Makita GA7082 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita GA7082 manuals!
Problems with Makita GA7082?
Ask a Question
Free Makita GA7082 manuals!
Problems with Makita GA7082?
Ask a Question
Popular Makita GA7082 Manual Pages
Instruction Manual - Page 2
...instructions)
SPECIFICATIONS
Model:
GA7080 GA7081 GA7082 GA9080 GA9081 GA9082
Wheel diameter
180 mm (7″)
230 mm (9″)
Max.
Cluttered or
dark areas invite accidents. 2. spheres, such as in the presence of drugs, alcohol or medication. Distractions can cause you install... area safety 1. There is damaged, have it replaced by the manufacturer or his agent in explosive atmo...
Instruction Manual - Page 3
...ft.
18 18 16 14
Total length of tools allow you to install the proper outlet. Do not overreach. Dress properly. Do not let... tool serviced by a qualified repair person using the tool, do not allow persons unfamiliar with these instructions, taking...length and nameplate ampere rating. When using only identical replacement parts. A power source with voltage less than the other ...
Instruction Manual - Page 5
...stop. Observe the instructions of the manufacturer for... to these parts could result ...Specific for Grinding and Abrasive Cutting-Off Operations:
1. Damage to adapt large hole abrasive wheels.
12. Wheels for which the power tool was not designed cannot be sure to use undamaged wheel flanges that could indicate poor installation... spindle length.
14. Supports must be extremely hot ...
Instruction Manual - Page 6
...instruction manual may enter the tool, which causes tool breakage.
21. If working place is switched off and unplugged before operation. Make sure there are no electrical cables, water pipes, gas pipes etc. that the tool is extremely hot and humid, or badly polluted by conductive dust, use ) replace...30 mA) to prevent spindle rotation when installing or removing accessories.
1
Fig.1 ►...
Instruction Manual - Page 7
... locking tool in "ON" position for model GA7080 / GA7081 / GA9080 / GA9081
1
Fig.4 ► 1 .
Switch trigger 2. For tool with the lock-off switch
Country specific
CAUTION: Switch can be locked in "... the tool is provided. For tool with the lock-on and lock-off switch
Country specific (including Australia and New Zealand) To prevent the switch trigger from accidentally pulled, a ...
Instruction Manual - Page 8
... cuts live wire unexpectedly.
1
Fig.6
2
3
► 1 . Touching the metal part may result in the figure. WARNING: When using a depressed center wheel, flap disc, flex wheel...3. Installing side grip (handle)
CAUTION: Always be more comfortable than the original side grip for model GA7080 / GA7081 / GA9080 / GA9081 Soft start feature reduces starting reaction. Gripping area
Installing or...
Instruction Manual - Page 10
... pad 4. Lock nut wrench 2. Wheel can be also used. Inner
flange
Follow instructions for use with the lock nut wrench.
Abrasive disc 3. Mount the inner flange ...and securely tighten clockwise.
1
Installing or removing abrasive disc
Optional accessory
1
2 3
2 Fig.13 ► 1 . Fit the wheel / disc on accessories page in this manual. Installing or removing abrasive cutoff / ...
Instruction Manual - Page 11
... . Dust collecting wheel guard 6. Wire wheel brush
Remove any accessories on spindle. Installing dust collecting wheel guard
Dust collecting wheel guard for grinding (for use in grinding ...flat concrete with broken wires. Bearing box
WARNING: Dust collecting wheel guard for grinding is only for model GA7080 / GA7081 / GA9080 / GA9081)
1
3
2
4
Fig.18 ► 1 . Wheel ...
Instruction Manual - Page 12
... wheel breakage. WARNING: ALWAYS replace wheel if tool is in both... one hand on housing and the other saw blades. Refer to the instruction manual attached to operator.
CAUTION: Never switch on the side grip (handle).... of the wheel has been rounded off (for model GA9080 / GA9081 / GA9082)
Fig.21 NOTE: For information how to install the dust collecting cover, refer to personal injury...
Instruction Manual - Page 13
...cup brush
Optional accessory CAUTION: Check operation of the wheel in front of the wheel. For model GA7080 and GA9080, you can rotate the switch handle. NOTICE: Avoid applying too much pressure ...
Fig.24
Usage example: operation with abrasive cut -off wheel with GA7081 / GA7082 / GA9081 / GA9082
Usage example: operation with diamond wheel with GA7080 / GA9080
Fig.26 Usage example:...
Instruction Manual - Page 14
... brush
Optional accessory
CAUTION: Check operation of wire wheel brush by Makita Authorized or Factory Service Centers, always using wire wheel brush. NOTICE: Avoid applying too much pressure which causes over bending of wires when using Makita replacement parts.
Inhalation vent
Fig.29
MAINTENANCE
CAUTION: Always be kept clean. To maintain product SAFETY...
Instruction Manual - Page 15
...included depending on the country)
Wire cup brush
-
Only use accessory or attachment for use of injury to persons.
The use with your local Makita Service Center.
1
2
6
6
2
3
3
7
3
4
8
8
10
5
5
9 5
11 5
12
2
16
18
22
13 14..., ask your Makita tool specified in this manual. Diamond wheel
Dust collecting wheel guard for dust collecting wheel guard
- Side...
Instruction Manual - Page 16
... Other countries: www.makita.com
16 ENGLISH Dust cover attachment
NOTE: *1 Use only the wheel guard which is not available, refer to the warranty details set forth at below website for the most current warranty terms applicable to the annexed warranty sheet for your respective country.
NOTE: *2 In countries other than...
Parts Breakdown - Page 2
...
O RING 6
1
PAN HEAD SCREW M8X25
1
INNER FLANGE 89
1
LOCK NUT 5/8-45
1
DIFFUSER
1
HEX. Model GA7082 Parts List
Item#
Part#
001-1
922253-0
002
413H41-9
003
233292-8
004
136698-8
004 C10 262118-7
004 C20 263002-9
004 D10
005
...
1
CAUTION LABEL
1
BRUSH HOLDER COVER R
1
TAPPING SCREW 4X14
1
CARBON BRUSH SET CB-224 (191T31-1) 1
BRUSH HOLDER
2
TAPPING SCREW 4X14
2
Parts Breakdown - Page 3
LABEL
1
056
811S57-8 GA7082 NAME PLATE
1
A01
143486-6
GRIP 37 COMPLETE
1
A02
782412-6
LOCK NUT WRENCH 28
1 039
251489-7
TAPPING SCREW 5X30
4
043
456245-2
BRUSH HOLDER COVER L
1
046
266385-6
TAPPING SCREW 4X14
1
047
183C63-0 HANDLE SET
1
047 D10
INC. 52
048
266326-2
TAPPING SCREW 4X18
2
049
266385-6
TAPPING SCREW 4X14
1
050
687169-3
STRAIN...
Makita GA7082 Reviews
We have not received any reviews for Makita yet.