: PART NUMBER DESCRIPTION MODEL NUMBER
ADDRESS ORDER TO:
THE CHAMBERLAIN GROUP, INC.
Technical Support Group 6050 Country Club Road Tucson...
LiftMaster SL575 Reviews
We have not received any reviews for LiftMaster yet.