JET Tools MBS-1323EVS-H Support and Manuals
Get Help and Manuals for this JET Tools item
This item is in your list!
View All Support Options Below
Free JET Tools MBS-1323EVS-H manuals!
Problems with JET Tools MBS-1323EVS-H?
Ask a Question
Free JET Tools MBS-1323EVS-H manuals!
Problems with JET Tools MBS-1323EVS-H?
Ask a Question
Popular JET Tools MBS-1323EVS-H Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
Horizontal Dual Mitering Band Saw
Models: MBS-1018-1, MBS-1018-3
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
1
Part No. M-413410 Edition 1 10/2016
Copyright © 2016 JET
User Manual - Page 2
...and other part that is damaged should be properly repaired or replaced.
17. Before further use extreme caution and replace the guards immediately after completion of moving parts. Do ..., blade guides and thrust bearings.
27. Before operating this manual. Maintain tools with all times when the machine is properly grounded.
1.0 IMPORTANT SAFETY
INSTRUCTIONS
WARNING - Replace the warning...
User Manual - Page 4
...
Section
Page
1.0 IMPORTANT SAFETY INSTRUCTIONS ...2 2.0 Table of contents...4 3.0 About this manual ...5 4.0 Specifications ...6
4.1 Base hole centers...7 5.0 Setup and assembly...8
5.1 Shipping contents ...8 5.2 Unpacking and cleanup ...8 5.3 Installation ...8 6.0 Electrical connections ...8 6.1 GROUNDING INSTRUCTIONS ...9 6.2 Voltage conversion (MBS-1018-3 only)...9 6.3 Extension cords...
User Manual - Page 5
... online http://www.jettools.com/us/en/service-and-support/warranty/registration/ The specifications in this document. Read and understand the entire contents of continuous improvement, JET reserves the right to comply may cause serious injury! This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown.
User Manual - Page 8
... or time-delay fuse marked "D". Local codes take precedence over recommendations.
8 Install material stop into front hole in table, as shown in Figure 9-1. Use lifting straps that the MBS-1018-3 band saw 1 Tool box containing:
4 Leveling pads 4 Hex cap bolts, 1/2 x 2 in. 4 Hex nuts, 1/2 in Figure 7-9.
8. Remove all assembly instructions before attempting assembly. Read and understand...
User Manual - Page 9
... accordance with all local codes and ordinances. This tool is the equipment-grounding conductor. The plug must be plugged into a matching outlet that have been tripped in electrical box.
3.
if it is heavy enough to carry the current your product will be connected. Improper connection of this tool. If repair or replacement of power and...
User Manual - Page 10
... knobs before making adjustments, unless indicated otherwise.
7.1 Blade installation and removal
Refer to provide greater bearing support, eliminating bearing wear and extending blade life. Retighten nut (H1). Figure 7-2: blade guide bearing adjustment
7.4 Blade tension and tracking
Refer to suit blade thickness: 1. To replace blade:
1. Disconnect machine from power source. 2. Reinstall...
User Manual - Page 15
...require no further attention.
10.3 Belt replacement
De-tension belt (see sect. 7.5). Start cut on the same or similar workpiece.
5. Keep the same settings and begin a second cut with ... prepared to provide very specific instructions regarding the best blade (and coolant or cutting fluid, if needed .
The workpiece should be adequate for regular service.
10.0 User-maintenance
...
User Manual - Page 16
... feed pressure (hard spots).
Adjust guide bearing clearance to proper level. Replace blade.
10.4 Additional servicing
Any additional servicing should be performed by reducing spring .... Gradually increase blade tension. Blade guide assembly is square with blade.
Increase feed pressure by authorized service personnel.
11.0 Troubleshooting MBS-1018 Band Saw
Symptom
Possible Cause
...
User Manual - Page 17
...Model Number and Serial Number of blade Teeth missing/ripped from JET. Tighten blade guide bearing bracket. Workpiece vibrating. Pump motor is binding in the cut. Screen/filter on blade.
Belt is loose. To order parts or reach our service...coolant flow
Excessive noise or vibration Tension mechanism won 't slide. Replace with coarse tooth pitch; feed too fast.
Tighten impeller. ...
User Manual - Page 19
...30206 Bearing 30206 1 41 TS-0267121 Set Screw 1/4"×3/4 3 42 EHB916V-42 ...Ball 3/16 2 49 TS-0270061 Set Screw 5/16"-18×5/8 1 50...65 2 66 EHB916V-66 Valve...1
19 Parts List
Index No Part No
Description
Size
Qty
1 EHB916V-249... Screw 3/8x2-1/2 1 12 TS-0271031 Set Screw 3/8"x3/8 1 13 EHB916V-13 Spindle... Copper ...1 23 TS-0267041 Set Screw 1/4"x3/8 1 24 TS...
User Manual - Page 20
... Motor Fan Cover 1 EHB1018V-95MF ...... Upper Guard 1 109 MBS1018-1-109 ........ Bracket RH ...4 134 EHB1018VM-134 ...... Run Capacitor (for MBS-1018-1 600μF 125VAC 1 EHB1018V-95MFC ... Gear Box Pulley 1 113 TS-0270021 Socket Set Screw 5/16-18×5/16 1 114 EHB916V-114 Key 5x5x40 mm 1 118 TS-0720081 Lock Washer 5/16 2 119 EHB916V...
User Manual - Page 21
...JET Logo (not shown 203 x 84mm 1
21 Collar ...2 138 TS-0267021 Set Screw 1/4"×1/4 2 139 EHB916V-139 Wire Brush...1 140 EHB1018V-140 ......... Brush Holder 1 141 TS-0207021 Socket Head Cap Screw 1/4"×20×5/8 2 142 TS-0680021 Flat Washer 1/4"x19x2.0 2 144 EHB916V-144 Guide... Index No Part No
Description
Size
Qty
136 EHB916V-136 Carbide Guide 4 137 ...
User Manual - Page 24
...8 285 TS-0267071 Set Screw 1/4"-20×...Part No
Description
Size
Qty
254 EHB1018VM-254 ...... Support Seat 1 263-2 ......... Shaft 7/8 1 292 EHB1018V-259 ......... Support Block 1 296-1 ......... Screw w/Nut 1 297 EHB916V-261 Knob ...1
24 Knob ...1 291 EHB1018V-258 ......... Special Washer 1 256 EHB1018VM-256 ...... Sliding Surface 1 273 TS-0267071 Socket Set...
User Manual - Page 30
...specifications listed in interest to parts, fittings, and accessory equipment which varies in your local distributor or visit the JET website. Manual Hoist Accessories; Warehouse & Dock products; Hand Tools... of our tools needs service or repair, please contact Technical Service by a 90 day limited warranty against manufacturers' defects. JET has Authorized Service Centers located ...
JET Tools MBS-1323EVS-H Reviews
Do you have an experience with the JET Tools MBS-1323EVS-H that you would like to share?
Earn 750 points for your review!
We have not received any reviews for JET Tools yet.
Earn 750 points for your review!