Harbor Freight Tools 61483 - 13 in. Floor Mount Drill Press Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 61483 manuals!
Problems with Harbor Freight Tools 61483?
Ask a Question
Free Harbor Freight Tools 61483 manuals!
Problems with Harbor Freight Tools 61483?
Ask a Question
Popular Harbor Freight Tools 61483 Manual Pages
User Manual - Page 2
...rain. Form habit of contents
Safety 2 Specifications 6 Setup 6 Operation 9
Maintenance 12 Parts List and Diagram 14 Warranty 16
SAFETy
SETUp
OpERATION
WARNING SyMBOLS AND DEFINITIONS This is ...
For technical questions, please call 1-800-444-3353. Obey all safety warnings and instructions.
Indicates a hazardous situation which it was not designed. MAKE WORKSHOP KID PROOF with...
User Manual - Page 3
... SECURE WORK. Follow instructions for recommended accessories....Consult the owner's manual for lubricating and changing accessories....repaired or replaced.
20. CHECK DAMAGED PARTS. Feed work when practical. WEAR PROPER APPAREL. Keep tools sharp and clean for alignment of moving parts, binding of moving parts...plugging in off position before servicing; SAFETy
SETUp
General Tool Safety Warnings ...
User Manual - Page 4
... the manufacturer may not provide adequate protection. Do not modify the plug provided - Repair or replace damaged or worn cord immediately. The outlet must be properly installed and grounded in accordance with or without yellow stripes is green with all codes and ordinances. 9. Use recommended speed for up to 125 V~ and up to a live...
User Manual - Page 5
... the operator.
SAFETy
SETUp
Drill press Safety Warnings...or for a replacement.
13. SAVE THESE INSTRUcTIONS. People with ...instruction manual cannot cover all possible conditions and situations that common sense and caution are doing and use this manual...Prepare to ensure medical problems are specially designed to.... (California Health & Safety Code § 25249.5, et seq...
User Manual - Page 6
... section at the beginning of this manual including all text under subheadings therein before set up or use of the Drill Press and any procedure in the following pages, refer to a flat, level, solid floor location capable of supporting the weight of this manual. Verify that the intended installation surface has no hidden utility lines...
User Manual - Page 7
...Support Assembly over the Column and hold it also rotates freely all parts...Support Assembly easily travels up the Column to within 6″ of the Rack in this position while replacing the Collar on the Support...Table to protect the Chuck nose.
4. Installing the chuck
1. pulley cover Knob
Attach ... the Collar Set Screw, and test the assembly again.
9. SAFETy
SETUp
Table and Support Arm to ...
User Manual - Page 8
...to the belts. Deflection Distance = 1/2"
Figure A 5.
Functions
SETUp
OpERATION
MAINTENANcE
Page 8
For technical questions, please call 1-800-444-3353. SAFETy
Installing the Drive Belts
1.
Use the Belt Tension Locking Knobs to ...Item 61483 Undo the Belt Tension Locking Knobs (14) on page 10), and install the Belts (53, 88) in the positions corresponding to
lock the Motor Pulley in ...
User Manual - Page 9
... (C). Tool Set Up
SAFETy
SETUp
OpERATION
TO ...manual including all normal operations the Table angle should be locked in this position.
1. Raise or lower the Table by loosening the Arm Locking Handle. Figure B: Table Adjustments
Setting Drilling Depth
See Figure c.
The table assembly, arm and rack (B), move freely and close instantly. See Figure B.
4. Operating Instructions...
User Manual - Page 10
...until it must be replaced.
360
430
630
760
1430
1620
2580
3600
Figure D: Belt Speed Settings
The table above shows the belt arrangements for illustrations.
1.
SAFETy
SETUp
changing Drill Speed
See ...bits. Item 61483 Insert the drill bit approximately 1″ into a hole on the Chuck. Installing the Bit
cAUTION! Do not remove a drill bit until the bit is correct when the ...
User Manual - Page 11
....
2. Clamp or bolt the vise to bring the drill bit down firmly against column
General Operating Instructions
1. Figure E: Bracing workpiece against the table to prevent it from turning.
10. Step back, ... cord must not be caused if the workpiece is to possible damage. SAFETy
SETUp
Workpiece and Work Area Set Up
1. There must reach the work area without creating a tripping hazard or...
User Manual - Page 12
..., have the problem corrected before performing any other damage.
2. AFTER USE, wipe external surfaces of the tool. Replace a belt if damaged, following the instructions under Installing the Drive Belts on page 8.
SETUp
OpERATION
MAINTENANcE
Page 12
For technical questions, please call 1-800-444-3353.
SAFETy
Maintenance and Servicing
procedures not specifically explained in...
User Manual - Page 13
... qualified technician replace brushes. 3. OpERATION
MAINTENANcE
Record product's Serial Number Here: Note: If product has no other loads. 3. pLEASE READ THE FOLLOWING cAREFULLy
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.
SAFETy
SETUp
Troubleshooting
problem
Tool will not start. Properly install belt(s). See...
User Manual - Page 14
...SETUp
parts List and Diagram
parts List
part
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
Description
Base Column Support... Lock Knob Scale Label Rivet 2×3 Pointer Collar Collar Set Screw M8×10 Axis Pin Helical Gear Support Arm Locking Handle Handle Cover Work Table Socket Head Cap ...
User Manual - Page 15
SAFETy
SETUp
Assembly Diagram
90 89 89 88
87
86
91 85 84
85
54
84
83
53
74
52
92
37
57
51
93
82
76 ...
User Manual - Page 16
... in no defect, or that this warranty, the product or part must be liable for death, injuries to state.
3491 Mission ...us with a replacement. This warranty gives you specific legal rights and you . We will either repair or replace the product at... abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or...
Harbor Freight Tools 61483 Reviews
We have not received any reviews for Harbor Freight Tools yet.