CyberPower PDU20SWHVT10ATNET Support and Manuals
Get Help and Manuals for this CyberPower item
View All Support Options Below
Free CyberPower PDU20SWHVT10ATNET manuals!
Problems with CyberPower PDU20SWHVT10ATNET?
Ask a Question
Free CyberPower PDU20SWHVT10ATNET manuals!
Problems with CyberPower PDU20SWHVT10ATNET?
Ask a Question
Popular CyberPower PDU20SWHVT10ATNET Manual Pages
User Manual - Page 2
...19
Firmware Upgrade 20 ATS PDU 20 LCD ...2 1 RMCARD 23
Troubleshooting 25 Conformance Approvals 26 Customer Service & Warranty 27 Appendix A-Hyper Terminal 28 Appendix B-Power Device Network Utility 29 Table of Contents
Overview 1 Model List 1
Product Contents 2 For 1U Models 2 For 2U Models 3
Product Features 4 Front/Rear Panel Description (1U 15A Models 4 Technical Specifications...
User Manual - Page 3
...missing parts, ...Model...installed in certain regions.
Please contact your local CyberPower sales team for technical support...install an ATS PDU or associated wiring or equipment during a lightning storm. • Ensure that is unstable or unavailable, the ATS PDU will switch to the second power source to constantly provide power to local power condition.
Users can configure power settings...
User Manual - Page 20
... see the RMCARD205 User Manual.
Deviation
Sensitivity
Overload
Threshold
Load
Device
Near Overload
Configuration Bank/1/2/3
Threshold
Low Load
Threshold
Immediate On
Delay On
Outlet Control
Device Bank/1/2/3
Immediate Off All/Outlet 1-N
Delay Off
Reboot
Delay Reboot
Brightness
LCD Settings Scroll Mode
Screen Off
18 Enter the user name and password of the SNMPv1...
User Manual - Page 21
... Edition Client User Manual).
2. Red
Overload. Off
The ATS PDU power is on every computer or server for detailed instructions. Tx/Rx
On (Green) Flashing
The ATS PDU power is off . Outlet
On
The outlet is abnormal. Computer Configuration
1. Install PowerPanel Business Edition Client on and providing power. Configure the settings in a server closet...
User Manual - Page 22
... of the file name but is where the version number in the filename is given. Setup the COM port settings using the following steps to "C:\". 3. ATS PDU
Update the following file to select ATS PDU upgrade.
20 Download the latest firmware from www.cyberpower.com. 2. Use the included RJ45/DB9 serial port connection cable. Press...
User Manual - Page 23
.... Setup the COM port settings using the following values. * Bits per second: 38400 * Data bits: 8 * Parity: None * Stop bits: 1 * Flow control: None 21 cpsatslafw_xxx.bin Note that the Ymodem protocol and file "C:\cpsatsmafw_xxx.bin" are selected in the filename is not part of the ATS PDU, and the other end to upgrade the firmware. - Note...
User Manual - Page 27
... figure. Faulty breaker
Solution
Reset Breaker, check the plug to connected equipment
1.
If the problem remains, contact technical support. Firmware Upgrade
Confirm Upgrade Firmware message window 8. If the firmware upgrade is not
properly plugged in the main window
Troubleshooting
Problem
Possible Cause
ATS PDU outlets do not provide power to insure its connected correctly...
User Manual - Page 28
...upgrades, and other regions: Please visit our website for purchasing a CyberPower product.
In a domestic environment this equipment. Prompt product registration entitles coverage under the Limited Warranty and also allows the opportunity to be required to cause harmful interference in accordance with installation, troubleshooting... Tech Support department with the instruction manual, may...
User Manual - Page 29
...code), without the use of the Product or any data that
was connected to it were connected to properly wired and grounded outlets (including compliance with the Product, such as a result of the failure or the restoration of data or records, or the reinstallation of the defect.
CyberPower will repair or replace..., instruction manual, or...You Get Service? 1.
... support... installation ...Problems...
User Manual - Page 30
... MAC Address: 00-0C-15-00-00-01 1. DHCP: Enabled 5. Name: PDU15SW10ATNET 2. Location: Server Room 3. Reset ATS PDU 2. Reset ATS PDU (TCP/IP Settings Reserved)
28 Setup the COM port settings using the following values. * Bits per second: 38400 * Data bits: 8 * Parity: None * Stop bits: 1 * Flow control: None
Note: The session will timeout...
User Manual - Page 33
... appropriate device selected from the Equipment List, open the Network Settings menu (shown in Figure 9). Network Setting Menu (Device Setup) Step 3. Authentication screen
Advanced Settings
Timeout Settings The Timeout Setting (Shown in Figure 10). [Edit=>Timeout Settings] is "cyber". Note: The default username is "cyber" and the default password is used to 60 seconds. Figure 10. Timeout...
Firmware Upgrade Instructions - Page 1
... PC and select a name and icon for Hyper Terminal to interface with the ATS PDU, the PC/server must be connected directly to "C:\" 3. ATS_FW_Upgrade_Procedure
By upgrading the Firmware, you can obtain new features and updates improvements to connect ATS and use the command "@NEW".
Firmware Upgrade Putty Instructions - Page 1
...ATS PDU upgrade.
ATS PDU Firmware Upgrade Instructions (Example using following values. * Bits per second: 38400 * Data bits: 8 * Parity: None * Stop bits: 1 * Flow control: None
Cyber Power Systems, Inc. Press "1" to update.
Type the command @new. www.cyberpower.com Verify it is performed, please setup the COM port settings using ExtraPutty)
By upgrading the Firmware, you can...
LCD Firmware Release Note 1.50 - Page 1
.../30/2015):
Bug Fixes
First LED will be able to update since the ATS powered up. Ver. 1.2 (Release Date: 01/09/2015):
Bug Fixes
Source switch rarely result in one bank model.
Ver. 1.3 (Release Date: 01/20/2015):
Feature Improved
Support 32A model (Europe model). Release Note of ATS LCD Board Ver. 1.5 (Release Date: 04...
Mainboard Firmware Release Note 1.07 - Page 1
Ver. 1.04 (Release Date: 01/20/2015):
Feature Improved
Support 32A model (Europe model). Improve the algorithm of "break before voltage threshold and frequency deviation value....power (preferred source should be able to update since the ATS powered up. Ver. 1.05 (Release Date: 04/07/2017):
Bug Fixed
The LCD information might not be set to avoid probable cross-connection of sources when...
CyberPower PDU20SWHVT10ATNET Reviews
We have not received any reviews for CyberPower yet.