Fluke 9100S-D-156 Support and Manuals
Get Help and Manuals for this Fluke item
View All Support Options Below
Free Fluke 9100S-D-156 manuals!
Problems with Fluke 9100S-D-156?
Ask a Question
Free Fluke 9100S-D-156 manuals!
Problems with Fluke 9100S-D-156?
Ask a Question
Popular Fluke 9100S-D-156 Manual Pages
Product Manual - Page 2
... the product, with its functional specifications for 90 days and that the failure was caused by accident or abnormal conditions of repairs/replacement parts when product purchased in one year for the repair and return transportation charges (FOB Shipping Point). Parts, product repairs, and services are warranted for damage in another country. Fluke assumes no authority to every buyer...
Product Manual - Page 3
...Introduction 1 1.2 Symbols Used 1 1.3 Safety Information 3
1.3.1 Warnings...3 1.3.2 Cautions...4 1.4 Authorized Service Centers 5
2 Specifications and Environmental Conditions 9
2.1 Specifications 9 2.2 Environmental Conditions 9
3 Quick Start 11
3.1 Unpacking 11 3.2 Set-up...11 3.3 Power...11 3.4 Setting the Temperature 11
4 Parts and Controls 13
4.1 Rear Panel 13 4.2 Side View 14...
Product Manual - Page 4
9100S Dry-Well Calibrator
6.3.1 Scan Control 22 6.3.2 Scan Rate...22 6.4 Set-point Resistance 22 6.5 Secondary Menu 23 6.6 Heater ... Commands 32
8 Test Probe Calibration 35
8.1 Calibrating a Single Probe 35 8.2 Dry-well Characteristics 35
8.2.1 Stabilization and Accuracy 35
9 Calibration Procedure 37
9.1 Calibration Points 37 9.2 Calibration Procedure 37
9.2.1 Compute DELTA ...
Product Manual - Page 9
...'s range. Calibrations may be set -point memory ●● Adjustable readout in °C or °F
The temperature is accurately controlled by Fluke's digital controller. The LED front panel continuously shows the current well temperature.
This dry-well calibrator was designed for portability, low cost, and ease of the calibrator as described in the instruction manual.
1.2 Symbols...
Product Manual - Page 12
... the instrument when the instrument is set to 375°C and the display reads 375°C, the well is not installed correctly.
●● Always replace the power cord with one of ...with the inserts in place;
9100S Dry-Well Calibrator
Safety Information
BURN HAZARDS
●● DO NOT turn off .
●● The high temperatures present in dry-wells designed for operation at 300...
Product Manual - Page 13
... Section 11, Troubleshooting, on your Fluke product:
5
MyFlukeStore Shop for optimum durability and trouble free operation, it are sensitive instruments that the probe handle temperature limit is important to the safety and proper operation of the calibrator.
●● DO NOT drop the probe sheath in the air above the instrument.
1.4 Authorized Service Centers
Please...
Product Manual - Page 14
9100S Dry-Well Calibrator
Authorized Service Centers
6
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664
Product Manual - Page 15
Before You Start
Authorized Service Centers
E-mail: antng@singa.fluke.com When contacting these Service Centers for support, please have the following information available:
●● Model Number ●● Serial Number ●● Voltage ●● Complete description of the problem
7
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664
Product Manual - Page 17
... (Installation) CATEGORY II, Ploution Degree 2 per IEC1010-1
Sensor burnout protection, over-temperature cutout, and electrical fuses
250 V 3 A FF (very fast acting) NO USER SERVICEABLE PARTS
2.2 Environmental Conditions
Although the instrument has been designed for Fluke products online at equal depths within ±10% of nominal ●● vibrations in the calibration environment...
Product Manual - Page 19
... carefully and inspect it Software and User's Guide
3.2 Set-up
Place the calibrator on a flat surface with at : www.
.com 1.888.610.7664
Observe that the following components are present:
●● 9100S Dry-well ●● Power Cord ●● User's Guide with Report of Calibration ●● RS-232 Cable ●● 9930 Interface-it...
Product Manual - Page 35
... parameter is indicated by,
LF
Flashes for Fluke products online at the factory and must not be adjusted to improve the accuracy of the parameter may restore these constants and their settings with the instrument manual. The correct setting of the instrument calibration constants from the factory set the parameter to the
27
MyFlukeStore Shop for...
Product Manual - Page 45
.... Repeat step 2 for Fluke products online at each of say ±0.3°C over the range 175°C to 325°C but other two set -point. The thermometer used must be obtained for the calibration. Using this procedure the dry-well can be able to measure the well temperature with the set -point error at : www.
.com...
Product Manual - Page 46
9100S Dry-Well Calibrator
Calibration Procedure
9.2.1 Compute DELTA A = T3 − T2 B = T2 − T1
... temperature and set-point resistance at 50.0 °C T2 and R2 are the measured temperature and set-point resistance at 200.0 °C T3 and R3 are the measured temperature and set-point resistance ...Section )
38
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664
Product Manual - Page 47
... drywell does not pass specification at all set-points, repeat the Calibration Procedure.
39
MyFlukeStore Shop for DELTA (delta), R0 (rzero), and ALPHA (alpha) into the instrument (see Section 6.12, Calibration Parameters on page 27 and Figure 5 on page 21).
9.2.3 Accuracy and Repeatability Check the accuracy of the dry-well at : www.
.com 1.888.610.7664 Calibration...
Product Manual - Page 51
... 7 - a heater error Initialize the system by performing the Factory Reset Sequence. Troubleshooting
Troubleshooting Problems, Possible Causes, and Solutions
11 Troubleshooting
This section contains information on with the Scan Rate set low (if unit seems to be responding too slowly). Allow the instrument to be solved, contact an Authorized Service Center (see Section , Calibration Parameters...
Fluke 9100S-D-156 Reviews
We have not received any reviews for Fluke yet.