Milwaukee Tool 6470-21 Support and Manuals
Get Help and Manuals for this Milwaukee Tool item
This item is in your list!
View All Support Options Below
Free Milwaukee Tool 6470-21 manuals!
Problems with Milwaukee Tool 6470-21?
Ask a Question
Free Milwaukee Tool 6470-21 manuals!
Problems with Milwaukee Tool 6470-21?
Ask a Question
Popular Milwaukee Tool 6470-21 Manual Pages
Operators Manual - Page 2
... in personal injury. •Do not overreach. Keep your power tool serviced by poorly maintained power tools. •Keep cutting tools sharp and clean. Always wear eye protection. A wrench or a key left attached to a rotating part of dust extraction and collection facilities, ensure these instructions to power source and/or battery pack, picking up or carrying...
Operators Manual - Page 3
...Supports must be serviced before each use dull or damaged blades. Unsharpened or improperly set...MILWAUKEE service facility for special cuts such as those dust masks that can be retracted manually only for a free replacement... where the cutting tool may walk up... or straight edge guide. Further safety instructions for optimum performance ... and make exposed metal parts of debris. •...
Operators Manual - Page 4
.... Always replace a damaged extension cord or have it . • Protect your extension cord is damaged.
If the plug will not fit the outlet, have a three
wire cord and three prong grounding plug. The green wire in the tool. A
Double Insulated Tools: Tools with Three Prong Plugs
Tools marked "Grounding Required" have a proper outlet installed by a MILWAUKEE service facility...
Operators Manual - Page 5
... the tool and increase the chance of tool. Only use thin kerf blades with
maximum speed rating at 60˚
0 to the blade. Do not use sharp blades. Miter scale
13. Auxiliary handle 2. Lower guard
6. functional description
3
2
1
11. 60˚ Override button 12. Blade bolt 7. No. 6470-21
Volts AC
120
Amps 15
Specifications
No...
Operators Manual - Page 6
...Unplug tool before ...tool. 2. Lowering saw will not show proper lower guard operation if the tool...tool) until spindle locks. Place the tool...to damaged parts, gummy... be serviced before ...side. 3.
Installing Blade 1.
...tool. 2. To remove blade, reverse the above steps.
Fig. 1
Rip & Crosscut A multi-purpose blade for repairs... a MILWAUKEE service facility ... . Unplug tool. 2.
Place...
Operators Manual - Page 7
...injury,
always unplug tool before cutting. Turn...firm grip with the shoe. 5. Unplug tool. 2. Fig. 5
Kickback causes and...Supports must be controlled by the kerf closing down miter lever to a 90 degree setting. Fig. 4
4. To adjust the degree setting... shields.
7 Set the bevel pointer to inspect the degree setting (Fig. 5)....blade is restarted. •Support large panels to resist kickback...
Operators Manual - Page 8
...• Failure to use rip fence or guide If blade binds, smokes, or turns blue...through the work in different situations. Troubleshooting If blade does not want to...Set depth of cut 1/8"-1/4" greater than thickness of stock
Rest saw on larger part of workpiece, allowing smaller part to fall away
Firm footing in clean area
Secure workpiece to sturdy supports
8 Unsharpened or improperly set...
Operators Manual - Page 9
...job. Cross-Cutting Wood Cross-cutting is used to a MILWAUKEE service facility for cleaning and testing before using bonded abrasive wheels on... to set the depth of tool. Support large panels. Be sure to make a pocket cut without leveling and properly supporting the ...To install a rip fence, slide the bar through the rip fence slot in the middle of cut through the supports....
Operators Manual - Page 10
... need to do any other insulated parts. After six months to assure proper mechanical and electrical operation
WARNING To reduce the risk of oil or grease. Use only specifically recommended accessories. Maintaining Tools Keep your tool to the nearest MILWAUKEE service facility for the following: • Lubrication • Brush inspection and replacement • Mechanical inspection and...
Operators Manual - Page 11
... guide or instruction manual. c) When the product was modified or repaired by people not authorized by the distributor or store where you purchased the product, and there any defect in material or workmanship for 5 year since the original purchase date. Please consult the 'Service Center Search' in the U.S.A. We will be replaced by anyone other than MILWAUKEE...
Operators Manual - Page 36
... at www.milwaukeetool.com For service information, use the 'Service Center Search' icon found in the 'Parts & Service' section. Contact our Corporate After Sales Service Technical Support about ... • Technical Questions • Service/Repair Questions • Warranty
call ... Vendredi 7:00 - 4:30 CST fax: 866.285.9049
Milwaukee Electric Tool (Canada) Ltd
140 Fernstaff Court, Unit...
Service Parts List - Page 1
... (1) (2) (1) (1) (1) (1) (1) (1)
MILWAUKEE ELECTRIC TOOL CORPORATION 13135 W.
Ball Bearing
(1)
Ball Bearing
(1)...PARTS
10-1/4" CIRCULAR SAW
CATALOG NO.
6470-21
STARTING SERIAL NO. T-25 Screw
(7)
8-16 x .5 Pan Hd. Plast. AND SERIAL NO.
BULLETIN NO. 54-40-1940
REVISED BULLETIN
DATE
Sept. 2018
WIRING INSTRUCTION
58-01-0756
6X
SEE REVERSE SIDE
FOR LUBRICATION
*
AND SERVICE...
Service Parts List - Page 2
... from engagement in the Upper Guard/
Gearcase (41) before assembling the Armature Bearing (2).
41 Place 1/2 Oz. Place the saw up side down with the saw set at full depth of the Armature (27).
4 Orient the Needle Bearing (4) such that the beveled face is facing the Gear (49). Press the bear ing...
Milwaukee Tool 6470-21 Reviews
Do you have an experience with the Milwaukee Tool 6470-21 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Milwaukee Tool yet.
Earn 750 points for your review!