Singer 14J250 STYLIST II Support and Manuals
Get Help and Manuals for this Singer item
View All Support Options Below
Free Singer 14J250 STYLIST II manuals!
Problems with Singer 14J250 STYLIST II?
Ask a Question
Free Singer 14J250 STYLIST II manuals!
Problems with Singer 14J250 STYLIST II?
Ask a Question
Singer 14J250 STYLIST II Videos
Singer 14J250 Stylist II. Right out of the box-Demo 1
Duration: 21:14
Total Views: 6,979
Duration: 21:14
Total Views: 6,979
Singer 14J250 Stylist II Serger - Threading Guide Right Needle - InternetSalesUSA.com
Duration: :35
Total Views: 996
Duration: :35
Total Views: 996
Singer 14J250 Stylist II. Out of the box demo # 2
Duration: 31:29
Total Views: 2,533
Duration: 31:29
Total Views: 2,533
Popular Singer 14J250 STYLIST II Manual Pages
Instruction Manual - Page 2
... only)
Use Model YC-482E with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they do not play with a damaged needle plate as threading needle, changing
needle, threading looper, or changing presser foot, etc." 18. Close attention is necessary when this sewing machine." Return the sewing machine to install the proper outlet...
Instruction Manual - Page 11
... power cord plug to the right and down towards you with your right hand. SETTING UP YOUR MACHINE
1. POWER/ LIGHT SWITCH Your machine will not operate unless the power/light switch is turned on. When leaving the machine unattended or servicing the machine, remove the power cord plug from the power supply outlet.
4. OPENING FRONT COVER...
Instruction Manual - Page 19
...
Tissus légers: Crêpe, voile, satin
Tissus ...thread, for example, is an unusual color, you should buy sufficient thread for ordinary overlocking. When purchasing thread for sewing, especially if it is very useful for different types of thread...threads are recommended for your project.
18
TABLEAU DES FILS ET MATIERES
Utiliser SINGER Cat. NEEDLE, THREAD AND FABRIC CHART
Use...
Instruction Manual - Page 27
...thread.
6. Lower the presser foot. Set the needle threader ensuring the hooking fork enters into hooking fork and pull the thread with the needle threader in one hand.
4. Hold the thread...izquierda
26
7 7 Guide the thread into the needle hole.
3. Feed the thread through the thread guide of the machine. Move the needle threader backwards slightly. Pull the thread toward the back of...
Instruction Manual - Page 33
... correctly placed in many cases. Try test-sewing with a piece of threads
4
Overedge cutting width dial
← 6 →
6
Needle to use and find the best settings.
* When threading upper looper with wooly nylon thread, set the thread tension control dial at ← 2 →. Incorrect tension setting causes stitch skipping.
Reduce the tension when you use
Left and...
Instruction Manual - Page 37
THREE-THREAD OVERLOCK WITH ONE NEEDLE
By threading the LEFT needle only, a seam allowance width of 0.15 inches (3.8mm) will be produced. Pull out the two-thread converter as illustrated in Fig... in the needle pad as shown in the needle pad. Illustration * I : Two-thread converter * II : Upper looper
36 By threading the RIGHT needle only, a seam allowance width of 0.24 inches (6 mm) will...
Instruction Manual - Page 39
... threads below for needle
Upper looper
Lower looper
Narrow overlock edge
with Three Threads
...II : Cross section showing proper placement of stitch finger * III : Narrow hem * IV : Rolled hem * V : Picot stitch
38 RECOMMENDED THREAD
Thread for ideal seams.
2. Raise the presser foot.
2. When finished, replace...Set the machine according to the Setting Chart on fine scarf-like fabrics.
Instruction Manual - Page 45
...may hang off the edge when you sew with lightweight fabric using three threads (right needle only) and setting the width dial at 4 - 5 (Fig. 3). ADJUSTING STITCH LENGTH... turning the Overedge cutting width dial to get proper stitching. (Fig. 4)
Illustration
* I : Stitch length dial * II : Overedge cutting width dial * III : Stitch finger (B) * IV : Cross section view of stitch finger
Fig. ...
Instruction Manual - Page 47
...feed *III : Negative differential feed
46
* I
(B)
* II
(B)
* III
(A) (A) (A)
POSITIVE DIFFERENTIAL FEED
WHEN SET FOR POSITIVE DIFFERENTIAL FEED, the front feed dog (A) makes ...effect of accumulating fabric under the presser foot to feed at different ratios.
NEGATIVE DIFFERENTIAL FEED
WHEN SET FOR NEGATIVE DIFFERENTIAL FEED, the front feed dog (A) makes a shorter stroke than the rear feed...
Instruction Manual - Page 49
... * I : Differential feed control dial * II : Increase *III : Decrease *IV : Tighten * V : Loosen *VI : Cutter release mechanism screw.
48 If adjustment is set at the factory, so you tighten the screw...multiple layers of feeding.
For normal sewing without differential feed, set at the factory for your fabric. The machine is necessary, turn the overedge cutting width dial to adjust ...
Instruction Manual - Page 57
...heads, sleeve bottoms and ruffles, etc. Set the differential feed control dial between 1.5 and 2, tighten the left and right needle thread tensions and/or lengthen or shorten the ...seams, set the differential feed control dial at less than 1.
3. It is also very effective for your fabric. Illustration
* I : Even, smooth seam * II : Puckering * III : Wavering * IV: Gathering
56
* I * II * ...
Instruction Manual - Page 59
CARING FOR YOUR MACHINE
REPLACING THE CUTTER
Replace the Moving cutter if it with the screw.
FIRST ...2. 3. Open the working table and disengage the Moving cutter by turning the cutter release knob toward you . In this position, set the replacement cutter in your accessories.
* I : Screw * II : Stitch finger * III : Moving cutter * IV : Cutter release knob * V : Face cover * VI : Face ...
Instruction Manual - Page 61
...: U se dry rags to remove dust and lint.
Cleaning the serger and foot control
Keep the serger and foot control clean. Illustration
* I : Top cover screw * II : Top cover * III : Brush * IV: Oil
60 Open the front cover and working table.
FIRST DISCONNECT THE MACHINE FROM THE POWER SUPPLY BY REMOVING THE POWER CORD PLUG...
Instruction Manual - Page 63
... guide it gently Insert correct size needle for thread and fabric Reset Needle Re-attach presser foot
Reset thread tension (s) Re-insert or replace needle Set it at less than 1
Set it gently Re-attach presser foot
Do not pull fabric; Re-thread machine Insert correct size needle for knitted fabrics.
REMEDES A D'EVENTUELS PROBLEMES
PROBLEM
Irregular Stitches
PROBABLE CAUSE
Incorrect thread...
Instruction Manual - Page 65
... ribbon can be used in straight seams.
Use for a 3-thread flat lock, left needle only. Replace with 2" of collars, cuffs, pockets, etc. 5.
Close ... secure the pearls. • Follow edge of fabric along fabric guide on Pearl foot. • Sew pearls on the right side ...with the left needle (remove right needle) 3-thread overlock. Set tensions as for left needle just catching the fold...
Singer 14J250 STYLIST II Reviews
We have not received any reviews for Singer yet.