Milwaukee Tool 2722-20 Support and Manuals
Get Help and Manuals for this Milwaukee Tool item
View All Support Options Below
Free Milwaukee Tool 2722-20 manuals!
Problems with Milwaukee Tool 2722-20?
Ask a Question
Free Milwaukee Tool 2722-20 manuals!
Problems with Milwaukee Tool 2722-20?
Ask a Question
Milwaukee Tool 2722-20 Videos
FINALLY!! I get to check out the SUPER SAWZALL from Milwaukee Tool (2722-20)
Duration: 3:05
Total Views: 2,510
Duration: 3:05
Total Views: 2,510
HEAD TO HEAD - RECIPROCATING SAW - MILWAUKEE Super Sawzall vs MILWAUKEE Sawzall (2722-20 vs 2821-20)
Duration: 5:00
Total Views: 55,705
Duration: 5:00
Total Views: 55,705
Popular Milwaukee Tool 2722-20 Manual Pages
Operators Manual - Page 2
... situation. •Keep handles and grasping surfaces dry, clean and free from frequent use of the tool in moving parts. Use of children and do the job better and safer at all
warnings and instructions for outdoor use a power tool while you are tired or under the influence of untrained users. •Maintain power...
Operators Manual - Page 3
... temperature range specified in the instructions. SPECIFIC SAFETY RULES FOR SAWZALL®
•Hold power tool by hand or against your...replacement parts. No 2722-20 Volts 18 DC Battery Type M18™ Charger Type M18™ No Load Strokes per Minute (SPM)
Read Operator's Manual
UL Listing for additional information or training.
•Maintain labels and nameplates. Service...
Operators Manual - Page 4
... may be
removed by this
specifically tool.
Broken blades can be inserted with the specified for a variety of the arrow
to avoid starting the
tool when changing blades. ASSEMBLY
WARNING
Recharge only with the teeth
Collar
facing up and down .
charger For spe-
cific charging instructions, read the operator's
manual supplied with small
teeth (such...
Operators Manual - Page 5
...set by use an OSHA compliant dust extraction solution. WARNING
To reduce the risk of the tool. The further the trigger is installed...tool may be adjusted by an authorized MILWAUKEE service facility. The amount of orbital action may be adjusted when the tool... control switch. Then guide the tool along your cutting line...specific cutting requirements. 1. Refer to avoid excessive vibration.
Operators Manual - Page 6
..., lower the blade into surfaces that may affect the tool operation. Plunge Cutting This MILWAUKEE Sawzall® is inserted. Using the edge of these instructions. NOTE: To make plunge cutting easier, use a heavy gauge blade and install the blade with technical, service/repair, or warranty questions. Contact a MILWAUKEE
service facility for plunge cutting directly into the workpiece as...
Operators Manual - Page 7
...Parts & Service section of a part including, but not limited to obtain the applicable warranty on this power tool which, after examination, is required. ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. cendie ou des blessures graves. Conserver les règles
et les instructions...SPECIFIC...
Service Parts List - Page 1
...
1
46 Spring Pin
1
99 14-46-2722 Blade Clamp Assembly
1
48 32-05-1070 Bevel Gear
1
49 43-06-0025 Metal Plate
1
50 40-50-0787 Disc Spring
1
57 02-50-1640 Needle Bearing
1
MILWAUKEE TOOL l www.milwaukeetool.com 13135 W. J66A
REVISED BULLETIN DATE Aug. 2022
WIRING INSTRUCTION
SEE PAGE 3
NOTE: Early production speed...
Service Parts List - Page 2
... gear of rotor
assembly (95), being sure to cover the middle of the gear and all teeth. Place 15g ±3g (approx. .5 ounce) to installing rollers (68). can) Place 30g ±3g (approx. 1 ounce) on both ends of Crankshaft Assembly #91
Connecting Rod Pin #11
Rollers #68
Bevel Gear...
Service Parts List - Page 3
...tightened using clean, dry, lint-free cloth. Wipe off only using a ft. lbs. PART NO. Place a 3/16" diameter x 1-1/2" long steel rod through spacer (15) ..." steel pin rest against crankshaft assembly connecting rod (See 'Removing Crankshaft Assembly' instructions above). lbs. WHERE USED
(KG/CM) (IN/LBS)
16 06-08-...-20 ft. SCREW TORQUE SPECIFICATIONS
SEAT TORQUE
FIG.
Service Parts List - Page 4
... these instructions to rotate freely. Center the shoe pin with flats aligned) and press into groove. The use of parts and...CLAMP
• Coat new lock pin with powdered graphite.
69
• Hold tool in a vertical position.
2
• Place spring cover (1) onto spindle.
...)
Shoe Pin #65 Shoe Release Lever #64
To properly install the Shoe Release Lever #64 onto the Shoe Pin #65...
Service Parts List - Page 5
... Assembly
Motor Housing
Speed Select Board Assembly 5 Wire Ribbon Power Board/ Hall Board Assemblies 20 Pin Cable Ribbon Control Board Assembly
Left Housing Halve (Support)
Speed Board/Battery Connector Block Assemblies
SEE PAGE 6 FOR ADDITIONAL WIRING VIEWS
Prior to installing Right Handle/Housing Halve (38) onto left housing/handle halve (30), be sure...
Milwaukee Tool 2722-20 Reviews
We have not received any reviews for Milwaukee Tool yet.