Panasonic EYFMA2C Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic EYFMA2C manuals!
Problems with Panasonic EYFMA2C?
Ask a Question
Free Panasonic EYFMA2C manuals!
Problems with Panasonic EYFMA2C?
Ask a Question
Popular Panasonic EYFMA2C Manual Pages
Owner s Manual - Page 12
... Reverse lever when the trigger switch is on steady.
8) Check for damaged parts. • Check thoroughly for service and repair.
11) To avoid potential injury, keep face and hands away from the ...result in for damage to the protective cover and other parts, please follow the instructions in the area where you are no instructions in the manual, please take it around.
6) Make certain that ...
Owner s Manual - Page 13
...Panasonic is not responsible for any damage or accident caused by the use of recycled or counterfeit battery pack.
••Do not dispose of injury, user must read and understand instruction manual...8226;When the Battery Pack Has Deteriorated, Replace It with attachments designed for power tools...CAUTION:
Make sure that there is designed specifically for hand tools may overheat, catch ...
Owner s Manual - Page 15
...Fig.15]
CAUTION:
When storing or carrying the tool, set the Forward/Reverse lever to operate the tool, even within...Fig.14]
The remote control should be operated within this range.
-
Replace it with a fresh battery.
• The included battery is used with...receiver on the fastener as it locks into contact with the Panasonic EYF series assembly tools, make sure the tool's trigger switch...
Owner s Manual - Page 19
..."L7."
• Changing the snug point detection level from "L1" to change .
Model
EYFLA4 EYFLA5 EYFLA7 EYFLA8 EYFLA9 EYFMA2
Number of torque stages setting 1 to 8 1 to 3 1 to 40 1 to 40 1 to 40 1 ...
• If the tool stops before the snug point at snug point detection level "L1," set as shown below, the snug point detection level cannot be displayed.
3. Snug point detection level ...
Owner s Manual - Page 20
... button to accept the new setting. EN Rundown error detecting function (EYFLA7, EYFLA8, EYFLA9, EYFMA2)
The rundown error detecting function causes a red indicator to flash if work ends more information about how to register the tool and Assembly Qualifier, see the Assembly Qualifier instruction manual. This feature is ON, the set tightening time, and the main...
Owner s Manual - Page 23
... lamp: The upper and lower bars of shipment from the factory.
• The error display will begin flashing.
Battery indication lamp: The upper bar of drive component parts (hammer, etc.) used to be turned off .
CAUTION:
The torque set status cannot be checked when the tool panel is not intended to identify the...
Owner s Manual - Page 24
... are displayed in sequence. For example, when the tilt tightening reduction feature is enabled, the repeat tightening prevention is set to 0.5 seconds, and the impact speed corresponding to length of socket used is set to h1, the display is as follows: "H9" → "R1" → "U2"→ "h1"
Display H7 H8 H9...
Owner s Manual - Page 25
... Qualifier closer to the main unit before resuming use
• The battery pack is installed properly to the tool. Please check the tool or battery pack as described in the following use . Display
Likely cause
Corrective action
Setting error
Re-initialize the tool using the tool immediately. The contacts that the Assembly Qualifier...
Owner s Manual - Page 26
...; If the battery pack is not connected firmly when the switch is switched on how to recycle this battery.
[Battery Charger]
Charging
Read the operating manual for Panasonic battery charger for the battery pack before charging.
Owner s Manual - Page 27
VIII. SPECIFICATIONS
EN
MAIN UNIT
Model
EYFLA4 A,AR
EYFLA5
EYFLA6
A
AR P,Q PR,QR J,P
JR,PR
Motor Chuck size
Single-ended 9 - 9.5... lbs)
1.15 kg (2.5 lbs) 1.15 kg 1.2 kg 1.15 kg 1.2 kg 1.25 kg (2.8 lbs) (2.5 lbs) (2.6 lbs) (2.5 lbs) (2.6 lbs)
Model
EYFLA7
EYFLA8
EYFLA9
EYFMA1
EYFMA2
A,AR A,AR C,CR P,PR C,CR P,PR J,JR P,PR C,CR P,PR
Motor Chuck size
Single-ended 9 - 9.5 mm (23/...
Owner s Manual - Page 28
..., if not installed and used in accordance with Part 15 of the FCC Rules. EN BATTERY PACK (not included with shipment)
Model
EYFB30
EYFB32
EYFB41
Storage battery
Li-ion battery
Battery voltage
10.8 V DC
10.8 V DC
14.4 V DC
(3.6 V/6 cells) (3.6 V/3 cells) (3.6 V/4 cells)
EYFB42
14.4 V DC (3.6 V/8 cells)
BATTERY CHARGER (not included with the instructions, may cause...
Owner s Manual - Page 29
... lbs)
Radio Information
Model Indoor/Urban Range Outdoor RF line-of the Assembly Qualifier. IX. Remote control (not included with shipment)
EN
Model
EYFA31
Battery voltage
... FCC Part 15.249 Industry Canada
EYFLA 100 ft./ 30 m 300 ft./100 m 1 mW (0 dBm) -92 dBm (1% packet error) O4O...thus should not be used for human safety-related services. HARMONIZED STANDARDS
MAIN UNIT
Conforms to UL Std....
AccuPulse HR Series Brochure - Page 2
...P = 1/2" Sq. lbs. 185Nm M16 Bolt L1 - AccuPulse HR Series
MODELS
EYFLA7A
EYFLA8A / EYFLA8C / EYFLA8P
EYFLA9C / EYFLA9P
EYFMA2C / EYFMA2P
Voltage Series
10.8V
Drive
A = 1/4" Hex Quick Change
Nm...panasonic.com/assemblytools or call 1-800-338-0552
PESNA_PT_001 lbs
53.1-265.52 in .
Max Torque* (F mode, tightening 3 sec.)
Flush Detection Modes
No Load Speed (Torque Setting...
AccuPulse HR Series Brochure - Page 3
...this time period.
Rehit prevention is defined in 10,000 increment cycle. (Number of setting: 0-990,000 pcs)
Flush Detection Delay
This feature delays Flush Detection mode and ignores ...within a selected time period after it automatically stops from further use.
CLICK! normal time setting
OK
3.0sec. Cross thread
360° reverse rotation before the programmable minimum runtime, the...
AccuPulse HR Series Brochure - Page 4
... remaining battery capacity, minimizing variation in torque. Select higher Snug Torque Detection Mode setting (L3~L7)
Snug Point
Time
Target Shut-off
Snug Point
Pulse
If the ...battery power becomes too low to charge reminder
Battery Capacity
Auto battery Shut Down indication
Setting torque
EYFLA9, EYFMA2 Consistent torque
Tool without Consistent Pulse Control
Auto Battery Shut Down ...
Panasonic EYFMA2C Reviews
We have not received any reviews for Panasonic yet.