SanDisk SDCFS-128-A10 - Compactflash Card 128MB Support and Manuals
Get Help and Manuals for this SanDisk item
This item is in your list!
View All Support Options Below
Free SanDisk SDCFS-128-A10 manuals!
Problems with SanDisk SDCFS-128-A10?
Ask a Question
Free SanDisk SDCFS-128-A10 manuals!
Problems with SanDisk SDCFS-128-A10?
Ask a Question
Popular SanDisk SDCFS-128-A10 Manual Pages
Product Manual - Page 28
Interface Description
SanDisk CompactFlash Card OEM Product Manual
3.3.3
Power Up/Power Down Timing
The timing specification in Table 3-9 was defined to permit peripheral cards to perform powerup initialization. Table 3-9 Power Up/Power Down Timing
Item
Value
CE Signal Levela
CE Setup Time CE Setup Time CE Recover Time VCC Rising Timeb VCC Falling Timeb Reset Width...
Product Manual - Page 29
.... 100
-----------
5
5
0
10
Max. --100 100 50 50 50 ---------
© 2007 SanDisk Corporation
3-11
Rev. 12.0, 02/07 SanDisk CompactFlash Card OEM Product Manual
Interface Description
Figure 3-2 Power Up/Power Down Timing for all types of memory. Table 3-10 Common Memory Read Timing Specification
Speed Version Item Read Cycle Time Address Access Timea Card Enable...
Product Manual - Page 35
SanDisk CompactFlash Card OEM Product Manual
Interface Description
Table 3-14 contains the specification information related to the minimum cycle time defined by the associated mode (e.g., a device supporting PIO Mode 4 timing will not report a value less than or equal to the I /O Write Timing Specification
Item Data Setup before -IOWR Data Hold following -IOWR -IOWR Width Time Address Setup...
Product Manual - Page 36
... negation edge of signals -CS0, -CS1 and -DA(2:0). Interface Description
SanDisk CompactFlash Card OEM Product Manual
Figure 3-7 Register Transfer to/from Device
PIO Timing Parameters
t0 a
Cycle...sum of DD(7:0). b. A device imple mentation shall support any legal host implementation. recovery time (min.)
t3
IOWR- setup (min.)
t2 a
IORD-/IOWR- Data consists of t2 ...
Product Manual - Page 38
...
SanDisk CompactFlash Card OEM Product Manual
The PIO data transfer parameters are located in the system.
02/07, Rev. 12.0
3-20
© 2007 SanDisk Corporation data setup ...support any legal host implementation. t0 is the minimum total cycle time, t2 is the minimum command active time, and t2i is no longer driven by appropriate information in the Card Information Structure (CIS).
setup...
Product Manual - Page 47
... and Even Data Bus (D15-D0).
This 1 KByte memory window to the data register is accessed with -CE1 low and -CE2 high. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.3
Memory Mapped Addressing
When CompactFlash Memory Card registers are accessed via memory references, they appear in the common memory space...
Product Manual - Page 49
... 0 with CE2 low and -CE1 high. This register is "0" at command completion. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
Table 4-6 Data Register
Data Register Error/Feature Register Error/Feature Register
CE2- D5
0
Bit set to 0. D3
0
Bit set to complete the request.
4.5.5
Sector Number (LBA 7-0) Register (Address-1F3[173]; If the value...
Product Manual - Page 51
... command buffer and
registers and the host is set , indicates a write fault has occurred. D0
ERR
Set when the previous command has ended in the Error Register contain additional information describing the error.
4.5.10 Device Control Register (Address-3F6[376]; SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.5.9
Status & Alternate Status Registers (Address...
Product Manual - Page 59
... command Double-word not supported Capabilities: DMA Supported (bit 8), LBA supported (bit 9) Reserved
© 2007 SanDisk Corporation
5-5
Rev. 12...Firmware revision in ASCII (Rev M.ms) set by code Big Endian Byte Order in Word Model number in ASCII (left justified) Big Endian Byte Order in Word Maximum No. All reserved bits or words are "0". SanDisk CompactFlash Card OEM Product Manual...
Product Manual - Page 64
... not be interpreted by host implementers.
Obsolete
12
1
Write Buffer command supported by CF Card
13
1
Read Buffer command supported by CF Card
14
1
NOP command supported by CF Card
Words 85-87: Features/Command Sets Enabled.
ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
Word 68: Minimum PIO Transfer Cycle Time With Flow Control.
Product Manual - Page 65
...
Bit
Setting
Indication
0
0
SMART feature set not enabled
1
1
Security Mode feature set enabled via the Security Set Password command
2
0
Removable Media feature set not supported
3
1
Power Management feature set supported
4
0
Packet Command feature set not enabled
5
1
Write cache enabled
6
1
Look-ahead enabled
7
0
Release Interrupt not enabled
8
0
Service Interrupt...
Product Manual - Page 70
... every sector, but DRQ is the same as possible are posted at the sector where the error occurred.
If the number of requested sectors is programmed by a Set Multiple, command. ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.11
Read Multiple-C4H
The Read Multiple command performs similarly to the Read Multiple command...
Product Manual - Page 73
... command is effectively a NOP command to the card although it does perform a range check of range. SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Table 5-24 defines the valid extended error codes for the CompactFlash Memory Card Series product. The extended error code is out of cylinder and head or LBA address and returns an...
Product Manual - Page 74
...Specification.
The 9AH feature is unique to CompactFlash Memory cards and are used by the host to enable and clear 8-bit data transfer mode. Features 01H and 81H are not part...Count register.
ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.18 Set Features-EFH
This command is issued, all features that are supported.
Table 5-26 Set Features
Bit
7
6
5
4...
Product Manual - Page 106
... published specifications as new products. or improper alterations or repairs.
RECEIVING WARRANTY SERVICE
According to SanDisk's warranty...
SanDisk CompactFlash Card OEM Product Manual
All failing products returned to SanDisk under...specifications.
If approved, SanDisk will be returned. V. This warranty does not cover defects, malfunctions, performance failures or damages to repair or replace...
SanDisk SDCFS-128-A10 Reviews
Do you have an experience with the SanDisk SDCFS-128-A10 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for SanDisk yet.
Earn 750 points for your review!