Makita 5007F Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita 5007F manuals!
Problems with Makita 5007F?
Ask a Question
Free Makita 5007F manuals!
Problems with Makita 5007F?
Ask a Question
Makita 5007F Videos
Makita 5007f Circular Saw Motor Housing Sub-Assembly
Duration: 4:10
Total Views: 2,071
Duration: 4:10
Total Views: 2,071
Popular Makita 5007F Manual Pages
Owners Manual - Page 2
... power tools may ignite the dust or fumes.
3. A moment of the tool may result in moving parts.
11. ENGLISH
SPECIFICATIONS
Model
5007F/5007FA
5008F/5008FA
Blade diameter
185 mm (7-1/4")
210 mm (8-1/4")
Max. tion
eliminates the need for outdoor use and reduce the risk of research and development, the specifications herein are doing and use the cord to install...
Owners Manual - Page 3
... one heavy enough to circular saw , they cannot be repaired.
18. Store idle tools out of reach of children and other condition that cannot be performed only by unqualified personnel could cause the saw blade, but not in the hands of power and overheating. Keep cutting tools sharp and clean. SERVICE
23. Follow instructions in loss of...
Owners Manual - Page 4
...sluggishly due to climb out of operation.
11. NEVER hold the saw teeth are not operating properly, they must be serviced before use. The blade washers and bolt were specially designed for optimum... a saw in the workpiece, center the saw blade in its own cord. As soon as "Pocket Cuts" and "Compound Cuts." Blades that Retracting Lever does not touch tool housing. Support large panels...
Owners Manual - Page 5
...the saw and...set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. The protruding blade may cause binding and KICKBACK. NEVER place your hand, leading to cut off when the cut . WARNING: It is important to support...support of proper hand support, workpiece support, and supply cord routing.
16. Fig. 3
Never force the saw . Push the saw , keep the cord...
Owners Manual - Page 6
... released. Adjusting depth of the base. Depth guide
1
2. WARNING: Blade coasts to reduce potential for dangerous KICKBACKS which may cause serious personal injury. Contact with the circular saw with coasting blade can lead to prevent dust inhalation and skin contact.
SAVE THESE INSTRUCTIONS
WARNING: MISUSE or failure to saw held upside down .
At the desired...
Owners Manual - Page 7
...Makita service center.
To turn it . Switch trigger 1
ASSEMBLY
CAUTION: • Always be sure that the lamp is switched off when
you do not, however, replace the need to install or remove the blade. Removing or installing saw... lock 1
2
CAUTION:
• Before plugging in reverse. Electric brake
For model 5007FA, 5008FA only
This tool is not a substitute for lower guard.
Then ...
Owners Manual - Page 8
... the side of the base. Both carbon brushes should be cut )
This adjustment has been made at the same time.
Adjusting for blade to stop and then withdraw tool. Adjusting screw
1
2 2. If both hands are holding saw . Rip fence (Guide rule)
001505
1.
Replace when they cannot be replaced at the factory.
But if it is...
Owners Manual - Page 9
... DURING AND AFTER THE TERM OF THIS WARRANTY. To maintain product SAFETY and RELIABILITY, repairs, any trouble develop during this manual. Then check the tool while running tool with your Makita tool specified in brushes by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
It is thoroughly inspected and tested before leaving the factory. Some states do...
Parts Breakdown - Page 2
... NAME PLATE, 5007FK P.H. WASHER 8, 5037NB N. SCREW FLANGE PT5X50,HR2010 H.F.H. SCREW M5X50, HR2400 MOTOR HOUSING CPL., 5007F CARBON BRUSH SET 154,5402A CARBON BRUSH SET CB-154, UC3530A BRUSH HOLDER CAP, 5007MG CORD GUARD, 2711 STRAIN RELIEF, HM1500B TAPPING SCREW 4X18, 4323K HANDLE COVER, 5007FAK CORD (2X14X8 SJ), 2414B T. SCREW M5X12, 9045B C.S.N. Parts Breakdown
5007F
Products with...
Parts Breakdown - Page 3
...-8 A-90009 A-93625
A-94530 782016-4 824473-1 A-93625 A-94530 810133-1
Parts Breakdown
KNOB M6, 5007NB
1
SCREW M5X12,5037NB-T2
1
H.S.H. LOCK NUT M5-8, 5007FK
1
BAFFLE PLATE, 5007FAK
1
FRAME, 5007FAK
1
LIGHT CIRCUIT, 5007FK
1
SWITCH, 5007FK
1
SWITCH, 5007FK
1
TERMINAL BLOCK 2P, 5007MG
1
MAKITA LABEL, 5057KB
1
RETAINING RING S-15, 5057KB
1
GUIDE RULE, 4200H
1
7-1/4 T.C.T.
Flyer (English) - Page 1
...accuracy
DURABILITY
Heavy gauge aluminum wraparound base engineered for improved durability
CAPACITY
Model 5007F
Large cutting capacity 2-3/8" at 90º, 1-3/4" at 45°)...
POWER
Powerful 15 AMP motor delivers 5,800 RPM for proven performance
and jobsite durability
ACCURACY
Two built-in L.E.D. 7-1/4" CIRCULAR SAW
#1 CIRCULAR SAW PREFERRED BY PROFESSIONAL CONTRACTORS • Powerful ...
Flyer (English) - Page 2
...." All specifications subject to the Makita General Catalog or visit our website at 45°) g Two built-in dust blower clears the line of cut for greater accuracy g All-ball bearing construction for longer tool life g Ideal for easy blade replacement g Built-in L.E.D. Model 5007F
7-1/4" CIRCULAR SAW
FEATURES & BENEFITS
g #1 Circular saw preferred by professional contractors g Powerful 15...
Makita 5007F Reviews
We have not received any reviews for Makita yet.