NaceCare TTB3226 Support and Manuals
Get Help and Manuals for this NaceCare item
View All Support Options Below
Free NaceCare TTB3226 manuals!
Problems with NaceCare TTB3226?
Ask a Question
Free NaceCare TTB3226 manuals!
Problems with NaceCare TTB3226?
Ask a Question
Popular NaceCare TTB3226 Manual Pages
TTB3226 Owners Manual - Page 1
Read instructions before using the machine. Attention Lisez la notice avant d'utiliser la machine.
www.nacecare.com Owner Instructions Mode d'emploi
TTB 3226
(TRO 650) Charger-less Machine
Original Instructions Warning!
TTB3226 Owners Manual - Page 5
... vibration
10
11 Whole body vibration
11
8
Safety Critical Components
Motor Wheel & modified brake lead assembly (321450)
PPE (Personal Protective Equipment) That may be worn. Specifications
Brush Motors
2 x 24V 400W
Brush Speed
200 rpm
Vac Motor
24V 400W Water
Capacity
31.7 gallon
Power
4 x 12V = 200Ahr
Noise Max decibel level at
1 meter...
TTB3226 Owners Manual - Page 6
... use on the appliance. Use a respiratory mask in good condition. When replacing major components the ignition key and battery fuses MUST be used or stored outdoors or in the instruction manual. rings, chains etc. The fitting of any worn or damaged parts immediately. The batteries must be removed from the machine before it is...
TTB3226 Owners Manual - Page 9
Quick Set Up Guide
! After the removal of all the packaging, carefully open and check the contents of the pallet using the ramp provided (Fig.5). Note: Ensure that no metal objects come into ignition and turn quarter-turn key back to the off of the start -up pack (Fig.1).
!
1
Contents: 1 x Operator Manual 2 x Keys 3 x 40...
TTB3226 Owners Manual - Page 10
Replace as shown above. ensure a tight fit (Fig.9).
ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF BEFORE MAKING ANY ADJUSTMENTS
!
...the floor tool
Fig.9
Fig.7
Fig.8
Lower the floor-tool arm by moving the release lever to the pod (Fig.6a). Machine Set Up
!
Fitting the side pod skirts
Fig.6a
Fig.6b
To fit the side pod skirts, first remove the steel retaining strip already ...
TTB3226 Owners Manual - Page 11
... chucks making fitting and removal a simple process. Fig.13
Filling the clean water tank
The TTB 3226 is always clean and free from debris. Machine Set Up
Fitting the brushes
Fig.10
Fig.11
Fig.12
Featuring the new OBS (Octagonal Brush System); Close side pod (Fig.13).
Fig.16a
11...
TTB3226 Owners Manual - Page 12
... the Operator Manual has been read and fully understood.
!
Before performing the cleaning operation, place out appropriate warning signs and sweep or dust-mop the floor. Lowering the brush deck
Fig.20
Fig.21
Fig.22
After preparing the floor (see previous section), we are now ready to set -up guide if necessary...
TTB3226 Owners Manual - Page 13
... 'ON' position (1). Lowering the Floor-tool
Fig.23
Lower the floor-tool by using the lever found on the left-hand side (see Fig.24).
Setting the cleaning controls
Insert the key into the ignition and quarter-turn it clockwise to the upper position (Fig.23). The battery charge-level indicator...
TTB3226 Owners Manual - Page 14
... clockwise (see Fig.25). After resetting the emergency stop automatically.
If the brush load increases due to changing floor types, the pressure can be adjusted manually by the operator using the adjuster knob found on the operator control panel (as illustrated) and the vacuum motor will stop button, to the off...
TTB3226 Owners Manual - Page 16
... will switch the vacuum off. Maximum Speed Control
Use the maximum speed control knob and set using the variable control speed pedal located on the control panel, fine adjustments can be made.... Pressing the Off aisle Button again will NOT illuminate Blue.
Once the Max speed has been set desired traction speed as required, depending on floor type and level of capacity and the Hi -...
TTB3226 Owners Manual - Page 19
...4 3
Note:
4 5
Floor Tool adjusters are designed to be examined and checked for optimal performance. The blades are factory set for wear and damage. Changing the Floor Tool Blades
!
Simply start by removing the four retaining pins (see Fig.38), turn...Fig.39).Peel away the blades from the rear of the removal process. Replacement is a reversal of the machine. Front blade (slotted)
5.
TTB3226 Owners Manual - Page 22
...voltage and charge current ensuring charger red fault light is extinguished.
Contact Service Agent
Check connections on Product
Operating time severely reduced or machine will...Action Required Charge batteries immediately
If fault persists
Tighten loose connections and replace damaged components
Replace batteries as necessary. Green Flashing Warning light.
22
Green Status Indicator ...
TTB3226 Owners Manual - Page 23
... recharging. * Faulty cell on battery
Effect on * Release emergency stop pressed
* Vac.
B = Brush total run -time. Contact Service Agent.
23
LCD Display
LCD Display Blank 'OVER CURRENT'
'UNDER VOLTS' ' TANK FULL' 'INHIBITED'
Fault * No power
* .../ pump will not operate. *Key switched off * Emergency stop
* Charge Batteries. * Replace battery (if cell damaged)
* Empty Waste (Top) Tank...
TTB3226 Owners Manual - Page 24
Trouble-Shooting
PROBLEM
Machine ...-water tank filter blocked/ clogged Incorrect water flow setting Brush deck raised
Too much load on the brush system
SOLUTION
Fit or replace fuse (page 9) Turn key to 'ON' ...and clean (Page 17) Clean and refit (page 17) Renew (contact service dept) Renew (contact service dept) Renew (contact service dept) Recharge batteries
Check and fit (page 11) Lower brush deck ...
TTB3226 Owners Manual - Page 41
...) (Front) 606295 - Splash Skirt Fixing Strap BRUSHES: 606174 - Spare Keys
Recommended Spare Parts Pièces de rechange conseillées
208163 - Gas Strut 229834 - Amer Drive Wheel... BLADES: 208640 - Linatex Blade Set (750mm) LINATEX BLADE FLOOR TOOLS: 606298 - Poly Blade (750mm) (Rear) 208641 - Poly Blade (750mm) (Front) 606296 - Poly Blade Set (750mm) POLY BLADE FLOOR TOOLS...
NaceCare TTB3226 Reviews
We have not received any reviews for NaceCare yet.