Mackie S-8 Support and Manuals
Get Help and Manuals for this Mackie item
Popular Mackie S-8 Manual Pages
Spec Sheet - Page 1
...DRIVER
WOOF
65
FUSE
POWER AC SELECT 115V ↔ 230V
7
10
+ HI VDC - Appendix C: S•8 Specifications..., polypropylene cone woofer
High Frequency: Wave guide loaded 1 in/25 mm silk dome tweeter...VAC: T 800 mA H/250 V
Power Consumption: 80 watts with music, loud mix
20 watts quiescent (idle...specifications at any time without notice.
POWER LED
-HI VDC
TAPCO S•8 BLOCK DIAGRAM 10....
Owners Manual - Page 2
... instructions should not attempt to the Tapco Service Department...serviced only by items placed upon or against potentially dangerous exposure to high sound pressure levels, it is in excess of the limits set out in installation such as marked on a bed, sofa, rug, or similar surface that its location
or position does not interfere with an extension cord, receptacle or other instructions...
Owners Manual - Page 3
... 10 Appendix A: Service Information 11 Appendix B: Connections 13 Appendix C: Specifications 14 TAPCO LIMITED WARRANTY 15
Don't forget to write your product information here for directions when lost, but we hope you read the rest of purchase:
Part No. 0008404 Rev.
Your new TAPCO® S•8 monitors are designed to read a manual? Product Serial #:
Speaker...
Owners Manual - Page 4
...loudness from the speakers gets really loud, really fast, try setting the LOW FREQ equalization switch to the +2 dB position to...Extremely Important Note on the rear panel all the S•8 studio monitors in your mixer (or other end into an AC outlet ... jack on your monitor speakers quickly. Slowly turn up your mixer down and read the rest of this manual...especially the following ...
Owners Manual - Page 5
... SERVICEABLE PARTS INSIDE. Please see the Safety Instructions on hearing protection.
• When you bought them someday. You may decide that boosting the high frequencies in the monitors can result in a duller mix, while reducing the high frequencies can result in the frequencies above 5 kHz.
S•8 ACTIVE STUDIO MONITOR
INPUTS
RCA (UNBALANCED)
XLR (BALANCED)
SETTINGS HIGH...
Owners Manual - Page 6
... damping factor of the amplifier isn't compromised by Mackie® family, joining its sibling, the TAPCO S•5. The TAPCO S•8 is minimal. There are many benefits to integrating an active crossover, power amplifiers, and drivers into the S•8 Studio Monitors:
• Flat frequency response (±3 dB, 40 Hz to 20...
Owners Manual - Page 7
... and suffer a drop in signal level of 6 dB.
7 Hookup Diagrams
Stereo Speaker Hookup
S-8 ACTIVE STUDIO MONITOR
INPUTS
SETTINGS
PHONO
XLR
HIGH FREQ FILTER
TRS
-2dB 0 +2dB (NORMAL)
LOW FREQ FILTER
OFF
MAX
INPUT LEVEL
0 +2dB +4dB (NORMAL)
S-8 ACTIVE STUDIO MONITOR
INPUTS
SETTINGS
PHONO
XLR
HIGH FREQ FILTER
TRS
-2dB 0 +2dB (NORMAL)
LOW FREQ FILTER
OFF
MAX...
Owners Manual - Page 8
...monitor or to
another amplifier.
8
the sound of the speakers. HIGH FREQ Switch
connected
The HIGH FREQ
together electrically, do this switch in signal level (by 6 dB). NO USER SERVICEABLE PARTS INSIDE. NE PAS OUVRIR
SERIAL /DATE CODE
AC SELECT
115V
5
CAUTION: REPLACE... MACKIE DESIGNS...ACTIVE STUDIO MONITOR
INPUTS
RCA (UNBALANCED)
XLR
3 (BALANCED)
TRS (BALANCED)
4
SETTINGS ...
Owners Manual - Page 9
... voltage setting for information about replacing the fuse.
11 8.
Note: The S•8s are in a country that
level. See the "Troubleshooting" section on page 11 for instructions on page 11 for the country you are shipped with the 1.6 A fuse included in power amplifiers. POWER
Use this switch to turn the active monitors on...
Owners Manual - Page 10
...support department for the low-frequency and high-frequency amplifiers. Integrated Magnetic Shielding
The S•8 contains drivers with computer monitors... in both electrically and thermally. • If for studio wiring.
• Microphone cables work well.
•... heatsink to a CRT (cathode ray tube). Your Mackie dealer may be necessary to connect the speaker outputs ...
Owners Manual - Page 11
...plugged all the way back into the preamp stage. It's possible your TAPCO S•8 has a problem, please do . Troubleshooting
No Power
• Our favorite question: Is it plugged in? &#..."Repair" section on the front panel illuminated? Reduce the signal level at the monitor end. Disconnect the power cord from the mixing console (or whatever device immediately precedes the studio monitor)...
Owners Manual - Page 12
..., to explain the problem and request an RA (Return Authorization) number. This is very important. If your monitor's serial number ready. Please.
2. Have your monitor needs service, follow these instructions: 1.
Have I reached the party to non-warranty repair. Review the preceding troubleshooting suggestions. Ship the monitor to repair the monitor.
4. Ask Tech Support for the latest...
Owners Manual - Page 14
... mm with steel frame, polypropylene cone woofer
High Frequency: Wave guide loaded 1 in/25 mm silk dome tweeter
Equalization
Low Frequency EQ... H/250 V
230 VAC: T 800 mA H/250 V
Power Consumption: 80 watts with music, loud mix
20 watts quiescent (idle)
Amplifiers...FREQUENCY DRIVER
TWEET
STAIRWAY TO
HEAVEN
-HI VDC
11
+HI VDC LO-FREQUENCY
POWER AMPLIFIER
CLIP LED
LO-FREQUENCY DRIVER
WOOF...
Owners Manual - Page 15
...TAPCO DEALER. This warranty provides specific legal rights and you . "Mackie." All Rights Reserved.
15 B.
LOUD Technologies may use refurbished parts for repair or replacement under warranty at its authorized dealers. TAPCO...MAY RESULT FROM ANY DEFECT IN THE TAPCO PRODUCT OR ANY WARRANTY CLAIM. To obtain factory service, please follow the instructions found in the form of a ...
Owners Manual - Page 16
are registered trademarks of LOUD Technologies Inc. All rights reserved."TAPCO" and "Mackie." tapcogear.com
©2003 LOUD Technologies Inc.
Mackie S-8 Reviews
We have not received any reviews for Mackie yet.