Installation Guide
Page 4
... vent installations) Leveling legs (4) Parts supplied (steam models): "Y" connector 2' (0.6 m) inlet hose Caulking gun and compound (new vent installations) Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench Rubber washer Parts package is located in dryer drum. NOTE: Do not use leveling legs supplied with dryer if installing with dryer) ■■Vent clamps ■■Vent elbows and vent work 4 Parts needed for gas installations: 8" or 10" pipe wrench 8" or 10" adjustable wrench (for gas connections...
... vent installations) Leveling legs (4) Parts supplied (steam models): "Y" connector 2' (0.6 m) inlet hose Caulking gun and compound (new vent installations) Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench Rubber washer Parts package is located in dryer drum. NOTE: Do not use leveling legs supplied with dryer if installing with dryer) ■■Vent clamps ■■Vent elbows and vent work 4 Parts needed for gas installations: 8" or 10" pipe wrench 8" or 10" adjustable wrench (for gas connections...
Installation Guide
Page 5
... using a pedestal, you will be exposed to water and/or weather. Read "Electrical Requirements" and "Venting Requirements" before purchasing parts. measurement NOTE: Most installations require a minimum of 5" (127 mm) clearance behind dryer for exhaust vent with dryer) Refer to your Use and Care Guide for information about accessories available for your installation. Back view: * Approx. Parts needed (steam models): DRYER DIMENSIONS Front view: 27" (686 mm) 5' (1.52 m) inlet hose Additional parts may be required, depending on your washer using the supplied "Y" connector...
... using a pedestal, you will be exposed to water and/or weather. Read "Electrical Requirements" and "Venting Requirements" before purchasing parts. measurement NOTE: Most installations require a minimum of 5" (127 mm) clearance behind dryer for exhaust vent with dryer) Refer to your Use and Care Guide for information about accessories available for your installation. Back view: * Approx. Parts needed (steam models): DRYER DIMENSIONS Front view: 27" (686 mm) 5' (1.52 m) inlet hose Additional parts may be required, depending on your washer using the supplied "Y" connector...
Installation Guide
Page 6
... moldings. Mobile home installations require: ■■Metal exhaust system hardware, available for wall, door, floor moldings, dryer venting, and gas line. ■■Additional spacing should also be at least twice as large as a dryer. Contact your Use and Care Guide. ■■Special provisions must conform to reduce noise transfer. ■■For closet installation with equivalent ventilation openings are required. Installation spacing for recessed...
... moldings. Mobile home installations require: ■■Metal exhaust system hardware, available for wall, door, floor moldings, dryer venting, and gas line. ■■Additional spacing should also be at least twice as large as a dryer. Contact your Use and Care Guide. ■■Special provisions must conform to reduce noise transfer. ■■For closet installation with equivalent ventilation openings are required. Installation spacing for recessed...
Installation Guide
Page 7
... use Power Supply Cord Replacement Part Number 8529008. Do not modify the plug provided with all local codes. or 20- ELECTRIC DRYER POWER HOOKUP - CANADA ONLY ELECTRICAL REQUIREMENTS GAS DRYER POWER HOOKUP ELECTRICAL REQUIREMENTS It is your Use and Care Guide. latest edition and all local codes and ordinances. A time-delay fuse or circuit breaker is required. Be sure wall receptacle is within reach of your responsibility: ■■To contact a qualified electrical installer. ■■To be plugged into an appropriate outlet...
... use Power Supply Cord Replacement Part Number 8529008. Do not modify the plug provided with all local codes. or 20- ELECTRIC DRYER POWER HOOKUP - CANADA ONLY ELECTRICAL REQUIREMENTS GAS DRYER POWER HOOKUP ELECTRICAL REQUIREMENTS It is your Use and Care Guide. latest edition and all local codes and ordinances. A time-delay fuse or circuit breaker is required. Be sure wall receptacle is within reach of your responsibility: ■■To contact a qualified electrical installer. ■■To be plugged into an appropriate outlet...
Installation Guide
Page 8
... dryer. Gas shut-off valve must be installed within six (6) ft. (1.8 m) of your Use and Care Guide. NOTE: Pipe-joint compounds that an individual manual shut-off valve must have the correct burner for the type of your dryer to reach for opening and closing . If this information does not agree with a different gas without consulting your home. Burner information is located on the model/serial rating plate for use...
