Pyle PINV1 Support and Manuals
Popular Pyle PINV1 Manual Pages
PINV1 Manual 1 - Page 2
...personnel injury, property damage, and or loss of life.
-WARNING
• Shock Hazard. The PINV1/PINV2/PINV3 will be connected only to batteries with inductive
loads, such as its housing may become...PINV2 / PINV3 is designed for indoor use only and not recommended for purchasing the PYLE View DC to AC Power Inverter. Keep away from a 12 Volt battery to serve such as normal household wall
...
PINV1 Manual 1 - Page 3
AC OUTLET 2. POWER ON LED 4. BINDING POST TERMINAL
2 FEATURES
PINV1
1. ON/OFF SWITCH 3. AC OUTLET 2. PROTECTION LED 5. PROTECTION LED 5. ON/OFF SWITCH 3. LIGHTER PLUG
PINV2 / PINV3
1. POWER ON LED 4.
PINV1 Manual 1 - Page 4
...Watts. the PINV1 is not suitable for operating at 150 Watts, the power source must be a battery or a well-regulated 12V/30A DC power supply. CAUTION : DO NOT USE THIS INVERTER WITH THE ... FLASHLIGHTS, SOME RECHARGEABLE
SHAVERS and NIGHT LIGHTS that are over than 150 Watts, connect the inverter directly to 150 Watts. D. Then connect the BLACK battery chip to the NEGATIVE (-) terminal...
PINV1 Manual 1 - Page 5
... : A. When operated from a vehicle cigarette lighter (PINV1/PINV2/PINV3) A consumption of inverter and replace the blown fuse with a new spade type fuse, 20A for PINV1, 35A for PINV2 and 30A X 2 for PINV2 / PINV3. Determine the cause of 150 Watts or less for PINV3. It also acts as a manual reset for connection directly to standard electrical...
PINV1 Manual 1 - Page 6
...before its capacity and the power level drawn by the particular AC load. Operating the inverter from a vehicle battery until the low voltage alarm sounds will vary depending on the desired... times. The vehicle batteries are not intended for engine starting may trigger the inverter's low voltage shutdown feature. The inverter can be expected with a 100 to provide brief periods of 1 hour or...
PINV1 Manual 1 - Page 7
....
Replace fuse. The fuse of cigarette lighter or 12 Volt outlet is blown The fuse of inverter is connected to a power source with reverse DC input polarity. Check to cool for 15 minutes. Use the product not exceeds the inverter's surge capacity, 300 Watts (PINV1) , 600 Watts (PINV2) and 800 Watts (PINV3) . The inverter needs repairment...
PINV1 Manual 1 - Page 8
... Recharge battery Check condition of battery clips and terminals. SYMPTOM C: THE LOW OUTPUT OF INVERTER IS MEASURED
POSSIBLE CAUSES Battery voltage is too low below 10V DC The inverter is overload
SUGGESTION Recharge battery Reduce load to 150 Watts (PINV1) , 300 Watts (PINV2) and 400 Watts (PINV3) maximum to maintain regulation.
Clean or...
PINV1 Manual 1 - Page 9
... point (nominal 15 Volts Number of ac receptacles 1 (PINV1)/2(PINV2)/2(PINV3) Weight...0.62 kgs/1.37 lbs. (PINV1) ...1.02 kgs/2.25 lbs. (PINV2) ...1.30 kgs/2.86 lbs. (PINV3) Dimensions (W x H x D mm 121x53x118 (PINV1) ...121x53x170 (PINV2) ...121x53x214 (PINV3)
Specifications are subject to change and improvement without notice.
8 Specifications are typical; individual units might vary.
Pyle PINV1 Reviews
Do you have an experience with the Pyle PINV1 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Pyle yet.
Earn 750 points for your review!