TASCAM RC-898 Support and Manuals
Get Help and Manuals for this TASCAM item
View All Support Options Below
Free TASCAM RC-898 manuals!
Problems with TASCAM RC-898?
Ask a Question
Free TASCAM RC-898 manuals!
Problems with TASCAM RC-898?
Ask a Question
TASCAM RC-898 Videos
Tascam Da-38 and Rc-898 with Dm-3200 mixer
Duration: 3:40
Total Views: 227
Duration: 3:40
Total Views: 227
Popular TASCAM RC-898 Manual Pages
Owners Manual - Page 3
...
4.5 Storing and recalling user setups 4-4 4.5.1 Saving the current setup 4-4
4.5.2 Recalling a user setup or restoring factory
settings 4-5
5 -Basic DTRS operations
...manual 1-1
1.4 Precautions and recommendations........ 1-2 1.4.1 Environmental conditions 1-2 1.4.2 Battery backup 1-2 1.4.3 Digital audio cables 1-2 1.4.4 Reference clock in a digital studio 1-3
1.5 Accessories 1-3
2 -RC-898...
Owners Manual - Page 5
...
The box contains the following.
• RC-898 Remote Control Unit (x 1) • Accessories:
• Remote/sync connection cable (x 1)
• Remote/sync terminator (x 1)
• This manual (x 1)
• Warranty card (x 1)
1.3 About this manual
This manual is also a guide to the different menu screens available on the DTRS units": more advanced DTRS settings, that you to control up to...
Owners Manual - Page 6
... the manuals of the DTRS units and the SY-88. The number in the appropriate sections describing the front and rear panels. A special font is to be transported to the default settings. near the RC-898. If the unit is used : 00:23:45:12 or on the LCD display screen [11], for service or repair...
Owners Manual - Page 7
... sync").
Accessories
1-3 WARNING
Only use of specifications. Section 1.5 - Though the cables and connectors may be operated in the setup are used throughout a setup, it is more than TASCAM cables will be found convenient to mount the RC-898 on a roll-around stand, available as CS-898. The use TASCAM-supplied and TASCAM-approved cables when making such connections. It...
Owners Manual - Page 10
...set and view the input monitoring status of the tracks of a P2 recorder, as the keys on the RC-898 panel is used to control DA-88 and DA-38 units, the keys cannot be used to control the P2 unit in drop-frame format.The supported...color)
2-2 See section 7.1 of the DA-98 manual for this label, so the function is active. When the RC-898 is an abbreviation for individ- The DF indicator ...
Owners Manual - Page 11
...The ten number keys are set the different parameters available with the number keys, before storing a time to DTRS units. Off
The unit is also used to the RC-898. They indicate the timecode...in the chain.
code; The REL indicator, when lit, shows that the current time, relative to it has been wrongly entered.
2-3 The time reference is only supported by the currently-selected...
Owners Manual - Page 12
...VALUE display [15].
[29] CAPTURE key When this manual by the transport controls of the RC-898.
[32] CHASE key Pressing this key repeatedly will ....
[21] PRESET key This key is used to assign specific software menus to navigate through the menu tree to the preceding...indicator is unlit) and incrementing or decrementing the values being set in this is pressed, the current time is used to...
Owners Manual - Page 13
... your TASCAM dealer for automatic punch operations. NOTE
The two keys above , and to the equivalent table in the RC-898. Successive presses
of the DTRS units. Only use this key, see 6.7.1, "Setting punch ...on DTRS units. This will need to send GPI events from a small "cue list" in the manual of location points (a cue list) "on the LOCATE TIME/VALUE display [15].
It allows the ...
Owners Manual - Page 14
... visible from your system suffers from hum problems. However, a full discussion of ground loops and their associated problems is on the backlit LCD display screen ...set to use its own power for this manual, and we recommend that it off (up ) if your preferred viewing angle.
2-6 As shipped from the device to the tally supply pin, this switch is in the down ) position, allowing the RC-898...
Owners Manual - Page 15
...of the RC-898 to other than a DA-98 is more than TASCAM cables causes or results in the same setup. This ...RC898, allowing it is not possible to the units, the warranty is supplied by an RC-898 unit.
3.1.1 Machine IDs Set the machine IDs of the DTRS units so that the IDs run in the chain, they may not work correctly (see the DA-98 Owner's Manual, 10.5 and 13.2). WARNING
Use only TASCAM...
Owners Manual - Page 16
... specifications of a unit implementing the Sony P2 protocol.
This connection is lit.
3.4 A note on (down) to allow the RC-898 to the EXT 1 parallel port. It is
Unit
set (see the unit's manual
for...in a studio setup. Connections (parallel units)
the lowest ID. If this is not done, there is a risk that the control pins available match those provided by the RC-898 when the E2 ...
Owners Manual - Page 17
....
If you have noticed, the RC-898 requires no power supply of its own, drawing its power from the DTRS units to the default settings.
Memory and batteries
3-3 Section 3.5 - The battery should provide power for details of battery replacement.
3.5 Memory and batteries
As you see this message, contact your TASCAM dealer for several years of...
Owners Manual - Page 19
...will change to move between rows.
which may be edited is explained in the menu to which sets the amount of the varispeed as a percentage of this is highlighted by the menus").
4.1.1 ...an underline cursor. For the purposed of normal speed. The RC-898 sets parameters on the display screen to
In this operation on certain models of both fields are two editable fields, as a value ...
Owners Manual - Page 22
... can reload the factory settings, but the settings for the DTRS units connected to a function key:
1) Use cursor keys and the SELECT key until you see , there are the RC898's parameters stored and recalled...recall the "shifted" menu.
4.5 Storing and recalling user setups
The RC-898 allows you to store and recall almost all parameters set using the function keys
1) Simply press the function key ...
Owners Manual - Page 60
... of the DA-98 manual for example, the TASCAM ES-61 editing controller. Section 9.4 - These sources are ) as the RC-898. Track Mapping Mcn 1
Ana 1 2 3 4
Dig
1234
Trk 1 2 3 4 5 6 7 8
2) Use the UP and DOWN keys to select the track mapping, according to on, the REC FUNCTION keys which relate to cover every set options as shown...
TASCAM RC-898 Reviews
We have not received any reviews for TASCAM yet.