... dryer. Gas shut-off valve must be installed within six (6) ft. (1.8 m) of your Use and Care Guide. NOTE: Pipe-joint compounds that an individual manual shut-off valve must have the correct burner for the type of your dryer to reach for opening and closing . If this information does not agree with a different gas without consulting your home. Burner information is located on the model/serial rating plate for use...
Installation Guide
Page 10
... fire, this dryer MUST BE EXHAUSTED OUTDOORS. Then, test all connections by brushing on threads of flexible metal vent used to connect dryer to avoid sagging and kinking that may result in reduced airflow and poor performance. ■■ Do not install in final dryer location. ■■ Remove excess to existing gas line. Replace plastic or metal foil vents with lint. Open shut-off valve in the "Vent System Charts...
... fire, this dryer MUST BE EXHAUSTED OUTDOORS. Then, test all connections by brushing on threads of flexible metal vent used to connect dryer to avoid sagging and kinking that may result in reduced airflow and poor performance. ■■ Do not install in final dryer location. ■■ Remove excess to existing gas line. Replace plastic or metal foil vents with lint. Open shut-off valve in the "Vent System Charts...
Installation Guide
Page 12
... a long vent system, refer to the type code located on the next page to determine type of dryer. ■■Reduce performance, resulting in longer drying times and increased energy usage. Example: An electric model would be DALV - ELE - A gas model would be securely fastened to exhaust hood Vent must not terminate beneath the mobile home. GAS - Install exhaust hood 12" min. (305 mm) 12" min. (305 mm) Install exhaust hood and use vent runs...
... a long vent system, refer to the type code located on the next page to determine type of dryer. ■■Reduce performance, resulting in longer drying times and increased energy usage. Example: An electric model would be DALV - ELE - A gas model would be securely fastened to exhaust hood Vent must not terminate beneath the mobile home. GAS - Install exhaust hood 12" min. (305 mm) 12" min. (305 mm) Install exhaust hood and use vent runs...
Installation Guide
Page 15
.... Gas Models q Plug into a grounded outlet. All Models: q Select a Timed Dry heated cycle, and start of the water system, which will go back through the water system in a hard water area, use wrench to be level for certain part replacement or repair. Do not select Air Only Temperature setting. Not Level LEVEL 2. Once dryer is level. q Remove film on console and any dust. q Check to adjust legs up using a wood block, use of a water softener is first used...
.... Gas Models q Plug into a grounded outlet. All Models: q Select a Timed Dry heated cycle, and start of the water system, which will go back through the water system in a hard water area, use wrench to be level for certain part replacement or repair. Do not select Air Only Temperature setting. Not Level LEVEL 2. Once dryer is level. q Remove film on console and any dust. q Check to adjust legs up using a wood block, use of a water softener is first used...
Warranty Information
Page 1
... state or province to Maytag within 30 days. 10. Proof of original purchase, when this major appliance is a limited 10 year warranty on the right to determine if another warranty applies. In-home instruction on the duration of implied warranties of product replacement, your product requires repair. house wiring, fuses, or water inlet hoses). 4. light bulbs, batteries, air or water filters, preservation solutions, etc.). 5. Conversion of the product. 14...
... state or province to Maytag within 30 days. 10. Proof of original purchase, when this major appliance is a limited 10 year warranty on the right to determine if another warranty applies. In-home instruction on the duration of implied warranties of product replacement, your product requires repair. house wiring, fuses, or water inlet hoses). 4. light bulbs, batteries, air or water filters, preservation solutions, etc.). 5. Conversion of the product. 14...
Use & Care Guide
Page 7
... used with High or Medium heat settings. Check Lint Screen The Check Lint Screen indicator will not light up. The Cycle Status Indicators show the status of a cycle. Steam Boost Steam Boost adds steam to the end of the dryer and avoid an accidental change in cycle options or preferences during a drying cycle. For more information on or off . To unlock the control, touch and hold CONTROL LOCK for about one second to turn...
... used with High or Medium heat settings. Check Lint Screen The Check Lint Screen indicator will not light up. The Cycle Status Indicators show the status of a cycle. Steam Boost Steam Boost adds steam to the end of the dryer and avoid an accidental change in cycle options or preferences during a drying cycle. For more information on or off . To unlock the control, touch and hold CONTROL LOCK for about one second to turn...
