Milwaukee Tool Diamond Coring Motor 300/600 RPM 20 Amp with Clutch Support and Manuals
Get Help and Manuals for this Milwaukee Tool item
View All Support Options Below
Free Milwaukee Tool Diamond Coring Motor 300/600 RPM 20 Amp with Clutch manuals!
Problems with Milwaukee Tool Diamond Coring Motor 300/600 RPM 20 Amp with Clutch?
Ask a Question
Free Milwaukee Tool Diamond Coring Motor 300/600 RPM 20 Amp with Clutch manuals!
Problems with Milwaukee Tool Diamond Coring Motor 300/600 RPM 20 Amp with Clutch?
Ask a Question
Popular Milwaukee Tool Diamond Coring Motor 300/600 RPM 20 Amp with Clutch Manual Pages
Operators Manual - Page 2
... extraction and collection facilities, ensure these instructions, taking into account the working conditions and
•Stay alert, watch what you to be performed. A careless action can cause you are caused by a qualified repair person using only identical replacement parts. tool for outdoor use a liquid collection device. Water entering a power tool will ensure that requires the use...
Operators Manual - Page 3
... 3"
3 Have dam-
aged parts repaired or replaced by a MILWAUKEE
service facility.
•
WARNING
To reduce plications
the risk of work - These carry important information. To reduce your capability; No 4079 Amps 20 Motor Protection Shear Pin Speed Low 300 High 600 Suggested Diameter in
Medium Aggregate.......... No 4094 Amps 20 Motor Protection Shear Pin Speed Low 450...
Operators Manual - Page 4
...INSTRUCTIONS FOR FUTURE USE.
3
1. SYMBOLOGY
Volts Alternating Current Amps
No Load Revolutions per Minute (RPM)
C US UL Listing for more than a 16 gauge cord. Twist-lock plug 2. Always replace a
damaged extension cord or have it repaired by a
qualified person before using more than one tool...damp or wet areas.
Nameplate
7
Clutch model
6
1
Guidelines for Using Extension ...
Operators Manual - Page 5
....
Always position
the GFCI as close as to a properly
grounded outlet (See Figures A and Fig. Set the base on the ground. 2. Grounded Tools (Three-Prong Plugs)
Tools marked "Grounding Required"
have a
proper outlet installed by a MILWAUKEE service facility before
injury, always changing or
removing accessories.
Fig.
For Cat. Place the column in...
Operators Manual - Page 6
... the cradle on the column using the four (4) 1/4"-20 threaded socket head screws and four (4) lock washers (.... 9. Replace the meter stud on the Dymodrill motor. 3. Attach the meter box to prevent the motor or bit from wobbling during coring. Replace the four... NOTE: For horizontal (wall) coring, the ammeter gauge must be purchased separately for installing the bit later. A meter...
Operators Manual - Page 7
... the Dymodrill
Hose nut
Rubber washer
Attach to prevent the motor or bit from Washer
seizing on a vertical surface. Tighten the twelve (12) gib screws with an anchor gives better bit performance because the attachment is more rigid. Selecting and Installing a Core Bit
MILWAUKEE offers both standard and premium
Dymobits designed to wiggle the...
Operators Manual - Page 8
...20 inches of mercury vacuum, tighten the vacuum pad nut securely.
8 Before using the bubble level (4125 & 4130 only) as a guide... following the anchor manufacturer's instructions.
The vacuum pad is most...screws. See "Accessories" for coring the hole. 3. Plug ...for gasket part number. 1. When the rig is , immediately replace the gasket...Rig® and they can be set the stand upright. 2. To ...
Operators Manual - Page 9
...replace the gasket, see "Securing the Equipment to help
prevent motor...set on the vacuum pump following the manufacturer's
instructions.
To reduce the risk of injury DO NOT
CORE if the gauge reads less than 20...vacuum. The ammeter provides
20 Amp Operating Range
pressure feedback
during...replace the gasket, otherwise the vacuum may be
purchased separately for gasket part number.
...
Operators Manual - Page 10
.... When you turn the motor OFF. Meter Boxes provide a switch to
turn off valve (see "Diamond Coring"). It is possible
for the threaded spindle sleeve and the internal
spindle to weld together and seize during coring
(see "Accessories"). Shear Pin
Spindle Sleeve (Shear pin models) Threaded Spindle (Clutch Models)
Retaining Ring (shear pin model only)
Cat.
Use a standard...
Operators Manual - Page 11
...vibrate during coring: 1. Consult motor guide in its...coring. •Motors should be of proper size (amperage and RPM) for approximately 3 to the nearest MILWAUKEE service facility. Standing on the rig's base as needed.
11 Resume drilling for the diameter of the core bit used. Gradually increase water flow to bit glazing. Replace if required. This preserves the integrity of the diamonds...
Operators Manual - Page 12
...Effects of Steel in Coring •To self-sharpen, diamond-impregnated core bits require interaction with a Shear Pin
Before each use flammable or combustible solvents around tools. MAINTENANCE
WARNING
To reduce the risk of MILWAUKEE Type "E" Grease on shear pin models, re-
Maintaining Tools Keep your tool purchases. Return the tool to the nearest service center. After six...
Operators Manual - Page 13
... not apply to damage that MILWAUKEE determines to be replaced by MILWAUKEE to avoid electric risks. Normal Wear: Many power tools need periodic parts replacement and service to 01 (800) 030-7777 IMPORTED AND COMMERCIALIZED BY TECHTRONIC INDUSTRIES MEXICO, SA DE CV Av President Masarik #29 piso 7, Col. This warranty does not cover repair when normal use are...
Milwaukee Tool Diamond Coring Motor 300/600 RPM 20 Amp with Clutch Reviews
We have not received any reviews for Milwaukee Tool yet.