Sony XVS-7000 Support and Manuals
Get Help and Manuals for this Sony item
View All Support Options Below
Free Sony XVS-7000 manuals!
Problems with Sony XVS-7000?
Ask a Question
Free Sony XVS-7000 manuals!
Problems with Sony XVS-7000?
Ask a Question
Popular Sony XVS-7000 Manual Pages
Users Guide - Page 15
...
AUX Bus Remote Panel 533 Procedure for Simple Connection 533 Setting Status of the MKS-8080/8082 in
Simple Connection 534 ...Setup Define 548 Data Saved by [Init Status Define 549 Error Messages 552 Error Messages Displayed in the Error
Status/Error Log Menu 552 Error Messages Appearing in a Message
Box 553 Error Messages Shown in the Error
Information Menu 558 Maintenance 559
Replacing...
Users Guide - Page 16
...-8475 DME Board
XKS-8470 HD DME Board
Terms used in this manual
• XVS-9000 • Switcher • Multi format switcher
• XVS-8000 • Switcher • Multi format switcher
• XVS-7000 • Switcher • Multi format switcher
• XVS-6000 • Switcher • Multi format switcher
• ICP-X7000 • Control panel • Integrated control panel
•...
Users Guide - Page 60
..., and then press a VF button or parameter setting button to return the parameter values or function enable/disable settings to their default values, in the Setup menu.
And you can position the mouse cursor...a Mouse
You can also switch the functions of the control panel setup. You can register 15 buttons in the same way as part of the right and left -click and enter a value in ...
Users Guide - Page 67
...: XKS-T8165, QSFP+ type: XKS-Q8166, QSFP28 type: XKS-C8166)
Used as output connectors to connect to two output systems are supported. The output setting is detected, due to the XVS-9000/8000/ 7000/6000 Installation Manual. p MVS LAN (multi format video switcher LAN) connector (RJ-45 compliant)
Connect to an Ethernet switch. 1) Used to communicate between...
Users Guide - Page 123
...for which the key is selected on .
No.
Note
The PROC V and PROC K signals on each switcher bank cannot be configured. Key blink: The key is on key 1 of the selected key fill signal....the key fill and key source signals with DME effect applied are assigned. Key Blink: Sets key blinking. When [Key Blink] is replaced by the key fill and key edge fill state.
1 Open the M/E-1 >Key1 >...
Users Guide - Page 259
... expansion, the slant angle of the effect region, and trail direction, the degree to melt
1 Press [Form].
2 Set the following parameters. Down: Melting occurs downward.
2 To make wave settings for the melting part, press
[Border] and set
the following parameters. No. No. Parameter Adjustment
1
Amp
Amplitude of wave
2
Freq
Frequency of wave
3
Offset a) Wave...
Users Guide - Page 387
... to use.
1 In the Engineering Setup >System >Network Config
menu (7311), press [NFS Server].
2 Enter the server address using the keyboard window,
then press [Enter].
387 Unit ID settings
When there are two switchers on the switcher system LAN.
For details about unit IDs of 2nd switcher (Ch1 to the installation manual for the whole system. DME...
Users Guide - Page 390
... one of the Engineering
Setup >System >Network Config menu (7311), press [IP Address].
RS-FEC: Use Reed-Solomon FEC (CL108). 1) FC-FEC: Use Fire-Code FEC (CL74).
The IP Address menu (7311.2) appears.
2 In the group, select the target switcher to step 8. The status area shows the slot number, network settings status, and the...
Users Guide - Page 397
... each device after powering on (excludes Setup mode settings). User: Start up using the user data previously saved with
[Setup Define]. There are two modes available for the switcher and control panel.
You can set Setup mode and Initial Status mode settings separately. • Setup mode: Set one of the following setup states to set to 16:9 or 4:3.
1 In the Engineering...
Users Guide - Page 403
....
2 In the group, select the group containing
the target menu to set as the primary device. Changing the lock password
1 In the Engineering Setup >System >Maintenance
>Setup Operation Lock menu (7317.1), press [Change Password].
2 Check the message, then press [Yes].
3 Follow the on-screen instructions to select all locked.
Initializing the Local Drive
"Local Drive" refers...
Users Guide - Page 404
... lock candidate menu selection is displayed as the candidate for locking.
Changing the lock password
1 In the Engineering Setup >System >Maintenance
>File Load Lock menu (7317.2), press [Change Password].
2 Check the message, then press [Yes].
3 Follow the on-screen instructions to white.
To deselect all locked. In this case, [Lock Item Select] is reflected...
Users Guide - Page 525
... in the switcher
DMEs
Screen aspect Transitions
Restrictions
• M/E-5 bank (XVS-9000/8000), M/E-3 to M/E-5 banks (XVS-7000), M/E-2 to M/E-5 banks (XVS-6000) a)
• Key 5 to key 8 (3840×2160P), key 3 to key 8 (3840×2160PsF)
• M/E Config multi-program 2 mode • Utility 1 and 2 buses • Side flags • M/E split
• In SQD, DMEs not supported • On...
Users Guide - Page 526
...
For the administrator user name and password, refer to the ICP-X7000 Installation Manual.
1 Access Resource Share Setup. Notes
• When the signal format is used, signals configured using the Engineering Setup >Switcher >Input >Dedicated Input Assign menu (7332.10) can also be used.
• You can set to DMEs not supported
a) When a dedicated input is 3840×...
Users Guide - Page 529
... multi viewer outputs and multi viewers.
• If the logical switchers are used on logical switchers 1 and 2. Select [1] or [2] for each group of 8 outputs.
Notes
• The resource settings setup pop-up window.
Select [1] or [2] for each group of four channels. Internal format converter settings (XVS-8000/ 7000/6000 only) Click/tap [Select] for [Internal FC (ch...
Users Guide - Page 563
...388 NFS 376, 387 setting 387
Network AUX remote panel 535 Network interface
Initialize 388 protocol 392 service port 388 setting 388 Network port external devices...setting 427, 478 supported devices 282 timeline 282 trigger 283 PGM/PST configuration 406 copying 185 dual M/E 406 inhibit operation 406 link 470 logical M/E 441 P/I converter 455 Post-macro 362 Power power-on state selection 397 switcher...
Sony XVS-7000 Reviews
We have not received any reviews for Sony yet.