Makita XAD05T Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita XAD05T manuals!
Problems with Makita XAD05T?
Ask a Question
Free Makita XAD05T manuals!
Problems with Makita XAD05T?
Ask a Question
Popular Makita XAD05T Manual Pages
XAD05 XAD06 Instruction Manual - Page 2
...instructions, illustrations and specifications provided with earthed (grounded) power tools. Failure to EPTA-Procedure 01/2014, are subject to change without notice.
• Specifications may differ from heat, oil, sharp edges or moving parts... flammable liquids, gases or dust. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Gear speed Drilling capacities
Steel Wood
XAD05
XAD06
High...
XAD05 XAD06 Instruction Manual - Page 3
...position before making any other persons in the moving parts, breakage of their device and/ or doctor ...the power tool or these instructions to control.
7. If contact accidentally occurs, flush with specifically designated battery packs. If liquid...the power tool repaired before turning the power tool on invites accidents.
4. A charger that cannot be repaired.
3. Keep ...
XAD05 XAD06 Instruction Manual - Page 4
...in this instruction manual may be performed by a qualified repair person using the tool in the instructions for battery...is below when using only identical replacement parts. At higher speeds, the bit...serviced by the manufacturer or authorized service providers.
3. Follow instruction for lubricating and changing accessories.
4. Keep hands away from repeated use and care. Never service...
XAD05 XAD06 Instruction Manual - Page 5
...is required.
CAUTION: Hold the tool and the battery cartridge firmly when installing or removing battery cartridge. Battery cartridge
To remove the battery cartridge, slide... Overcharging shortens the battery service life.
3.
If the cartridge does not slide in the packaging.
11. Pay attention to the Dangerous Goods Legislation requirements. Unless the tool supports the use it is ...
XAD05 XAD06 Instruction Manual - Page 6
Switch action
2
CAUTION: Before installing the battery cartridge into
the tool, always check to see the source of light directly. NOTE: Depending on the battery cartridge to 25%
Charge the ...
XAD05 XAD06 Instruction Manual - Page 7
... scratch the lens of rotation. Reversing switch lever
Installing key holder
(Country specific)
Speed change
NOTICE: Use the speed change knob... that the key holder is released, have the tool serviced at a Makita service center. Changing the tool speed before operation.
Screw ...pointer points to the low speed mode.
NOTICE: Always set the reversing switch lever to wipe the dirt off in...
XAD05 XAD06 Instruction Manual - Page 8
...simply lift up hook until it will go .
Then release the sleeve to the instructions above. Sleeve
NOTE: If the drill bit is convenient for temporarily hanging the tool...inserting the drill bit, make sure that it snaps into the open position.
Drill bit 2. Installing or removing drill bit
For model XAD05
To install the drill bit, place it in the chuck as far as it snaps into the closed ...
XAD05 XAD06 Instruction Manual - Page 9
...of the button, it fully until it is important that the hook is a powerful tool. The guide screw makes drilling easier by pulling the drill bit into the workpiece.
Insert it is not locked.... Before use, always check for connecting the lanyard (tether strap). CAUTION: Do not install or remove any accessory while hanging the tool. High torque is also used for damages,...
XAD05 XAD06 Instruction Manual - Page 10
...set forth at height". Do not use single action spring clip carabineers. 16. Do not carry the tool by Makita Authorized or Factory Service Centers, always using Makita replacement parts...bit begins to follow the warnings and instructions may result in the list may ...type carabineers. Lanyard (tether strap) connection
Safety warnings specific for lanyard (tether strap) must be
tagged and ...
Parts Breakdown - Page 2
Model XAD05T/Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
183S72-5
001 D10
002
413433-4
003
911243-8
...-5
043
227877-0
044
253493-2
045
413438-4
046
911063-0
047
127066-6
047 C10 232518-5
051
127282-0
COVER SET INC. 18 FRONT HANDLE PAN HEAD SCREW M5X25 TAPPING SCREW 4X18 GEAR HOUSING BALL BEARING 608ZZ HEX. NUT M14 ...
Parts Breakdown - Page 3
... KEY S13 BATTERY COVER DC18RC FAST CHARGER COMPO-PARTS BATTERY BL1850B SET (197283-2) HOOK ASSEMBLY PAN HEAD SCREW M5X12 TOOL BAG
1 PC. 1 1 PC. 0 6 PC. 1 PC. 1 PC. 1 0 1 1 1 PC. 0 9 PC. 1 2 PC. 1 PC. 0 2 PC. 1 PC. 1 PC. 1 PC. 1 1 PC. 1 1 2 PC. 1 PC. 0 1 1 PC. 1 1 2 PC. (XAD05T) 1 PC. (XAD05T) 0 2 PC. (XAD05T) 1 2 PC. 1 PC. (XAD05T) LABEL HANDLE SET RUBBER PIN 6 HEX. LOCK NUT M4-7 INC...
Makita XAD05T Reviews
Do you have an experience with the Makita XAD05T that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!