Carvin EQ230 Support and Manuals
Get Help and Manuals for this Carvin item
View All Support Options Below
Free Carvin EQ230 manuals!
Problems with Carvin EQ230?
Ask a Question
Free Carvin EQ230 manuals!
Problems with Carvin EQ230?
Ask a Question
Carvin EQ230 Videos
CARVIN / ?????????????????EQ230/EQ430
Duration: 1:43
Total Views: 4,220
Duration: 1:43
Total Views: 4,220
CARVIN / ???????????? EQ230
Duration: 1:19
Total Views: 1,852
Duration: 1:19
Total Views: 1,852
Popular Carvin EQ230 Manual Pages
EQ430 Product Manual - Page 1
... noise and full 20-20kHz bandwidth with reduced feedback, driver protection and time correction of 1/3 octave constant-Q filters,... flexibility required for both installation and live use the intuitive USB interface (see carvin.com/XD).
System Presets...of each element in your preferred settings to any system. EQ230 / EQ430 Operation Manual
The EQ230 and EQ430 with X-Drive™...
EQ430 Product Manual - Page 2
... Utility Menu Delay Units Delay Memory Security Lockout Password Unit ID Firmware Version 4.C. Computer/Serial Control and Graphic User Interface 5.A. Rear Panel Connections and Features AC power Ground lift switch Audio Inputs Audio Outputs USB
4. Front Panel Controls and Settings 4.A. Introduction and Functions
2. Specifications
7. Software Minimum Requirements Installation 5.B.
EQ430 Product Manual - Page 3
...instructions. CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. The panels of all pro gear, avoid prolonged use , or failure to replacement text on or pinched by this unit.
Carvin will service and supply all parts... OPEN. SERVICING: The user should be walked on the unit for damage due to: natural disasters, accidents, abuse, loss of parts, lack of the problem with a...
EQ430 Product Manual - Page 4
...through access to settings for firmware updating.
^ INPUTS ^ ^ OUTPUTS ^ ^ INPUTS ^ ^ OUTPUTS ^ ^ INPUTS ^ ^ OUTPUTS ^ ^ INPUTS ^ ^ OUTPUTS ^
INPUTS 1 - 4, (XLR or 1/4"): Connect to SYSTEM or UTILITY menus. When using Carvin's XD™... computer using the Balanced XLR jacks the signal has unity gain, 0dB in complex setups. This can be a 6dB loss. Front Panel:
SYSTEM, UTILITY, and EXIT ...
EQ430 Product Manual - Page 5
...HPF/LPF's will be affected. ~ First, turn the unit back ON. You can save a complete setup into the system, reset the system to load a system (-or UP for pg.4, DOWN for pg.2,...multiple systems and recall (load) them later. ~ Press SYSTEM to the "0" or Flat setting, all Input/Output settings. Front Panel:
FREQUENCY BAND SELECTORS (numbered 25 through the menu pages or adjust parameters....
EQ430 Product Manual - Page 6
... allow changes to the Channel screens. Then enter the new password using the Carvin XD™ EQ software. (DOWN for Page 3, or EXIT to return to the Channel screens.
< - Press EXIT to return to the EQ230/EQ430 settings. The limit is 1122. If desired, download updates from 1-16. Page 1 - > DELAY UNITS (Press UTILITY) ~ ~ Press UTILITY...
EQ430 Product Manual - Page 7
...LEVEL (in Hz) and it from one of the selected channel use the UP/DOWN buttons. Channel Settings continued on next page: Limiter, HPF, LPF 7 To adjust a different channel, press it's SELECT ...Meters/mm. (change from the total time available for the EQ230/EQ430 is +12db at maximum to cycle through the channel's other setting screens and parameter selections. Press EXIT at the right side ...
EQ430 Product Manual - Page 8
... and recordings by controlling peaks in dB
L i m i t er: + 20 .0 L P F : S : 20 k H z
Low Pass Filter (High Cut) Frequency
LIMITER:
The Limiter is used to -20.0dB. HPF: Set the High Pass Filter frequency (Low Cut). CHANNEL SCREEN PAGE 3: [press SELECT to access parameters]
Channel selection
Cha n n e l : 1 H P F : 40 Hz
High Pass Filter (Low Cut...
EQ430 Product Manual - Page 9
... EQ430 hardware: CONNECT TO DEVICE 1. You must plug in the USB cable to use with Carvin's XD™ EQ software.
5.A. Run the Setup.exe file to the program.
5. You will be installed to the EQ230 or EQ430 hardware, the device should be asked if you turn on your Hard Drive. It is recommended to...
EQ430 Product Manual - Page 10
... on your computer from the computer to the EQ230/EQ430 hardware memory.
Select the COM port for the device. Save the file in a known location on your computer and double click.
10 The actual COM PORT can be uploaded from www.carvin.com/XD. 2. Download new firmware to your computer. 3. To perform a EQ230/EQ430 firmware update: 1. -
EQ430 Product Manual - Page 11
...to be retrieved later. 5.C. All changes made on this button to the EQ230/EQ430. COPY and PASTE: Copy settings from one channel to receive the copied settings and click PASTE. Click on 1, 2, 3 or 4 to access each...later loaded back in a file on the DELAY button to the EQ230/EQ430.
SYNC TO SOFTWARE (top right area of screen) Complete setups can be copied (1-4) and click COPY.
EQ430 Product Manual - Page 12
6. SPECIFICATIONS: CARVIN X-Drive EQ430/EQ230
INPUTS: Female XLR connectors: 10kOhm, balanced 1/4" connectors: 10kOhm, unbalanced Maximum Input +18 dBu OUTPUTS: Male XLR connectors: 150 Ohms, balanced 1/4" connectors: 150 Ohms, unbalanced Maximum Output +18 dBu Dynamic Range 114dB unweighted 20Hz - 20kHz Frequency Response 20Hz - 20kHz Distortion (THD)
Carvin EQ230 Reviews
We have not received any reviews for Carvin yet.