Use & Care Guide
Page 8
... Normal Steam Boost* Less Cycle Details: Offers stepped drying starting with high heat, which has been proven to about 1/2 full. Medium load: Fill the dryer drum up to reduce household bacteria. CYCLE GUIDE - Not all fabrics. Small load: Fill the dryer drum with High and Medium Drying Temperature settings. * On steam models only. SENSOR CYCLES Settings and options shown in the load or air temperature and shuts off when the load reaches the selected dryness level. Use Sensor Cycles...
... Normal Steam Boost* Less Cycle Details: Offers stepped drying starting with high heat, which has been proven to about 1/2 full. Medium load: Fill the dryer drum up to reduce household bacteria. CYCLE GUIDE - Not all fabrics. Small load: Fill the dryer drum with High and Medium Drying Temperature settings. * On steam models only. SENSOR CYCLES Settings and options shown in the load or air temperature and shuts off when the load reaches the selected dryness level. Use Sensor Cycles...
Use & Care Guide
Page 9
... you are changed, the new settings will return to the default. STEAM CYCLE (on Rapid Dry). Large load: Fill the dryer drum up to reduce light wrinkles from loads left in your load. Items need to the care label directions. The maximum dry time is available only with dry loads to add a short steam cycle after 60 minutes. Use a no heat (air only) setting for drying medium-weight items such as towels and work clothes. Line dry bonded or laminated...
... you are changed, the new settings will return to the default. STEAM CYCLE (on Rapid Dry). Large load: Fill the dryer drum up to reduce light wrinkles from loads left in your load. Items need to the care label directions. The maximum dry time is available only with dry loads to add a short steam cycle after 60 minutes. Use a no heat (air only) setting for drying medium-weight items such as towels and work clothes. Line dry bonded or laminated...
Use & Care Guide
Page 12
... cloth. 2. REMOVING ACCUMULATED LINT From Inside the Dryer Cabinet Lint should be used with the holes in the cycle by calling 1-877-944-7566. Start the dryer. DRYER CARE CLEANING THE DRYER LOCATION Keep dryer area clear and free from items dried on the dryer back ledge. 3. These stains are not harmful to circulate. Use the Drying Rack for items that would block the air flow for your dryer, order by increasing or decreasing the cycle time...
... cloth. 2. REMOVING ACCUMULATED LINT From Inside the Dryer Cabinet Lint should be used with the holes in the cycle by calling 1-877-944-7566. Start the dryer. DRYER CARE CLEANING THE DRYER LOCATION Keep dryer area clear and free from items dried on the dryer back ledge. 3. These stains are not harmful to circulate. Use the Drying Rack for items that would block the air flow for your dryer, order by increasing or decreasing the cycle time...
Use & Care Guide
Page 14
... use to locate, level, and connect the dryer. 14 Unplug dryer or disconnect power. 2. Disconnect water inlet hose from faucet and drain. Reconnect water inlet hose to dryer pipe. 4. Transport hose separately. 7. Transport hose separately. 5. Steam models only: Shut off water faucet. 4. Gas models only: Disconnect gas supply line pipe and remove fittings attached to faucet. Disconnect power. 2. Disconnect wiring. 3. Turn on vacation or not using your dryer for an extended period of replacement. DRYER CARE NON-USE, STORAGE, AND MOVING CARE Install...
... use to locate, level, and connect the dryer. 14 Unplug dryer or disconnect power. 2. Disconnect water inlet hose from faucet and drain. Reconnect water inlet hose to dryer pipe. 4. Transport hose separately. 7. Transport hose separately. 5. Steam models only: Shut off water faucet. 4. Gas models only: Disconnect gas supply line pipe and remove fittings attached to faucet. Disconnect power. 2. Disconnect wiring. 3. Turn on vacation or not using your dryer for an extended period of replacement. DRYER CARE NON-USE, STORAGE, AND MOVING CARE Install...
Use & Care Guide
Page 15
... the outside exhaust hood to recommended load size in firm contact with no water line connected. Make sure the dryer door is open . There may make sure that both fuses are too long Dryer hasn't been used during cycle Dryer Results Clothes are not drying satisfactorily or drying times are intact and tight, or that the valve on . Replace the fuses or reset the circuit breaker. Gas valve operating. See the Installation Instructions. Check that both circuit breakers have heat. Incorrect power supply. Incorrect power supply...
... the outside exhaust hood to recommended load size in firm contact with no water line connected. Make sure the dryer door is open . There may make sure that both fuses are too long Dryer hasn't been used during cycle Dryer Results Clothes are not drying satisfactorily or drying times are intact and tight, or that the valve on . Replace the fuses or reset the circuit breaker. Gas valve operating. See the Installation Instructions. Check that both circuit breakers have heat. Incorrect power supply. Incorrect power supply...
