Ridgid JP0610 Support and Manuals
Get Help and Manuals for this Ridgid item
View All Support Options Below
Free Ridgid JP0610 manuals!
Problems with Ridgid JP0610?
Ask a Question
Free Ridgid JP0610 manuals!
Problems with Ridgid JP0610?
Ask a Question
Popular Ridgid JP0610 Manual Pages
Owners Manual - Page 1
.... Thank you for , it will give you years of rugged, trouble-free performance.
When properly cared for buying a RIDGID product.
JOINTER/PLANER
JP06101
�
Your Jointer/Planer has been engineered and manufactured to RIDGID's high standard for dependability, ease of injury, the user must read and understand the operator's manual before using this product. OPERATOR'S MANUAL
6-1/8 in.
Owners Manual - Page 3
Read the operator's manual carefully.
Cluttered work areas and work into moving parts, breakage of at all tools should wear safety glasses and be properly repaired or replaced by the cord or yank it will do the job better and safer at an authorized service facility. n DO NOT USE IN DANGEROUS ENVIRONMENTS.
n USE THE RIGHT TOOL.
Use only a cord...
Owners Manual - Page 4
... connecting to clean tool.
n WHEN SERVICING use a clean cloth when cleaning.
Do not rush.
n DOUBLE CHECK ALL SETUPS. n STAY ALERT AND EXERCISE CONTROL. n DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. n INSPECT FOR AND REMOVE ALL NAILS FROM LUMBER BEFORE USING THIS TOOL. Always use only identical replacement parts. n NEVER START A TOOL WHEN...
Owners Manual - Page 7
... operation and instructing others who may result in property damage.
We recommend Wide Vision Safety Mask for use only identical replacement parts. SYMBOLS
The following signal words and meanings are intended to explain the levels of any power tool can result in foreign objects being thrown into your nearest AUTHORIZED SERVICE CENTER for repair. SYMBOL
SIGNAL...
Owners Manual - Page 10
... part ...Set...used to help keep the kerf open and also helps to make thinner pieces.
Leading End The end of the end) is not properly supported...used for jointer planers) Device used...guiding it applies to the table surface.
GLOSSARY OF TERMS
Anti-Kickback Pawls (radial arm and table saws) A devise which, when properly installed and maintained, is being done.
Featherboard A device used...
Owners Manual - Page 12
.... Also tool storage for making adjustments or installing the knives:
PHILLIPS SCREWDRIVER STRAIGHT EDGE
ADJUSTABLE WRENCH OPEN END WRENCH (1/2 IN.)
COMBINATION SQUARE
Fig. 7
12
TOOLS NEEDED
FENCE TILT HANDLE
Assists in .
It must always be removed from the table.
ANGLE GAUGE
Used to set the fence at a desired height. When the key is not connected...
Owners Manual - Page 17
... Install switch key into place as shown. WARNING:
This tool is right side up the holes in .
n Locate the following : Serrated Hex Head Bolts (3), 3/8-16 x 3/4 in jointer table ... when needed. n Place the cabinet on left side.
n Line up .
n Using 3/16 in . n Bolt the jointer table to the cabinet using hex head bolts and tighten all the bolts. ASSEMBLING SWITCH
See Figure 17. screws,...
Owners Manual - Page 18
...With assistance, set the jointer upright. To avoid back injury, lift with nuts and bolts.
V-BELT
PAN HEAD SCREW
18
REAR PANEL
CABINET Fig. 18
SLOTS
1...the inside of the pulleys and adjust the motor as jointer table mounting bolts at this time.
n Position the rear ... when needed . ASSEMBLY
ASSEMBLING REAR PANEL
See Figure 18. Bolt in place using 3/16 in on the V-belt. n Reinstall the...
Owners Manual - Page 21
... n Twisting the wood while making a cut to edge. n Always support long workpieces.
n Always use clean, sharp, and properly-set
knives. n Adjust the depth of a second is sufficient to a full and complete stop. Wait until the jointer/planer has come to inflict severe injury.
n Unplug the jointer/planer from the switch assembly. Remember that a careless fraction...
Owners Manual - Page 30
... of the cut . n Finger tighten each of the jointer. n Check that the table raises and lowers freely with the knives of the cutter head at the correct height, lock in .; n After the outfeed table has been set screws and repeat adjustment. n As a final check of the outfeed table adjustment, run a piece of wood slowly over
the...
Owners Manual - Page 31
... in service. The table extension is complete, reinstall the pan head screw in 1/2 turn increments by turning tension knob clockwise. In the event that attach the extension to set the fence to the cutter head guard in the bottom of cutter guard travel. n Using a straight edge, align the extension to be flush with the RIDGID jointer...
Owners Manual - Page 32
...Troubleshooting Chart." Disassembly of motor damage, this may be damaged by an Authorized Service Center. Disregarding this motor should be done by their use only identical RIDGID replacement parts...for your model and a...types of the jointer/planer.
If...troubles may create a hazard or cause product damage. Use clean cloths to clean the tool using solvents when cleaning plastic parts...
Owners Manual - Page 34
...on planed surface Kickbacks
1.
Do not use any attachments or accessories not recommended by a qualified service technician. The use with this tool are set higher than other
2.
TROUBLESHOOTING
Problem
Cause
Solution
Motor will not run
1. Defective On-Off switch Defective capacitor Defective motor
2. Belt tension too high
1. Repair service is done by the manufacturer of...
Owners Manual - Page 35
..., appliances and other motors
1.
Frequent opening of which the motor is loose
1. Do not use other appliances or motors on same circuit when using the jointer. Tighten set screw is capable, and a reduction of 20% in blown fuses or tripped circuit breakers.)
1. Have start capacitor
1. TROUBLESHOOTING
Problem
Cause
Solution
Excessive noise
1. Motor 2.
Owners Manual - Page 40
...'S MANUAL
6-1/8 in the space provided below. For the location of this tool is found on a plate attached to provide all relevant information when you , please call or visit.
JP06101
Serial No.
983000-393 9-04 JOINTER/PLANER
JP06101
Customer Service Information:
For parts or service, contact your nearest RIDGID authorized service center. The model number of the authorized service...
Ridgid JP0610 Reviews
We have not received any reviews for Ridgid yet.