NEC V801-TM Support and Manuals
NEC V801-TM Videos
Popular NEC V801-TM Manual Pages
External Control Codes - Page 3
Application
This document defines the communications method for control of the NEC LCD monitor, MultiSync P402 /P462 /P552 /P702 /V422 /V462 /V551 /V651 /V322 /V652 /V552 /X461S /X551S /X401S /X463UN /X551UN /V463 /V423 /X462S /X552S /X462UNV /V801 when using an external controller.
(3/72) I.
External Control Codes - Page 5
...(2) Interface (3) Baud rate (4) Data length (5) Parity (6) Stop bit (7) Communication code
Asynchronous RS-232C 9600bps 8bits None 1 bit ASCII
3.2 LAN control
(1) Communication system...is received for the LCD monitor.
(5/72) Communication specification
3. The packet interval needs to change, Please refer "Network settings" on User's manual. 7142 (Fixed)
(Note) The monitor will ...
External Control Codes - Page 20
... replies with the current brightness setting and capability
to support this byte is 18 bytes. Message STX (02h): Start of Message
Check code
BCC: Block Check Code Refer to get a value. Delimiter CR (0Dh): End of Message '0'-'0' (30h, 30h): Result code.
No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 10h (in the...
External Control Codes - Page 21
...
BCC
CR
Header SOH (01h): Start Of Header '0' (30h): Reserved '0' (30h): Message receiver is 10 bytes. No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is set to store the Backlight setting. (Save Current Settings Command)
(21/72) Message STX (02h): Start of packet
Delimiter CR
Step 4. Header SOH-'0'-'0'-
Delimiter CR (0Dh...
External Control Codes - Page 23
...code BCC
Header SOH (01h): Start of Message '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'8' (37h, 38h): Operation code...code
BCC: Block Check Code Refer to 'A', the replying Monitor ID is '1'. 'F' (46h): Message Type is "Set... 1.
No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'8' (37h, 38h): Operation code is 78h (in temperature sensors. MultiSync P402 /P462...
External Control Codes - Page 24
...code BCC: Block Check Code Refer to the section 4.5 "Check code" for a BCC calculation.
ETX (03h): End of selected sensor. No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'9' (37h, 39h): Operation code...30h, 32h): Operation code page number is 2. '7'-'9' (37h, 39h): Operation code is 79h (in the page 2). '0'-'0' (30h, 30h): This operation is "Set parameter" type. ...
External Control Codes - Page 26
...: A/V mode only
ISF-Day: ISF-Night: Each needs an adjustment by ISF. Operation Code (OP code) Table
Item
Backlight Contrast Sharpness Brightness Hue Color Color Temperature Color control
Gamma Correction
Movie
Adaptive
Settings Contrast
Noise Reduction
Telecine
Picture mode
OP OP code Parameter
cod
e
pag
e
00h 10h
0: dark
|
100(64h): bright
00h 12h
0: low...
External Control Codes - Page 30
...instruction
manual. OS D
Item
PIP H Position PIP V Position Aspect
Text Ticker
Mode Position Size
Blend Detect Fade In PIP Input(Sub input)
Menu tree reset (PIP) Language
Menu Display Time
OP OP code...(reserved) 0: None 1: Off 2: Horizontal 3: Vertical 0: Top/Left | 100: Bottom/Right 0-1: Do not set. 2: Narrow(2/24) | 8: Wide(8/24) 1: 10% | 10: 100% 0: None 1: Auto 2: Off 0: None 1: On 2: ...
External Control Codes - Page 35
Refer to the monitor
instruction
manual. Momentary
Momentary
This
operation
requires supported
option TV tuner.
2's Read only Read only Read only... 0: | 65535:
Remarks
This operation has
limitation
of
selection.
Item
OP OP code cod e pag e
Parameter
PIP Input
02h 73h
0: No mean 1: VGA 2: RGB/HV 3: DVI 4: HDMI (Set only) 5: Video1 6: Video2 7: S-Video 12(0Ch): DVD/HD1 13(0Dh...
External Control Codes - Page 38
....) The maximum data length that can be written to the section 4.5 "Check code" for confirmation. No error. 'C'-'2','0'-'3'-'D'-'6' (43h, 32h, 30h, 33h, 44h, 36h): power control reply...set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is set . 0004: OFF (same as ASCII characters '2' and '0' (32h and 30h). Message STX (02h): Start of Message
Check code BCC: Block Check Code...
External Control Codes - Page 42
... from top of Message '0'-'0': Result code. Data(N): Asset data. Delimiter
(42/72)
Data(N): Asset data.
Message STX (02h): Start of the Asset data area. No error. 'C'-'0'-'0'-'E' (43h, 30h, 30h...
Check code
BCC: Block Check Code Refer to write Asset data.
ETX (03h): End of packet
2) The monitor replies a data for a BCC calculation. Ex.) When this byte is set to write...
External Control Codes - Page 68
..., then it only checks Pass cords (and releases image muting if Pass codes are matched with them then setting isn't changed, and reply error status and a current condition.
Header
Message
Check
code
SOH-'0'-MonitorID-'0'-'A'-'1'-'0' STX-'C'-'2'-'1'-'D'-EN-P1-P2-P3-P4-ETX BCC
Delimiter CR
Header SOH (01h): Start Of Header '0' (30h): Reserved Monitor ID...
Specification Brochure - Page 1
The V423-TM, V463-TM , V552-TM V652-TM and V801-TM also support Open Pluggable Specification (OPS), the first industry-wide standardization in option slots, simplifying installation, use for various applications • Integrated 10W speakers provide stereo audio for those applications requiring sound • Extensive control, diagnostic and communication provide the highest ...
Specification Brochure - Page 2
...WxHxD) Net Weight (without stand; Specifications
MODEL LCD MODULE
Panel Technology
V423-TM
S-IPS
V463-TM
AMVA
V552-TM
AMVA
V652-TM
AMVA
V801-TM
UV2A
Viewable Image Size Native Resolution Brightness...Control POWER CONSUMPTiON On (Typical) ECO Mode Standby PHYSICAL SPECIFICATIONS Bezel Width (L/R, T/B)
Net Dimensions (without stand) VESA Hole Configuration ENVIRONMENTAL CONDITIONS Operating ...
Mechanical Drawing - Page 1
Model: V801-TM Scale: 1:1 Unit: Inches
500
d Suite 1100
PaIktaBscoau,leILvar6043
Telephone: (630) 467-3000 DISTANCES MAY VARY UP TO 5%. -18.58
ro
UR
if)
rn C
0)
L .L1.3
39....
LUTIONS
NEITHER THIS DESIGN NOR ANY NI FORMATION
CONTAINED IN THIS DRAWING MAY BE
REPRODUCED OR DISCLOSED TO OTHERS
WITHOUT THE EXPRESS WRITTEN CONSENT OF
NEC DISPLAY SOLUTIONS.
NEC V801-TM Reviews
Do you have an experience with the NEC V801-TM that you would like to share?
Earn 750 points for your review!
We have not received any reviews for NEC yet.
Earn 750 points for your review!