Oki GL412e Support and Manuals
Get Help and Manuals for this Oki Data item
Popular Oki GL412e Manual Pages
GL408e/GL412e User's Guide - Page 25
... change the setup, enter "root" user and password at 80 ma
LOCAL AREA NETWORK (LAN) ETHERNET
A Local Area Network (LAN) interface is possible to 127 devices may be sent by the user. It requires a driver shipped with a LAN Optional interface installed. In addition, if the banner page is shipped with each printer with each printer with a proper setup. Job deletion...
GL408e/GL412e User's Guide - Page 51
... required to correlate the printer's interpreter language with that of Measure Row Offset Column Offset Format Attrib. POWER
ONLINE
LINE
OFFLINE
FUNCTION
EMULATION
Emulation Mode ENTER
EMULATION Select
Select DGL*
DGL Setup
Active Character Set Euro Character Control Codes FeedBack Chars Default Module Units of Datamax interpretor language. XOR*
Error Handling Off*
Vert. Refer...
GL408e/GL412e User's Guide - Page 54
... only display if Admin User is enabled within the
Advanced Mode
ENTER
DIAGNOSTICS
Priority Setting Printer Tests Test Count Software Build Hex Dump Mode Print Error Log Clear Error Log Flash Installed DRAM Installed Ptr On Time Printer Usage PrintHead Usage Head On Time Reset Head Data PrintHead Usage Head Type Head Voltage
ENTER
Priority Setting Command*
Printer Tests Checkerboard*
Software...
GL408e/GL412e User's Guide - Page 57
... change under normal circumstances.
OFFLINE
+ ENTER ENTER SWITCH LOCKED
+ ENTER ENTER SWITCH UNLOCKED
GL408-412e Operator Manual
Figure 4-20, Key Lock/Unlock 4-21
PN: 9001163A If the reset is locked to prevent change , it will not erase any settings previously saved to an online state. Unit 4: Printer Configuration
SOFT RESET
Reboots the printer back to non-volatile memory.
GL408e/GL412e User's Guide - Page 60
... corner.
• Inv.
If the operator panel selection is to encode C128 bar code data using automatic mode switching. DPI Adjust 0*
C128 Mode Switch Manual*
Error Handling Beep*
Mem Select (CC1) Card*
Orientation Portrait*
Unit 4: Printer Configuration
USER MODE (TABLE 4-1) DESCRIPTION
This setting changes the vertical base reference point for the current label job and all subsequent...
GL408e/GL412e User's Guide - Page 62
... back after a label has been removed in the Sensor Setup menu of the Advanced Mode. MENU
Ribbon Near End Enable*
Units In Millimeters*
Set Label Length Manual*
TOF Detect Fault 3 labels*
TOF Adjust Mode Disable*
TOF Adjust 10.1 mm*
MENU
CONFIG MODE
Unit 4: Printer Configuration
USER MODE (TABLE 4-1)
DESCRIPTION
When enabled and the amount of...
GL408e/GL412e User's Guide - Page 63
... requirements. GL408-412e Operator Manual
4-27
PN: 9001163A Print Config. Factory*
Loading Factory Configuration
Unit 4: Printer Configuration
CONFIGURATION MODE (TABLE 4-2) DESCRIPTION
Is the menu selection screen for the CONFIGURATION Mode. The factory default is 1. Power-Up Config. This menu set allows the selection and loading of a specific configuration. Is an informational...
GL408e/GL412e User's Guide - Page 66
... printing the next label. This option is installed. Permits selection of the Advanced Mode. This method is only supported whenthe Value Peel or the PeelOff Rewinder option is used for each printed label/tag or following a specified quantity. Intensity Sensor Setup Admin User
Media Handling Continuous*
Unit 4: Printer Configuration
ADVANCED MODE (TABLE 4-3) DESCRIPTION
Is the...
GL408e/GL412e User's Guide - Page 75
.... This resolves problems where the sensors...value set in the USER MODE is used for most cases this range is performed. This option allows the user to ...Printer Configuration
ADVANCED MODE (TABLE 4-3)
DESCRIPTION
Determines if the Label Length value set in the Media Setup menu is 50% with an allowable range of 5 to 95% in 5% increments. Run a Media Profile after doing an Auto or Manual...
GL408e/GL412e User's Guide - Page 109
... characters are not sent to set desired for the printer to use to represent the Euro character. GL408-412e Operator Manual
4-73
PN: 9001163A Allows selection of the control codes. Select the ASCII character (in the command. • RAM - Storage in volatile RAM where the data will remain unless actively removed. Switch (V) Sensor Cmd (e,r) Format Attr...
GL408e/GL412e User's Guide - Page 118
... Hex Dump Mode Print Error Log Clear Error Log Flash Installed DRAM Installed Ptr On Time Printer Usage PrintHead Usage Head On Time Reset Head Data PrintHead Usage Head Type Head Voltage
Priority Setting Command*
Is the menu selection screen for printing. DIAGNOSTICS MODE (TABLE 4-15) DESCRIPTION
Permits entry into the DIAGNOSTICS Mode. MENU
IGL Setup Save state*
MENU
DIAGNOSTICS...
GL408e/GL412e User's Guide - Page 124
... Configuration
QUICK MENUS (TABLES 4-17 THROUGH 4-20) DESCRIPTION
Indicates the printer has been removed from the online status. Indicates the printer is complete.
SOFT RESET
ENTER SWITCH LOCKED
ENTER SWITCH UNLOCKED
Is an informational menu screen that displays when the printer's internal buffer has been cleared of the LCD decrease or inceases respectively.
By pressing the left or...
GL408e/GL412e User's Guide - Page 130
...
enabled in the up position and If the error persists, contact an authorized
the cutter upper enclosure installed. The print head has become overheated. If the problem persists, contact an authorized customer service representative. Power off the printer for 5 minutes, then press the Pause key.
Unit 5: Troubleshooting
ERROR SIGNALS
DISPLAY
MEDIA OUT Load Media
MEDIA OUT...
GL408e/GL412e User's Guide - Page 134
... within this manual for instructions. RS232 SERIAL INTERFACE
CHK
TROUBLESHOOTING STEP
Ensure the correct interface module is correctly installed. Refer to that procedure within the new window. The command stream should be the problem.
PARALLEL INTERFACE
CHK
TROUBLESHOOTING STEP
Ensure the interface module is correctly installed.
Ensure the host's peripheral settings are...
GL408e/GL412e User's Guide - Page 136
... User is numbered. The contents of data received is enabled within the
Advanced Mode
ENTER
DIAGNOSTICS
Priority Setting Printer Tests Test Count Software Build Hex Dump Mode Print Error Log Clear Error Log Flash Installed DRAM Installed Ptr On Time Printer Usage PrintHead Usage Head On Time Reset Head Data PrintHead Usage Head Type Head Voltage
ENTER
Priority Setting Command*
Printer Tests...
Oki GL412e Reviews
We have not received any reviews for Oki yet.