NEC E222W - MultiSync - 22" LCD Monitor Support and Manuals
Get Help and Manuals for this NEC item
NEC E222W Videos
Nec e222w
Duration: 1:37
Total Views: 562
Duration: 1:37
Total Views: 562
Popular NEC E222W Manual Pages
User Manual - Page 3
... operating the MultiSync E222W monitor with its AC 125-240V power supply, use a power supply cord that the colour monitor MultiSync E222W (L227HR) ...Information
Declaration
Declaration of this unit. EN 61000-3-2 - NO USER SERVICEABLE PARTS INSIDE. If a power cord is not supplied with the..., it should be serviced in the country where it is in order to avoid any problems.
CAUTION: Please use...
User Manual - Page 4
...the U.S. If necessary, the user should contact the dealer or an experienced radio/television technician for help.
Windows is encouraged to try to ...Part 15 of the FCC Rules. This booklet is a U.S.
Responsible Party: Address:
Tel. NEC is no guarantee that may cause interference with the MultiSync E222W (L227HR) color monitor so as specified in a residential installation...
User Manual - Page 5
... no user serviceable parts inside and opening or removing covers may expose
you use must have fallen into the cabinet slots, as the previous image was on the screen.
To alleviate image persistence, turn off for use
Safety Precautions and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING
THE MULTISYNC...
User Manual - Page 7
... the User's Manual, Acrobat Reader 4.0 or higher must be installed on the where the LCD monitor is to be shipped)
Setup Manual
CD ROM Base stand
Setup Manual
15-pin mini D-SUB male to 15-pin mini D-SUB male
* Remember to transport or ship the monitor.
English
Contents
Your new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD monitor with...
User Manual - Page 8
... attach the MultiSync LCD monitor to the connector of base stand bottom (Figure 2). For the PC with DVI digital output: Connect the DVI signal cable to LCD monitor and lock screws of the display card in your computer. 2. Place hands on each side of the display card in your system, follow these instructions: 1. Connect...
User Manual - Page 9
... desired (Figure TS.1). NOTE: If you have any problems, please refer to Caution section of this User's Manual. NOTE: Please refer to the Troubleshooting section of these OSD controls. To raise or lower screen, place hands on the monitor with care when raising or lowering the monitor screen. Figure RL.1
Tilt and Swivel
Grasp both sides...
User Manual - Page 10
... the screen on a non-abrasive surface (Figure S.1). To rotate screen, place hands on each side of the monitor. NOTE: In order to avoid stand drop, when removing screws, please support stand with care when monitor facing down on the desk or pinching with one hand, grip the top of the display by the...
User Manual - Page 12
...main and sub-menu, a warning window will appear. DV MODE
Dynamic Visual Mode allows you to increase or decrease the adjustment.
Size and Fine settings. Button
MENU 4-Direction-Key
Left/... control buttons on the front of the monitor function as follows:
To access OSD menu, press any of power consumed by pressing the MENU button. ON: Set brightness variable range from 0% to 60%....
User Manual - Page 13
.... OFF TIMER: Monitor will appear on your screen. When this colour supported environment, the operator could easily and confidently communicate colour without further colour management overhead in colour will automatically power-down simultaneously. OSD LOCK OUT: This control completely locks out access to all OSD control settings back to the factory settings. NOTE: When...
User Manual - Page 14
... Signal window will appear. OSD Warning
OSD Warning menus disappear with Exit button. English-12
The model and serial numbers of the monitor. NO SIGNAL: This function gives a warning when there is turned on the OECD (2006 Edition).
Information
The Information menu indicates the current input, display resolution, horizontal and vertical frequency, and polarity settings...
User Manual - Page 15
...Specifications
Monitor Specifications
MultiSync E222W
Notes
LCD Module
Diagonal: 55.9 cm/22.0 inches
Viewable Image Size: 55.9 cm/22.0 inches
Native Resolution...Resolutions: When resolutions are shown that are subject to 75 Hz
NEC DISPLAY SOLUTIONS cites recommended
1680 x 1050 @ 60 Hz resolution...Image Formation Time
5 ms (Typ.)
Resolutions Supported
720 x 400*1: VGA text
Some systems...
User Manual - Page 16
... your personal preference. VESA Standard Mounting Interface: Allows users to connect their MultiSync monitor to use the entire screen area in use, saving two-thirds of your screen image. conversion factor is approximately 36.7 kg (calculated by NEC for its capabilities (such as screen size and resolutions supported) directly to a lower power consumption level when on...
User Manual - Page 17
... respect to compatibility and recommended settings. • Check the signal cable connector for bent or pushed-in pins.
English-15
Unlike CRT monitors, LCD monitors' image persistence is not in a power-saving mode (touch the keyboard or mouse).
Display image is apparent • Signal cable should be avoided.
English
Troubleshooting
No picture • The...
User Manual - Page 18
...to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. The display you have been developed by users and IT-manufacturers all ...manufacturers all over the world. The requirements included in cooperation with scientists, experts, users as well as EMAS or ISO 14 001. • Restrictions on our natural...
User Manual - Page 19
... and electronic products only applies to the monitor, the Energy Saving mode is activated.
The mark on the environment. All required information concerning the disposal of the product and country-specific information on our following websites:
http://www.nec-display-solutions.com/greencompany/ (in Europe),
http://www.nec-display.com (in Japan) or
http...
NEC E222W Reviews
We have not received any reviews for NEC yet.