Cub Cadet 3X 30 inch PRO Support and Manuals
Get Help and Manuals for this Cub Cadet item
View All Support Options Below
Free Cub Cadet 3X 30 inch PRO manuals!
Problems with Cub Cadet 3X 30 inch PRO?
Ask a Question
Free Cub Cadet 3X 30 inch PRO manuals!
Problems with Cub Cadet 3X 30 inch PRO?
Ask a Question
Popular Cub Cadet 3X 30 inch PRO Manual Pages
Operation Manual - Page 1
... TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. The terms "snow thrower" and "snow blower" may vary by model. Not all features in this product. Form No. 769-11510D (May 17, 2018) NOTE: This Operator's Manual covers several models.
Safe Operation Practices • Set-Up • Operation • Service • Troubleshooting
Operator's Manual
Snow Blower
2-Stage...
Operation Manual - Page 3
... safety systems are certified to operate on the handles. Do not overload machine capacity by an authorized service dealer to ensure that all components and replace with factory setting of parts which do not meet the original equipment specifications may include the following emission control systems: Engine Modification (EM), Oxidizing Catalyst (OC), Secondary Air Injection...
Operation Manual - Page 5
... be sure that this manual, all models. We reserve the right to provide excellent performance when properly operated and maintained. If applicable, the power testing information used to Set-up , operate and maintain your machine.
Refer to Chute Assembly Options.
• Complete snow thrower assembly according to identify your specific unit. Refer to establish...
Operation Manual - Page 11
...31.
3. Place chute assembly onto chute base and chute control head onto chute support bracket.
Assembly & Set-Up
11 Ferrule may need to be to chute control head with cotter pin ...two surfaces line up. See Figure 2-37, Detail "A" for models without hydro transmission or Detail "B" for models with Crank Chute Control - Make sure to Set-Up (page 13).
(b) (b)
Figure 2-32
Figure 2-35...
Operation Manual - Page 12
... E-Z Chute™ does not require any installation. Push chute control rod toward the control ...Set-Up (page 13).
12
Section 2 - STOP Continue to Set-Up (page 13). Assembly & Set-Up Push rod as possible, keeping holes in Step 1. See Figure 2-39. NOTE: For units equipped with manual... be to the left of control rod to chute support bracket with middle hole in chute control input and ...
Operation Manual - Page 13
... purposes. If not provided, make sure to the provided skid shoes. 1. Standard 1. See Figure 2-48.
(b) (a)
(b) (a)
Figure 2-48 2. See Figure 2-49. Skid Shoes (If Applicable)
Select models require the installation to store them from the sides of auger housing. Assembly & Set-Up
13
Operation Manual - Page 14
... desired position. Loosen four hex nuts (a) (two on each drift cutter to be maintained at the factory set roughly 1/8" below the shave plate. Move skid shoes to desired height.
3. Retighten hex nuts (a) and ...auger housing. Adjustments
Chute Assembly
NOTE: For models with 2-Way/4-Way or Electric Chute Directional Control and/or models with manual chute tilt, including E-Z Chute™, the...
Operation Manual - Page 15
... to verify your Engine Operator's Manual.
3.
Perform all adjustments to ...engaged for ALL moving parts to your equipment ...shoes. On E-Z Chute™ models, loosen the rear
hex screw... tighten the shift cable.
5.
Assembly & Set-Up
15 Reinstall and tighten the carriage bolts...position, walk to run until it rests on all instructions below. Shift Cable (If Equipped)
If full range...
Operation Manual - Page 16
...Manual. 2. Retighten upper hex screw. 5.
See Figure 2-59.
(a)
(b)
Figure 2-59 3. Refer to the Engine Operator's Manual... for information on the back of
the transmission is released and in the shift lever.
If equipped with a shift lever, with hydro transmission.
Check adjustment of adjustment. Drive Control (Models... Operator's Manual. 2....models with drive control...
Operation Manual - Page 18
...to operating your engine. Read and follow all instructions carefully and perform all adjustments to the reverse...Manual covers several models. Snow thrower features may differ from the operator's position. Not all snow thrower models and the snow thrower depicted may vary by model...Adjustment section on carburetor and aids in the Assembly & Set-Up section prior to the OFF position.
(a) (b)...
Operation Manual - Page 19
... with Hydro Transmission -
Figure 3-5
*On select models, the drive control lever also locks the auger ... IMPORTANT: Refer to the Auger Control information in the Assembly & Set-Up section prior to the upper handle.
See Figure 3-7. Controls ...or to stop augers and wheel drive. Read and follow all instructions carefully and perform all units except the 800-series hydro.
Figure...
Operation Manual - Page 22
... should be rotated 180° to use the other end to Replacing Shear Pins on page 21. Troubleshooting
Engine Fails to Propel Itself
1. See Engine Operator's Manual.
2. See Engine Operator's Manual.
3. See Engine Operator's Manual.
Repair as directed in need of extension cord to Service section on page 24. Refer to electric starter outlet and other edge...
Operation Manual - Page 24
.../E-Z Chute™
Refer to Assembly & Set-up section (page 14) for instructions on adjusting shift rod. See Figure 4-9.
(a) (a)
Figure 4-10 NOTE: On models equipped with second hole in ¼ turn... so: 1. See Figure 4-8.
(a)
(a)
Figure 4-9 2. Service
Auger Belt Replacement (500, 600 and 800 Series)
To remove and replace auger belt, proceed as shown in the rear accelerator. Do...
Operation Manual - Page 25
... after installing a replacement auger ...following instructions in Assembly & Set-...service dealer to run until it rests on page 25.
2. Remove belt from bolt. 3. Tip the snow thrower up and out from around the engine pulley (b), and away from underside of belt.
8.
See Figure 4-4.
6. Set it between support bracket and auger pulley. See Figure 4-13.
(a)
(b)
Auger Belt Replacement...
Operation Manual - Page 26
... Transmission (If Equipped)
NOTE: See your authorized service dealer to be replaced. Single Speed Transmission (Models Equipped with drive control lever engaged, and performing drive control cable adjustment fails to correct problem, the friction wheel may need to have the single speed transmission serviced or contact Customer Support for signs of wear or cracking. Reinstall the...
Cub Cadet 3X 30 inch PRO Reviews
We have not received any reviews for Cub Cadet yet.