Optoma HD82 Support and Manuals
Optoma HD82 Videos
Popular Optoma HD82 Manual Pages
User Manual - Page 1
...
How to operate ...21 Menu Tree...22 Image...23 Display ...28 System...31 Setup...35
Appendices 38 Troubleshooting 38
Image Problems 38 Other Problems 39 Projector Status Indication 40 Remote Control Problems 41 Replacing the Lamp 42 Compatibility Modes 44 RS232 Commands and Protocol Function List 45 Ceiling Mount Installation 48 Optoma Global Offices 49 Regulation & Safety Notices 51...
User Manual - Page 3
... local reseller or service center to cool down .
Allow 90 seconds for the projector to change the lamp when it shows warning messages.
the end of its life time, the message "Replacement suggested" will show on the screen. The bright light may cause electric shock.
Follow instructions as recommended in operation. This projector will not turn...
User Manual - Page 6
...POWER LAMP TEMP
STANDBY
Noottee
Projector with lens cap
Due to ensure all parts ...Image Shift Source
Backup Remote Control
2 x AA Batteries
CR2025 3V
Backup Remote Battery 12V Trigger Connector
(EMEA/USA*2, ASIA*1)
Documentation :
User's Manual Warranty Card Quick Start Card WEEE Card
If something is missing, please contact Optoma customer service...
User Manual - Page 13
... source that the "Source Lock" has been set to "Off".
▀■ If you want to display on the remote control to "SETUP". If not, push menu button and go to switch between inputs. English
Installation
Powering On/Off the Projector
Powering On the Projector
1. Turn on the lamp by pressing " " button on the side of...
User Manual - Page 14
... on
49 for more information. Contact the nearest service center if the projector displays these
▀■
When the "TEMP" indicator turns red, tor has overheated. Once in 5 seconds.
2.
symptoms. See page
Under normal conditions, the projector can be switched on , you wish to restart the projector.
3. Installation
Powering off procedure. First push of the...
User Manual - Page 16
Installation
Adjusting Projected Image Position Using PureShift
Horizontal Lens Shift Lever
Vertical Lens Shift Lever
The PureShift feature provides a lens shift function that can be used to achieve the maximum vertical image position height detailed above if the horizontal image position is at 5% of the image height above the centre of the projector lens. For example it...
User Manual - Page 19
... User. Refer to page 26)
/ Brite Mode
Increase the brightness of the image.
Contrast
Control the degree of difference between the lightest and darkest parts of the image to be shown in incredible detail. (refer to the "Power Off the Projector" section on page 13. Menu
Display or exit the on each edge of...
User Manual - Page 21
... close and the projector will automatically detect
the source. How to operate
1. To open the OSD menu, press "Menu" on a particular page, press
or "Enter" key to enter sub menu.
3. Use by
keys to select the desired item and adjust the settings key.
4. Select the next item to make image adjustments and change...
User Manual - Page 25
... among the pre-sets to obtain different image effects. (Off/On)
Color Temp
If set to set to warm temperature, the image tends to automatically increase the contrast of visible noise interlaced signals. English
User Controls
Image | Advanced
Noise Reduction
The motion Adaptive Noise Reduction reduces the amount of input image. After the initial setup and fine tuning...
User Manual - Page 27
PureEngine Demo
This feature enables you make to see the difference in the image quality between the raw unprocessed image and the image processed as processed by the PureEngine. Use this mode to check the adjustments that you to the PureEngine settings.
27
The range is preserved. PureColor
This adjustable item utilizes a new color-processing algorithm...
User Manual - Page 29
...image will be black bars around the image in 16:9 mode.
ent setting...Lamp power and vertical resolution are not enhanced for 16x9 Display in a video image. V Keystone
Press the or to magnify an image on the projection screen. Overscan the image to fill the image on the edge of an image. Press the to adjust image distortion vertically and make a squarer image... support ...
User Manual - Page 37
.... Press the to decrease the amount of color in the image.
IRE : Adjust measurement of red in the image. Reset
Return the adjustments and settings to factory default values.
Current : Return the current menu's settings to factory default. All : Return the settings for all menus to increase the amount of composite video...
User Manual - Page 38
Please
refer to the "Replacing the Lamp" section.
Make sure you experience a problem with your projector, please refer to the following :
Please setup the display format as described in
projector OSD.
If the image is removed. Adjust the Focus Ring on
your local reseller or service center. Appendices
Troubleshooting
If you have removed the lens cap...
User Manual - Page 39
.... To replace the lamp, follow the procedures in the "Replacing the Lamp" section on page 42.
39 Image is reversed
Select "System-->Projection" from the screen. Press [Menu] on the projector panel, go to "Display-->Format". If this happens, the projector will burn out and may
make an adjustment. Try
the different settings. English
Appendices
Image is...
User Manual - Page 47
...Image AI
n=On/Off (a-31/32)
~XX108 1
7E 30 30 31 30 38 20 31 0D
Lamp Setting
Lamp Hour
~XX109 1
7E 30 30 31 30 39 20 31 0D
Lamp...Lamp...projector automatically
232 ASCII Code HEX Code
Function
Projector...Lamp fail
INFOn
n : 0/1/2/3/4 = Standby/Warming/Cooling/Lamp fail
READ from projector
232 ASCII Code HEX Code
Function
Projector...Off/On
bbbb: Lamp Hour
c: source ...
Optoma HD82 Reviews
Do you have an experience with the Optoma HD82 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Optoma yet.
Earn 750 points for your review!