JET Tools J-1600R Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools J-1600R manuals!
Problems with JET Tools J-1600R?
Ask a Question
Free JET Tools J-1600R manuals!
Problems with JET Tools J-1600R?
Ask a Question
Popular JET Tools J-1600R Manual Pages
User Manual - Page 1
Radial Arm Drill Press
Models J-1600R, J-1600R-4
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
1
Part No. This .pdf document is bookmarked
Operating Instructions and Parts Manual
5-ft. M-320038 Revision G3 05/2014 Copyright © 2014 JET
User Manual - Page 2
...our tools needs service or repair, please contact Technical Service by a 90 day limited warranty against manufacturers' defects. Motors; Pro-Duty Air Tools 2 Year -
EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED.
Metalworking Machinery; Shop Tools; For complete, up-to the JET brand.
2 JET Parallel clamps; Manual...
User Manual - Page 3
...3.3 Safety Instructions for Drill Presses ...6 4.0 Specifications ...7 4.1 Machining Capacities ...8 4.2 Machine Environment...8 4.3 Power Supply Requirements...8 4.4 Overall Dimensions, J-1600R ...9 5.0 General Features and Terminology, J-1600R 10 6.0 Set-Up and Assembly ...12 6.1 Floor Diagrams for J-1600R...26 12.1 General Cleaning ...26 11.2 Lubrication...26 13.0 Replacement Parts - roughing...
User Manual - Page 5
...comply with ANSI Z87.1 specifications could result in damp ...instructions in moving parts.
Failure to get caught in operator's and parts manual when changing accessory tools or parts.
-Never modify the machine without consulting JET
Read and follow instructions in place.
- Eye wear shall be set... machine tools with guards removed.
5. When setting up , used and serviced properly....
User Manual - Page 7
4.0 Specifications
The JET Model J-1600R is mounted on an arm and can slide along arm, total 44-7/8" (1140 mm) Feed rates (distance per revolution six at 0.003 - 0.038 in/rev Base surface to spindle, maximum (no tooling 63" (1600 mm) Base surface to spindle, minimum (no tooling 15" (380 mm) Column to spindle center distance, maximum 62...
User Manual - Page 13
... installed and running properly. Missing parts, if any damage immediately to your distributor. Read the instruction manual thoroughly for shipping damage. Failure to make sure all parts are intact. Contents of Shipping Container
(see Figure 8)
1 Radial Arm Drill Press (not shown) 6 Leveling Pads 1 Tool Box, containing:
1 Grease gun 1 Oil bottle 1 Tapered drift 1 Adjustable wrench 1 Set...
User Manual - Page 14
...support pieces if machine is properly lubricated at all points recommended in future.)
9. Surfaces of lifting
3. See section 12.0 Maintenance, for service. Figure 9: Method of the machine have been treated with machine service and national and local codes...guide, and mount the nuts to exposed metal surfaces. Remove the bolts holding machine to instructions... 6.3 Machine Set-Up
1. ...
User Manual - Page 15
...of this manual. If any...set-up requirement should be followed, exclusively. This machine must be connected to either a 230V or 460V, 3phase service branch.
Model J-1600R...service disconnect with tooling on the outside of arrow cast into pump assembly.
This includes fuse replacement, if required.
The transformer can be supplied by your licensed installing or servicing...
User Manual - Page 17
... are engaged before using a T-slot system set-up.
8.2 Tool insertion
The Model J-1600R uses a No. 5 Morse taper in removing or inserting any work piece, and box table if used to lock the head to the arm, the arm to the column, and the column to machine operator. The service box should it fall out during...
User Manual - Page 18
... by pushing UNLOCK button on support column
1.
These recommendations are absolutely....
8.8 Setting spindle speed
Spindle speeds are recommended drill and tap sizes for any specific drilling operation...tooling, coolant and/or workpiece suppliers to determine best spindle speed to use for the various speeds which you need to drill press itself.
8.7 Rotating arm on front of this manual...
User Manual - Page 19
...determined by consulting appropriate machinery handbooks or by consulting with your tooling, coolant and workpiece suppliers. There will slip when travel ...set to disengage power feed when a pre-set using power feed system
Plan for changing.
8.11 Feed methods
The J-1600R has three feed methods: power feed, hand feed and fine hand feed. However, while you want to instructions in HI setting...
User Manual - Page 20
...can be set to its service branch correctly, there will feed drill into disengaged (toward the left hand tooling. If ...spindle will move the quill and spindle and perform manual drilling or other machining operations.
8.15 Fine hand...1600R was connected to Figure 14.
1. Turn drill press power switch to desired direction.
4. This is set (out of drill head. Always be a service...
User Manual - Page 21
...more information. When servicing tooling or other switches on... drive motor.
The switch is a problem internally (such as lack of current...service disconnect lever in disengaged position (all the way to coolant nozzle using handle at this occurs, a licensed electrician should locate and re-set...lever is used to Forward.
5. It is installed, you have turned off power at left of...
User Manual - Page 24
... lever to trip. 10.0 Troubleshooting the J-1600R
Trouble
Spindle overloads, causing relay to highest gear. 4. Table 3
If drill bit gets broken in the control box. Replace fuse if needed. Verify proper...power, wait three minutes after spindle stops turning, then push re-set on the relay in spindle: 1.
Replace fuse in compliance with pliers. 5. consult appropriate feed and speed rate...
User Manual - Page 28
... Model Number and Serial Number of your machine available when you quickly and accurately.
13.1.1 Riser Mechanism: Exploded View
28 To order parts or reach our service department, call will allow us to serve you call 1-800-2746848, Monday through Friday (see our website for business hours, www.jettools.com). J-1600R Radial Arm Drill
Replacement parts...
JET Tools J-1600R Reviews
We have not received any reviews for JET Tools yet.