Netgear WAG302NA - WAG302.PROSAFE 11ABG Dual Band Wireless Access Point Support and Manuals
Get Help and Manuals for this Netgear item
View All Support Options Below
Free Netgear WAG302NA manuals!
Problems with Netgear WAG302NA?
Ask a Question
Free Netgear WAG302NA manuals!
Problems with Netgear WAG302NA?
Ask a Question
Popular Netgear WAG302NA Manual Pages
Reference Manual - Page 16
... IP address to -Point Bridge. AutoCell provides advanced automated RF management that improves performance and enhances security.
• Multiple Operating Modes - WEP should be upgraded remotely.
2-2
Introduction
202-10078-01 Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
Key Features
The WAG302 Access Point is easy-to -Multi-Point Bridge. Support...
Reference Manual - Page 31
...LAN.
- Country/Region: This field identifies the region where the WAG302 can use this IP address default gateway for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
-
Default Gateway Address: The Access Point will automatically calculate the subnet mask based on your country or region from the drop-down list. Basic Installation and Configuration
3-9
202-10078-01
Reference Manual - Page 33
... dynamic IP addresses, you will deploy it where you will need to browse the Internet, or check for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
Now that they are vertical. d. Connect the power adapter to the wireless access point and plug the power adapter in step 1 back to a LAN port on either side so that you have finished the setup...
Reference Manual - Page 34
... Explorer or Netscape Navigator. 3. The WAG302 is the default IP address of your access point. Note: The computer you have entered your access point name, your Web browser should be configured with an IP address that starts with the DHCP client disabled.
Enter admin for the user name and password for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
How to Log In to the...
Reference Manual - Page 52
...; The IP Address The wireless access point is under the Basic heading of the main menu. IP Subnet Mask - 255.255.255.0 - Gateway - 0.0.0.0 - Primary and Secondary DNS Servers - 0.0.0.0
3-30
202-10078-01
Basic Installation and Configuration Figure 3-16: IP Settings menu
• Access Point Name (NetBIOS) Enter a new name for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
Using...
Reference Manual - Page 56
Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
• SNMP - Using the Secure Telnet Interface
The WAG302 includes a secure Telnet command line interface (CLI).
Using the null-modem cable, connect a VT100/ANSI terminal or a workstation to read the wireless access point's MIB objects. The default is Private. -
Also, when you configure the client...
Reference Manual - Page 60
...Current IP Settings
IP Address Subnet Mask Default Gateway DHCP Client
The IP address of the firmware currently installed. Enabled indicates that the current IP address was obtained from a DHCP server on page B-7 for the frequencies used by the wireless port of the wireless access point's Ethernet port. Displays the wireless network name (SSID) being used
on each channel.
Reference Manual...
Reference Manual - Page 61
...802.11 operating mode of the WAG302: Access Point, Point-to-point bridge, Multi-point bridge or Repeater. The default is the default channel
setting. See "Wireless Channels" on page B-7 for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
Table 4-1. WEP/WPA setting.
Identifies the channel the wireless port is using. 11 is NETGEAR_11g. Reference Manual for the frequencies used by...
Reference Manual - Page 83
... the wireless access point correctly? If you are using the correct NETGEAR power adapter supplied with your WAG302 ProSafe Dual Band Wireless Access Point.
After each problem description, instructions are lit on . Chapter 6 Troubleshooting
This chapter provides information about troubleshooting your access point.
For the common problems listed, go to the access point. •...
Reference Manual - Page 84
... that network. Reference Manual for that TCP/IP is set up properly for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
The Wireless LAN activity light does not light up.
Use a standard Category 5 Ethernet patch cable. The usual setting for Windows the Network Properties is set to "Obtain an IP address automatically."
• The access point's default values may not...
Reference Manual - Page 114
... it with the host's IP address. The assigned information includes IP addresses, DNS addresses, and gateway (router) addresses. CAs are security issues with an RJ45 type connector. Auto Uplink Auto UplinkTM technology (also called a DLC address), such as an Ethernet address. Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
ARP Address Resolution Protocol, a TCP...
Reference Manual - Page 115
... rate).
The assigned information includes IP addresses, DNS addresses, and gateway (router) addresses. Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
DNS Short for Domain Name System (or Service), an Internet service that translates domain names into the corresponding IP address. ESSID The Extended Service Set Identification (ESSID) is really based...
Reference Manual - Page 116
...service provider.
See also Auto Uplink.
-4
Glossary
202-10078-01 IP Address...At the hub, switch, router, or access point, the perspective is called...IP. Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
IP Internet Protocol is the main internetworking protocol used in the Internet.
In MDI wiring, a PC transmits on pins 1 and 2. Ranges of addresses...
Reference Manual - Page 117
... where each station is given a name. Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
NAT A technique by a working group of the IETF.
netmask Combined with one another so that network.
Though not an official standard, the RADIUS specification is the host address on IP source and destination addresses. An IP router forwards data based on that they can...
Reference Manual - Page 118
...Wi-Fi A trade name for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
SSID A Service Set Identification is the TLS Handshake Protocol, which must be reached through a gateway or router. For the wireless devices in the wireless Access Point and to communicate with each other, all devices must be configured with the IP address, the IP Subnet Mask allows a device to know...
Netgear WAG302NA Reviews
We have not received any reviews for Netgear yet.