Panasonic AWRP120 Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic AWRP120 manuals!
Problems with Panasonic AWRP120?
Ask a Question
Free Panasonic AWRP120 manuals!
Problems with Panasonic AWRP120?
Ask a Question
Popular Panasonic AWRP120 Manual Pages
AWRP120 User Guide - Page 1
... the time to read through to ensure that the unit will be installed correctly. (this manual): This describes how to operate the unit and how to establish its settings.
Operating Instructions
Remote Camera Controller
Model No. AW‑RP120G
REMOTE CAMERA CONTROLLER AW-RP120
How the Operating Instructions are configured : The describes the procedure for connection with the...
AWRP120 User Guide - Page 5
... adjustment section is disabled.
Press the button to "FullAuto", the following settings and adjustments can be made for the camera output images at that time but instead is reflected when manual iris (when the auto iris indicator turns off , operation of AW‑HE2" (page 51).
5
Making image adjustments for the selected remote...
AWRP120 User Guide - Page 10
... the unit and the setting
values of the USER buttons (USER 1 to USER 8). The following shows the menu display on the unit
ND1 ND2 ND3 ND4
Remote camera setting values
AW‑HE120
AK‑HC1500 AK‑HC1800
AW‑HE50 AW‑HE60 AW‑HE100 AW‑HE870 AW‑E860 AW‑E750 AW‑E650 AW‑E350
(*)
Through...
AWRP120 User Guide - Page 11
...model.
11 Press the EXIT button. AK‑HC1500 AK‑HC1800 AW‑HE870
AW‑E350 AW‑E650 AW‑E750 AW‑E860 AW...Instructions for example, another remote camera controller or a wireless remote controller. Turn counterclockwise : Changes the setting...manual). Confirms the change to be operated. zzChanges the setting directly (*3). Turn clockwise
: Changes the setting ...
AWRP120 User Guide - Page 12
...AW‑HE50, AW‑HE60, AW‑HE120
The indicators of the number button that which results from the unit. zzPreset numbers PMEM 1 to 10 are also used as at the time of registration are registered to 100 preset memory for the corresponding model. For details, check the Operating Instructions for each camera. MEM SETTING... settings (manual iris only) zzWhite balance settings zzGain...
AWRP120 User Guide - Page 14
...;
MODE B
√
√
MODE C
√
-
zzMove at the common PRESET SPEED set to "On" and the preset memory is recalled on a controller other than the AW‑RP120 on the unit is displayed. Setting the speed at which to move to the position set in the preset memory (PRESET SPEED)
The speed (PRESET SPEED) at...
AWRP120 User Guide - Page 31
... to be linked to one of the switcher
Refer to one AW‑RP120 or AW‑RP50 can be set "SWLINK". INPUT1 to confirm the
selection.
31 Turn the F2...Instructions for the switcher.
„„Registering the camera numbers that is outputting images of [10.5] DVI‑IN in advance.
„„Settings for linking with an optional switcher. Press the MENU button.
2. Open USER...
AWRP120 User Guide - Page 43
...24 V)
GPI OUT (Max. Withstand voltage: Max. 24 V DC Current: Max. 50 mA
AW‑RP120
(Max. current 50 mA)
GND
Example of GPI OUT1 to GPI OUT4
GPI OUT1
GPI OUT2
...28)
Contact input (Trigger operation) zzTrigger width
30 ms
9
GPI IN 6
Control of MENU CONTROL settings ⇒ "Enabling or disabling menu operation" (page 28)
22
GND
GND
10
GPI OUT 1
Remote camera ...
AWRP120 User Guide - Page 45
... the devices (remote cameras, switcher, etc.) connected within the same subnet.
: Set the same subnet mask as that set on the unit. : Set the same default gateway as that is going to install Setup Software.
1. zzDo not perform any operation on the unit, refer to the hard disk drive of the personal computer. 3. IP address Subnet...
AWRP120 User Guide - Page 47
... this manual.
Up to be registered.
1.
In the list box on the "Setting" tab.
47 The settings configured on the selected unit are displayed on the "Setting" tab, select the AW‑RP120
whose data is to register.
2. In the RP1 to RP5 boxes, enter the IP addresses of the AW‑RP120 to be selected from Setup Software. If...
AWRP120 User Guide - Page 49
... numbers and switcher) corresponding to 65535 zzSet 10 port numbers because update notifications are displayed in yellow. When a connection type is selected on the "Setting" tab.
49 Setup Software (continued)
12
13
14
15
16
17
18
19
12 RECEIVE PORT NO Set the port numbers for the remote cameras belonging to the personal computer...
AWRP120 User Guide - Page 50
..., enter the password set . 3. Entered characters are displayed as you can still configure the settings again by default.
2. zzEven if you have the user authentication function enabled, you need to the
Operating Instructions for the remote cameras.
1. Click the [REFRESH] button.
zz"12345" is set on the unit. The user name set by default.
4. Setup Software (continued) Setting user...
AWRP120 User Guide - Page 55
...CAM100
...
...
[44]
TALLY
100. INITIALIZE 2. CAM1
Remote camera
Initial value on unit (*1)
Setting
...
...
[39]
MANUAL IP
100. CAM100 1. CAMINF_CNAME 11. INPUT4 5. INPUT100 1. FPGA VER 1. Table of setting items (menus) (continued)
Button number
[38]
Menu name SWAP IP
Setting item 1. CAM100 1. BUS 4. FOCUS ASSIST 5. CAMINF_IRIS 15. INPUT2 3. TALLY IN1
NoAsign CAM1...
AWRP120 User Guide - Page 56
...reboot AW‑RP120
...LOCKED! The unit needs to the selected number button. The recording standby state of tracing memory.
The recording operation wait state of tracing memory.
Recording tracing memory.
IP connection settings Indication
Unavailable network setting
IP Duplicate! Description
Preset memory registration has completed.
zzA number is a duplicate of the IP address set...
AWRP120 User Guide - Page 57
.... zzA file containing corrupted data
Setup software Indication
Not connected.
Old User Name or Old Password is incorrect.
Complete the "New Password" field.
NOT REMOVE CARD SAVING...
INSUFFICIENT CAPACITY!
Do not remove the memory card.
Already assigned. Please reboot AW‑RP120. Password entered in the "Old User Name" box. The entered information includes...
Panasonic AWRP120 Reviews
We have not received any reviews for Panasonic yet.