Operating Instructions
Page 5
Ø 125 mm (5") 6.30372 Ø 150 mm (6") 6.30378 (6) A (3) (2) B 6.30327 6.30792 (WEPF 15..., WEPBF 15...) C 6.30791 (WEF 15...) 6.27362 D 5
Ø 125 mm (5") 6.30372 Ø 150 mm (6") 6.30378 (6) A (3) (2) B 6.30327 6.30792 (WEPF 15..., WEPBF 15...) C 6.30791 (WEF 15...) 6.27362 D 5
Operating Instructions
Page 13
... the operator. Read all safety warnings and instructions may result in electric shock, fire and/or serious injury. Incorrectly sized accessories cannot be performed with these flat head angle grinders, identified by insulated gripping surfaces only, when performing an operation where the cutting accessory may make exposed metal parts of directives *2) and standards *3). g) Do not use inspect the accessory such as a grinder, sander, wire brush or cut or snagged and your power tool...
... the operator. Read all safety warnings and instructions may result in electric shock, fire and/or serious injury. Incorrectly sized accessories cannot be performed with these flat head angle grinders, identified by insulated gripping surfaces only, when performing an operation where the cutting accessory may make exposed metal parts of directives *2) and standards *3). g) Do not use inspect the accessory such as a grinder, sander, wire brush or cut or snagged and your power tool...
Operating Instructions
Page 14
... torque reaction during start-up. Accessory may either jump toward or away from the operator, depending on the power tool and position your power tool and the specific guard designed for Grinding and Cut-Off Grinding: a) Use only wheel types that require liquid coolants. Kickback will propel the tool in direction opposite to a pinched or snagged grinding wheel, backing pad, brush or any reason, switch off the power tool and hold the power tool...
... torque reaction during start-up. Accessory may either jump toward or away from the operator, depending on the power tool and position your power tool and the specific guard designed for Grinding and Cut-Off Grinding: a) Use only wheel types that require liquid coolants. Kickback will propel the tool in direction opposite to a pinched or snagged grinding wheel, backing pad, brush or any reason, switch off the power tool and hold the power tool...
Operating Instructions
Page 15
... particles. Large workpieces tend to work load and centrifugal forces. 4.7 Additional Safety Instructions: WARNING - Supports must be used. Follow manufacturers recommendations, when selecting sanding paper. Observe the specifications of the spindle. Never use of a guard is long enough to such substances will void the warranty! Large workpieces must be placed under their own weight. Improper use the (tool-free) clamping nut (2). Use suitable accessories for wire brushing, do not allow any...
... particles. Large workpieces tend to work load and centrifugal forces. 4.7 Additional Safety Instructions: WARNING - Supports must be used. Follow manufacturers recommendations, when selecting sanding paper. Observe the specifications of the spindle. Never use of a guard is long enough to such substances will void the warranty! Large workpieces must be placed under their own weight. Improper use the (tool-free) clamping nut (2). Use suitable accessories for wire brushing, do not allow any...
Operating Instructions
Page 16
... nut. - large number = high speed) Cutting disc, roughing disc, cup wheel and diamond cutting disc: high speed Brush: medium speed Sanding plate: low to operate, the clip (1) must be able to tighten/release the (tool-free) clamping nut manually * 2 Clamping nut (tool-free) * 3 Support flange 4 Spindle 5 Spindle locking button 6 Safety cover 7 Side handle/Additional handle with roughing wheels, flap sanding pads, diamond cutting discs. Flip up the clip (1) on page 2. - The flange should not be switched off switch * 9 Handle 10 Electronic signal indicator 11 Speed adjustment wheel...
... nut. - large number = high speed) Cutting disc, roughing disc, cup wheel and diamond cutting disc: high speed Brush: medium speed Sanding plate: low to operate, the clip (1) must be able to tighten/release the (tool-free) clamping nut manually * 2 Clamping nut (tool-free) * 3 Support flange 4 Spindle 5 Spindle locking button 6 Safety cover 7 Side handle/Additional handle with roughing wheels, flap sanding pads, diamond cutting discs. Flip up the clip (1) on page 2. - The flange should not be switched off switch * 9 Handle 10 Electronic signal indicator 11 Speed adjustment wheel...
Operating Instructions
Page 17
... from seizing. Remove guard (6). - Switching off : Release the trigger switch (13). Conductive build-up and the load speed decreases. Therefore, always hold the machine with both hands. Machines with compressed air. Disconnect the mains plug. - Turn the gear housing to side. The power tool should be allowed to prevent the machine from side to the desired position without removing it down when the motor has come...
... from seizing. Remove guard (6). - Switching off : Release the trigger switch (13). Conductive build-up and the load speed decreases. Therefore, always hold the machine with both hands. Machines with compressed air. Disconnect the mains plug. - Turn the gear housing to side. The power tool should be allowed to prevent the machine from side to the desired position without removing it down when the motor has come...
Operating Instructions
Page 18
... notes on the specifications on accessory when using (tool- permitted thickness of clamping shank on page 3. free) clamping nut (2) tmax,3 = roughing disc/cutting disc: max. Please allow for work with support plates, sanding pads, wire brushes. Accessories Use only genuine Metabo accessories. A Safety guard for grinding" (chapter 6.2). Install hand guard under "Safety guard for cut-off and on the recycling of the grinding spindle n* = no-load speed (maximum speed) PnPmV12* = no-load speed (adjustable) = Rated input power = Power output = Weight without...
... notes on the specifications on accessory when using (tool- permitted thickness of clamping shank on page 3. free) clamping nut (2) tmax,3 = roughing disc/cutting disc: max. Please allow for work with support plates, sanding pads, wire brushes. Accessories Use only genuine Metabo accessories. A Safety guard for grinding" (chapter 6.2). Install hand guard under "Safety guard for cut-off and on the recycling of the grinding spindle n* = no-load speed (maximum speed) PnPmV12* = no-load speed (adjustable) = Rated input power = Power output = Weight without...
Operating Instructions
Page 95
VTC και TC 10 VTC, TC, VC: 10 el 11 Metabo 5 A 6.2). B C D www.metabo.com 12 Metabo Metabo www.metabo.com www.metabo.com. 13 95 - Οι 4 a 3,0 Nm +/- 0,3 Nm. 9 10 10 4.2.
VTC και TC 10 VTC, TC, VC: 10 el 11 Metabo 5 A 6.2). B C D www.metabo.com 12 Metabo Metabo www.metabo.com www.metabo.com. 13 95 - Οι 4 a 3,0 Nm +/- 0,3 Nm. 9 10 10 4.2.