NEC E437Q Support and Manuals
Get Help and Manuals for this NEC item
Popular NEC E437Q Manual Pages
External Controls - Page 1
... code ...11 4.4 Delimiter ...12 5. Typical procedure example ...20 6.1. Get Timing Report ...30 10.1 Get Timing Report and Timing reply 30 11. Serial No. & Model Name Read ...32
(1/47) Application...3 II. How to change the "Backlight" setting 20 6.2. Communication specification ...5 3. Message type...13 5.1 Get current Parameter from a monitor 13 5.2 "Get parameter" reply ...14 5.3 Set...
External Controls - Page 5
...Automatic setup * If you need to control the monitor again...code
Asynchronous RS-232C 9600bps 8bits None 1 bit ASCII
3.2 LAN control
(1) Communication system (2) Interface (3) Communication layer
(4) IP address
(5) Port No. Communication specification
3.
And the controller (PC) has to re-connect to change, Please refer "Network settings" on User's manual. 7142 (Fixed)
(Note) The monitor...
External Controls - Page 9
...
ETX
page
Hi Lo Hi Lo MSB
LSB
Refer to section 5.5 "Commands message" for more details.
4) Set Parameter reply
The monitor replies with the status of the "Set parameter" is as follows,
STX
OP code OP code ETX
page
Hi Lo Hi Lo
Refer to the "Message Type" in the "Get parameter message...
External Controls - Page 20
...30h): Message receiver is a sample of "Get
parameter" and "Set parameter".
6.1. Message STX (02h): Start of packet
Step 2.
Delimiter CR (0Dh): End of Message '0'-'0' (30h, 30h): Result code. Monitor ID: Indicate a replying Monitor ID. No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 18 bytes. Typical procedure example
The following is...
External Controls - Page 21
... Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of Message
Check code
BCC: Block Check Code Refer to the section 4.3 "Check code" for confirmation. No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 10h (in the page 0). '0'-'0'-'5'-'0' (30h, 30h, 35h, 30h): Set Backlight setting 80(0050h). Header
Message
SOH-'0'-'0'-
External Controls - Page 28
... off by IR) ETX (03h): End of packet
2) The monitor replies a data for a BCC calculation.
Delimiter CR (0Dh): End of Message
Check code BCC: Block Check Code Refer to change a setting.
No error. 'C'-'2','0'-'3'-'D'-'6' (43h, 32h, 30h, 33h, 44h, 36h): power control reply command The monitor replies same as the power off by IR) ETX (03h...
User Manual English - Page 2
...18 Battery Installation and Replacement English-19 ...NEC product English-41 Energy Saving English-41 Product Specification English-42 Controlling the LCD TV via RS-232C Remote Control English-52 Controlling the LCD TV via LAN Control English-54 Connecting to a Network English-54 Network Setting by Using an HTTP Browser English-54 Supporting HDMI CEC command English-56 Before Calling Service...
User Manual English - Page 6
....
English-4 Many injuries, particularly to children, can be tripped over, pulled or grabbed. • NEVER place a television set in accordance with the installation instructions. WARNING - Stability Hazard A television set may be located between the television set and supporting furniture. • NEVER place items that might tempt children to climb, such as :
• ALWAYS use cabinets or...
User Manual English - Page 9
... persistence, turn off the monitor when not in
cabinet, unless proper ventilation is not permanent, but constant images being displayed for one hour and a residual image remains, the monitor should be avoided.
Unlike CRT monitors, LCD monitors' image persistence is provided.
CAUTION: These servicing instructions are for necessary ventilation. Leave some space around the TV set .
User Manual English - Page 14
...part...manual. If this equipment does cause harmful interference to radio or television reception, which can radiate radio frequency energy and, if not installed...NEC Display Solutions of the following booklet, prepared by the Federal Communications Commission, helpful: "How to Identify and Resolve Radio-TV Interference Problems...E437Q / E327 color monitor so as not to interfere with the instructions...
User Manual English - Page 45
...; This model may not be compatible with Stand and Base: 24.6 kg (54.3 lbs)
without Stand and Base: 23.8 kg (52.5 lbs)
VESA compatible mounting interface
400 mm x 200 mm (M6, VESA hole depth 17 mm)
Plug & Play
VESA DDC2B
Accessories
Remote control (1), 1.5 V AAA batteries (2) Power cord (1) (3.0 m), HDMI cable (1) (2.0m), Setup Manual (1)
NOTE: • All specifications, weights...
User Manual English - Page 47
... 17 mm)
Plug & Play
VESA DDC2B
Accessories
Remote control (1), 1.5 V AAA batteries (2) Power cord (1) (3.0 m), HDMI cable (1) (2.0m), Setup Manual (1)
NOTE: • All specifications, weights, and dimensions are subject to change without prior notice. Please access www.necdisplay.com for detailed specifications and dimensions for custom installations. • This model may be added in the...
User Manual English - Page 49
...; This model may not be compatible with Stand and Base: 12.9 kg (28.4 lbs)
without Stand and Base: 12.4 kg (27.3 lbs)
VESA compatible mounting interface
400 mm x 200 mm (M6, VESA hole depth 17.5 mm)
Plug & Play
VESA DDC2B
Accessories
Remote control (1), 1.5 V AAA batteries (2) Power cord (1) (3.0 m), HDMI cable (1) (2.0m), Setup Manual (1)
NOTE: • All specifications, weights...
User Manual English - Page 58
... able to the user's manual supplied with an HDMI
cable.
Please
refer to cope with "Change Language
function".
English-56 After that the
connected HDMI CEC supported device be turned on the monitor by HDMI cable is set an HDMI CEC audio amplifier between the
monitor and an HDMI CEC supported device with the HDMI CEC...
User Manual English - Page 92
...specific code (or a derivative thereof) from the library being used are not to . this distribution, be it the RC4, RSA, lhash, DES, etc., code; The SSL documentation included with the distribution.
3. Redistributions of source code...as the author of the parts of the library used....SERVICES; i.e. If this package is used in the documentation and/or other materials provided with this code...
NEC E437Q Reviews
We have not received any reviews for NEC yet.