Use & Care Guide
Page 16
... dryer's water inlet valve. The Sensor Cycle is not the correct size. The load was tightly packed. Check that water inlet hose is too short Lint on load Stains on load Stains on model) has been selected. Proper operation of fabric softener. Fabric softener sheets added to dry quickly. See the Installation Instructions. The dryer is located in clothing (usually blue jeans). Use 4" (102 mm) diameter vent material. The Air Only temperature setting or Air Dry cycle (depending on drum Loads are wrinkled...
... dryer's water inlet valve. The Sensor Cycle is not the correct size. The load was tightly packed. Check that water inlet hose is too short Lint on load Stains on load Stains on model) has been selected. Proper operation of fabric softener. Fabric softener sheets added to dry quickly. See the Installation Instructions. The dryer is located in clothing (usually blue jeans). Use 4" (102 mm) diameter vent material. The Air Only temperature setting or Air Dry cycle (depending on drum Loads are wrinkled...
Use & Care Guide
Page 17
... a problem that water inlet hose is located. Select a Sensor cycle with an "F" appears in garments after wearing. Touch and hold CONTROL LOCK for details. • Select a Timed Dry heated cycle, and restart the dryer. • If the message persists, have your (low or no line voltage home power supply, keeping the condition) dryer's heater from turning on . Touch any setting or option name to clear the code from a power failure. Electric dryers use two...
... a problem that water inlet hose is located. Select a Sensor cycle with an "F" appears in garments after wearing. Touch and hold CONTROL LOCK for details. • Select a Timed Dry heated cycle, and restart the dryer. • If the message persists, have your (low or no line voltage home power supply, keeping the condition) dryer's heater from turning on . Touch any setting or option name to clear the code from a power failure. Electric dryers use two...
Use & Care Guide
Page 18
... U.S.A. Service to Maytag within 30 days. 10. light bulbs, batteries, air or water filters, preservation solutions, etc.). 5. DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY Maytag makes no representations about buying an extended warranty. Please take a few minutes to review the Troubleshooting or Problem Solver section of your appliance will pay for factory specified parts for service in which it was purchased. Conversion of the Use and Care Guide, scan the QR code...
... U.S.A. Service to Maytag within 30 days. 10. light bulbs, batteries, air or water filters, preservation solutions, etc.). 5. DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY Maytag makes no representations about buying an extended warranty. Please take a few minutes to review the Troubleshooting or Problem Solver section of your appliance will pay for factory specified parts for service in which it was purchased. Conversion of the Use and Care Guide, scan the QR code...
Instruction Sheet
Page 1
... these instructions before proceeding. Installation of this kit. The kit number shown on the Burner Data Label located on the Burner Base may not match the kit you received is an approved kit for use with supply pressure between 8" (203 mm) and 13" (330 mm) water column. The qualified service agency is converted for converting your gas dryer from Natural Gas to Liquefied Petroleum (Bottled Gas) Parts included in Kit: 1 Instruction Sheet 1 Blocking...
... these instructions before proceeding. Installation of this kit. The kit number shown on the Burner Data Label located on the Burner Base may not match the kit you received is an approved kit for use with supply pressure between 8" (203 mm) and 13" (330 mm) water column. The qualified service agency is converted for converting your gas dryer from Natural Gas to Liquefied Petroleum (Bottled Gas) Parts included in Kit: 1 Instruction Sheet 1 Blocking...
Instruction Sheet
Page 12
.... Set dryer cycle to dryer. 2. Reattach dryer top or top and console assembly (depending on dryer. 8. Plug in "Disassembling the Dryer." 3. Turn off gas supply. 12. If no bubbles are present, tighten the leaking connection and retest for leaks in place and lint filter has been installed to time dry, high heat and turn off gas supply, tighten the leaking connection and retest for leaks indicated by : • Turning on dryer. • Running on supply line...
.... Set dryer cycle to dryer. 2. Reattach dryer top or top and console assembly (depending on dryer. 8. Plug in "Disassembling the Dryer." 3. Turn off gas supply. 12. If no bubbles are present, tighten the leaking connection and retest for leaks in place and lint filter has been installed to time dry, high heat and turn off gas supply, tighten the leaking connection and retest for leaks indicated by : • Turning on dryer. • Running on supply line...