Philips RFX9400 - Pronto - Remote Control Extender Support and Manuals
Get Help and Manuals for this Phillips item
View All Support Options Below
Free Philips RFX9400 manuals!
Problems with Philips RFX9400?
Ask a Question
Free Philips RFX9400 manuals!
Problems with Philips RFX9400?
Ask a Question
Popular Philips RFX9400 Manual Pages
Leaflet - Page 1
... easy set-up to 16 extenders can be incorporated in one system.
True multiroom control • No limitation in range with four individually addressable IR outputs. Philips Pronto Wireless Extender
RFX9400
Designed by installers, made by Philips
The wireless extender is a compact unit with use • Compact table-top housing • Smart feedback indicators for easy troubleshooting It...
Leaflet - Page 2
... 6 09585 11126 4
© 2009 Koninklijke Philips Electronics N.V. Specifications are limited to 125 kHz, the Pronto extenders can be executed. Without addressable IR codes, every device will be informed in stand alone mode and requires no special settings.
Where many remote control systems are subject to 1 MHz.
When encryption or fixed IP is desired, the internal web browser is...
User manual - Page 4
RRFXF9X4090 S4t0ar0ter'Ss Gtuaidreter's Guide
Contents
Before You Start 2 Unpacking the Extender 3 Configuring the Extender 4
Stand-alone Connection 4 Network Connection 4 Installing the Extender 6 Connecting the Extender to AV-equipment 6
Support 7 Troubleshooting 7 Firmware Update 9
Specifications 10
IFU Approbation / Safety Content RFX9400 i FCC Compliancy i Regulations According...
User manual - Page 5
... IP address, which enlarges the range of the Pronto System. • When using a dedicated Pronto Network, the Extender can be encrypted. Note An Extender that has been configured in Stand-alone Mode can always be configured in a wireless Pronto Network: • Configure the Extender: connect it to the PC and use up to 16 different Extenders in Network Mode. ENGLISH
RFX9400 Starter's Guide...
User manual - Page 6
... IR Emitters 2 Mini-jack IR Cables
Crossed Ethernet cable
3 RFX9400 Starter's Guide
Unpacking the Extender
Pronto Wireless Extender Antenna
Front Panel
Power LED WiFi LED Ethernet LED Busy LED
Back Panel Power input
4 dipswitches for the IR outputs
Stand-alone/ Network switch
4 IR outputs
Ethernet input (RJ45)
Extender ID switch
Configuration switch • In Stand-alone Mode:
changes...
User manual - Page 7
...; Make sure the same Extender ID and RF channel are used on the Extender and the Pronto Control Panel.
3 Configure the Control Panel's configuration file so that the Control Panel can work with ID 0, set the Extender ID switch to an ID that is not used yet.
• If there is made part of the wireless Pronto Network. Stand-alone Connection
To configure...
User manual - Page 8
... IP address: the IP address, netmask and default gateway. The Configuration Tool opens in the browser.
6 Follow the onscreen instructions and make sure you do not need to connect any more cables.
9 Set the switches correctly:
Stand-alone/Network Configuration switch Extender ID
Network 1 0
The Extender will restart. The Extender will be connected wirelessly to the Pronto Network: the...
User manual - Page 9
RFX9400 Starter's Guide
Configuring the Extender through a Router
When the Extender is already installed and connected to external AV-equipment, it is possible to configure it through a router.
1 Connect the Extender... in the Pronto Network.
5 Select the Extender that the antenna is placed correctly. Extender
Straight Ethernet cable
Router
ENGLISH
2 Set the Extender's Configuration switch...
User manual - Page 10
.... 7 Refer to the topic 'The IP address cannot be determined • When using the same fixed IP address as the Extender. If the problem persists, check the router settings.
Insert the other mini-jack connector in the network that is using the Extender: make sure that the Extender is being configured.
WiFi LED The Extender's IP address is connected to an...
User manual - Page 11
... red blinking • Check the router's network settings and make sure the PC is not using a fixed IP address but is using DHCP, the Extender's IP address cannot be determined. The Extender cannot communicate with the Control Panel.
There are set correctly. • Make sure that you send a command with the wireless network
The WiFi LED is red • Make sure...
User manual - Page 12
... being operated by a different Control Panel.
Stand-alone/Network Configuration switch Extender ID
Network 2 0
3 Open the browser.
4 Type the IP address of the Extender (printed on the Philips Pronto website: www.pronto.philips.com. The Firmware Update page opens.
6 Follow the onscreen instructions.
Updating the Extender through a router.
1 Connect the Extender to the router, and the...
User manual - Page 13
...this Starter's Guide may be subject to 16 extenders and 16 control panels in a system (for technical or editorial errors in the Pronto Network.
5 Select the Extender that you want to change without notice.
Specifications
The specifications and design of this manual or for Power, WiFi, Network and Busy Up to change without prior notice. ENGLISH
RFX9400 Starter's Guide
3 Open...
User manual - Page 34
...accordance with the instructions, may cause...
IFU Approbation / Safety Content RFX9400
FCC Compliancy
This device complies with Part 15 of the FCC rule....003. If the equipment does cause harmful interference to radio or television reception, which can radiate radio frequency energy and, if not installed and used in residential installations. This equipment has been tested and found to part...
User manual - Page 39
Notas - Notes
Concept and Realization of this Starter's Guide: Concepto y elaboración de este Manual de inicio: Documentation et élaboration de ce Guide de démarrage:
The Human Interface Group, De Regenboog 11, 2800 Mechelen (Belgium) http://www.higroup.com
3104 205 3426.1 Notes -
Philips RFX9400 Reviews
We have not received any reviews for Philips yet.