Ryobi BS904 Support and Manuals
Get Help and Manuals for this Ryobi item
Most Recent Ryobi BS904 Questions
Drive Belt Comes Off Motor Pulley
This happens even after adjusting the motor for different tension levels. It will run maybe 20/30 se...
This happens even after adjusting the motor for different tension levels. It will run maybe 20/30 se...
(Posted by jboyd17770 7 years ago)
Ryobi Bs904 Fence?
Does ryobi make an adjustable fence for the BS904? I cant seem to find anything.
Does ryobi make an adjustable fence for the BS904? I cant seem to find anything.
(Posted by ctwistedpair 10 years ago)
Ryobi BS904 Videos
Ryobi BS904 9 Inch Bench Top Band Saw Cutting Aluminum
Duration: 3:23
Total Views: 2,569
Duration: 3:23
Total Views: 2,569
Popular Ryobi BS904 Manual Pages
Operation Manual - Page 3
....
REMOVE ADJUSTING KEYS AND WRENCHES. If repair or replacement of the tool, a guard or other flammable liquids, in use of the blade or cutter only.
NEVER LEAVE TOOL RUNNING UNATTENDED. Failure to follow all tools should be disconnected from tool before servicing, or when changing attachments, blades, bits, cutters, etc., all instructions listed below, may...
Operation Manual - Page 4
... are doing and use .
BEFORE CHANGING THE SETUP, REMOVING COVERS, GUARDS OR BLADES, unplug the saw and remove the switch key.
HOLD THE WORKPIECE firmly against the blade.
USE ONLY CORRECT BLADES. All repairs, whether electrical or mechanical, should point down toward the table.
ALWAYS SUPPORT LARGE WORKPIECES while cutting to minimize risk of cut...
Operation Manual - Page 8
... SAW BLADE
Saw comes with tilt control. SAW TABLE WITH THROAT PLATE
Your band saw has a saw table for a crosscut. RAPIDSET™ BLADE TENSION LEVER
Controls blade tension when changing blades and making adjustments. blade. Tightening the table lock lever locks the saw . FEATURES
PRODUCT SPECIFICATIONS
Blade Width 1/8 in place. The throat plate, installed in this operator's manual...
Operation Manual - Page 9
... to a firm supporting surface such as a pattern, locate and mark the holes where the band saw is to be used , make sure that can occur during shipping. CLAMPING BAND SAW TO WORKBENCH
See Figure 5, page 18.
NOTE: This saw base, lock washers, hex nuts, and the thickness of saw on until blade tension has been properly set.
Do...
Operation Manual - Page 10
... or down to align table 90° to blade (0° position). ADJUSTING BLADE TENSION
See Figures 10 - 11, pages 19 - 20.
Remove the switch key.
Before using the band saw, turn the upper wheel clockwise.
Too much tension may cause the blade to engage tension.
Check that blade guides do not interfer with your left hand while...
Operation Manual - Page 11
... the blade. If you careless. Turn the saw off, remove the switch key, and unplug the saw run. Do not restart until locating and correcting the problem. CUTTING PROCEDURES
Hold the workpiece firmly against the saw . allow familiarity with ANSI Z87.1. A 1/4 in . wide blade will cut is basically a "curve cutting" machine that you check and adjust blade guide settings before...
Operation Manual - Page 14
... screws and push thrust bearings to the back of a dollar bill) by hand, a full three rotations to contact the blade and release. Tighten set
screws using hex keys. Slide the upper blade guide support on the band saw blade during cutting.
above the workpiece.
Turn the lock knob counterclockwise to allow 1/64 in place. The adjustment of...
Operation Manual - Page 15
... type wax to comply with plastic parts. MOTOR/ELECTRICAL
Frequently vacuum or blow out sawdust from the power supply and the switch is unplugged from the motor. Replacing tires: Open front cover and remove saw blade and close the front cover. See section on
Installing and Adjusting the Blade, page 13. Pry the worn...
Operation Manual - Page 16
...English TROUBLESHOOTING
PROBLEM
CAUSE
SOLUTION
Motor will not cut straight.
1.
Blade is noisy when running.
1. Dull blade.
1.
Adjust upper and lower blade guides and bearings. Motor defective.
2. Have
tool repaired by a qualified
service technician.
Band Saw slows down when
1. Problem with the blade. Have worn parts replaced before using band saw...
Repair Sheet - Page 1
BS904 Repair Sheet RYOBI 9 in. Band Saw Model No.
Repair Sheet - Page 3
... 089120406083
DESCRIPTION
QTY. MODEL NUMBER BS904
The model number will be performed by a Ryobi Authorized Service Center. Hd 2 ...ID6.3 x OD16 x 1.5t 1 Slide Plate 1 Square Nut 1 Upper Blade Guide Assembly 1 Gear 1 Set Screw (M4 x 4 mm 1 Handle Seat 1
WARNING: Improper repair of your BAND SAW or when ordering repair parts. Key No. 87 1 Screw (M5 x 10 mm 1 Washer (ID5.3 ...
Repair Sheet - Page 4
... 1 Operator's Manual
WARNING: Improper repair of your BAND SAW or when ordering repair parts.
For the service center nearest you call 1-800-525-2579.
4 x 6 mm x 0.3t 1
Miter Gauge Assembly 1
Hex Wrench (M2 1
Hex Wrench (M4 1
Switch Key 1
Screw (M4 x 10 mm 8
Washer (ID6 x OD12 x 0.5t 1
Guide Height Knob Assembly (Inc. BAND SAW - Hd 4
Square Cover 1
Set Screw (M5...
Repair Sheet - Page 6
... repair of your BAND SAW or when ordering repair parts. PARTS LIST FOR FIGURE B
KEY PART NO. BAND SAW - Any repairs requiring disassembly of a double insulated tool can result in damage to the motor housing. For the service center nearest you call 1-800-525-2579.
6
Always mention the model number in . MODEL NUMBER BS904
The model number will be performed by a Ryobi Authorized Service...
Repair Sheet - Page 8
... Blade Wheel (Lower 1 10 089120406098 Spring Washer (M5 3 11 089120406097 Screw (M5 x 16 mm 3
WARNING: Improper repair of your BAND SAW or when ordering repair parts. RYOBI 9 in damage to the motor housing.
PARTS LIST FOR FIGURE C
KEY PART NO. For the service center nearest you call 1-800-525-2579.
8 BAND SAW - MODEL NUMBER BS904
The model number will be performed by a Ryobi...
Repair Sheet - Page 10
...shock or electrocution. MODEL NUMBER BS904
The model number will be performed by a Ryobi Authorized Service Center. Hd 2 12 089120406044 Screw (M5 × 16 mm, Hex Soc. Hd 1 16 089120406057 Guide Block (Lower 1 17 089120406053 Guide Block (Lower 1 18 089120406050 Thrust Bearing Shaft (Lower 1
WARNING: Improper repair of your BAND SAW or when ordering repair parts. Any repairs requiring...
Ryobi BS904 Reviews
We have not received any reviews for Ryobi yet.