Bosch 1893-6 - 9 Large Angle Grinder Support and Manuals
Get Help and Manuals for this Bosch item
View All Support Options Below
Free Bosch 1893-6 manuals!
Problems with Bosch 1893-6?
Ask a Question
Free Bosch 1893-6 manuals!
Problems with Bosch 1893-6?
Ask a Question
Popular Bosch 1893-6 Manual Pages
Operating Instructions - Page 2
... safety
Stay alert, watch what you to your finger on the switch or plugging in
all instructions listed below refers to your body is an increased risk of dust extraction and collection facilities, ensure ...switch on . Use of these are likely to fail and create a hazard to a rotating part of flammable liquids, gases or dust. Damaged or entangled cords increase the risk of the power ...
Operating Instructions - Page 3
...When using only identical replacement parts. Grinding wheels or...grinder without the side handle could result in a hazardous situation.
Keep cutting tools sharp and clean. Service
Have your power tool serviced...parts. SAVE THESE INSTRUCTIONS
Angle Grinder Safety Rules
Always use . Accessories must have the power tool repaired before making any other practical way to secure and support...
Operating Instructions - Page 4
... silica from bricks and cement and other
reproductive harm. Wear proper apparel while using a grinder or installing a new wheel, inspect the grinding wheel for side loading and may cause electrical failures...., do this time. Your risk from these brushes and may entrap you or bystanders. Wheels intended for large angle sander/grinders are specially designed to the tool and positioned ...
Operating Instructions - Page 5
...
A
Direct current
0A
Alternating or direct current
Speed, torque or position settings.
This symbol designates that this tool is listed to NOM Mexican Standards.
-5- n0 .../min
No load speed
Rotational speed...Insulated Construction tools. This symbol designates that this tool is increasing from 0 setting Action in the direction of arrow Type or a characteristic of current Type or...
Operating Instructions - Page 6
... Dia. 5" Dia. 6" Dia. 6" Dia. 9" Dia.
* Always use appropriate size wheel guard.
-6-
Angle Grinders
SPINDLE LOCK
MOUNTING FLANGE
SPINDLE
PADDLE SWITCH VENTILATION OPENINGS
VIBRATION CONTROL
SIDE HANDLE
GUARD RELEASE / LOCK
LATCH
BUMPS
WHEEL GUARD
Model number No load speed Spindle thread Max.
BM 1609929H54 08-06 8/3/06 11:44 AM Page 6
Functional Description and Specifications
!
Operating Instructions - Page 7
...DISC GRINDING
WHEEL
LOCK NUT -7-
BM 1609929H54 08-06 8/3/06 11:44 AM Page 7
Grinder Assembly
WHEEL GUARD INSTALLATION
!
Always use the lock nut and backing flange that the two bumps on guard, line ... the guard's shell.
Do not
direct guard opening toward your body.
ADJUSTABLE CUP WHEEL GUARD INSTALLATION Open the guard clamp and fit it on the shell, and secure the shell for 1/4" ...
Operating Instructions - Page 8
... 28 OR TYPE 29
GRINDING WHEELS
!
The flanges
provided with your tool are not designed for proper wheel assembly when using the small flange set. SMALL FLANGE SET PART NO. 1 607 000 380
FIG. 1
FLANGE WITH SHOULDER
FLANGE OR LOCK NUT
FIG. 2
SPINDLE
FLANGE WITH SHOULDER
TYPE 28 GRINDING WHEEL
FLANGE OR LOCK...
Operating Instructions - Page 9
...grinder without the side
handle could cause loss of control of the
grinder...INSTALL BACKING PAD AND SANDING DISC
Disconnect tool from power source. Set the tool on paddle lever. Wire brushes are equipped with your fingers.
SPINDLE LOCK
SPINDLE
RUBBER BACKING
PAD
SPIN-ON WIRE BRUSH
SANDING DISC
LOCK NUT
Operating Instructions... backing pad be used to guide and balance the tool can cause...
Operating Instructions - Page 10
... switch life. MOTOR HOUSING RELEASE LEVER (Model 1894-6 only)
Your tool is difficult to control.
Use disc grinding wheels for fast grinding of the grinder.
The discs vary as to size and... dangerous stresses
on the wheel.
If the angle is too steep, the pressure is determined by controlling the pressure and keeping the angle between wheel and workpiece at times both "...
Operating Instructions - Page 11
... discs.
WARNING
Avoid bouncing and snagging the wire brush, espe- This can cause wire breakage.
3.
BRUSHING PRESSURE 1. Apply the brush to 15° angle while sanding so that only about 1" of the...If the disc (accessory) is held flat or the back edge of control and
kickback. Guide the Disc Sander with crosswise strokes.
If heavier pressures are used , the wires will be ...
Operating Instructions - Page 12
rized Bosch Service Station. TOOL LUBRICATION Your Bosch tool has been properly lubricated and is capable
of these are: gasoline,
carbon tetrachloride, chlorinated cleaning
solvents, ammonia and household
detergents that all tool service be replaced at every brush change , the bearings
should be used. CAUTION
Certain cleaning agents and solvents damage
plastic parts. Some of ...
Parts List - Page 2
...
1 607 000 380 PARTS SET
1 604 011 178 ARMATURE \ 100-120V
1 607 000 704 ON-OFF SWITCH
1 601 106 999 NAMEPLATE \ 26x52 MM
1 607 014 171 CARBON-BRUSH SET
Price group 28 38... 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1
2 2 2 1 1 1 1
http://le11288.le.de.bosch.com/sid/printdirect.asp?ID_PRODUCT=0601852B60&ID_VE... 10/24/2005 Page 2 of 5
Item Quantity Order No.
Parts List - Page 3
... BRUSH HOLDER
1 607 000 C03
GEAR HOUSING
1 607 000 C05
BEARING FLANGE \ Ø 230 MM
1 607 000 383 BEVEL GEAR SET
...1 607 000 354 PUSH-BUTTON
1 607 000 342 RETAINING WASHER
1 600 119 010 C-CLIP
1 600 905 026 DEEP-GROOVE BALL BEARING
2 600 910 001 NEEDLE BUSHING \ Ø 14 MM
Page 3 of 5
1
24
1
19
1
39
1
33
1
1
12
1
12
1
11
1
21
1
14
1
http://le11288.le.de.bosch...
Parts List - Page 4
Page 4 of 5
Page 2
http://le11288.le.de.bosch.com/sid/printdirect.asp?ID_PRODUCT=0601852B60&ID_VE... 10/24/2005
Parts List - Page 5
Page 5 of 5 http://le11288.le.de.bosch.com/sid/printdirect.asp?ID_PRODUCT=0601852B60&ID_VE... 10/24/2005
Bosch 1893-6 Reviews
We have not received any reviews for Bosch yet.