Makita XBP03Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XBP03Z manuals!
Problems with Makita XBP03Z?
Ask a Question
Free Makita XBP03Z manuals!
Problems with Makita XBP03Z?
Ask a Question
Popular Makita XBP03Z Manual Pages
XBP03 Instruction Manual - Page 2
... which may differ from heat, oil, sharp edges or moving parts.
Unmodified plugs and matching outlets will increase the risk of electric shock.
2. Water entering a power tool will reduce risk of electric shock.
4. ENGLISH (Original instructions)
SPECIFICATIONS
Model:
XBP03
Max.
Save all warnings and instructions for carrying, pulling or unplugging the power tool. Work area...
XBP03 Instruction Manual - Page 3
...second.
9. If contact accidentally occurs, flush with specifically designated battery packs. Liquid ejected from oil and ...
2. When using power tools.The goggles must be repaired.
3. avoid contact. Do not use . Damaged or...parts, breakage of battery pack may exhibit unpredictable behaviour resulting in unexpected situations.
9. Recharge only with the power tool or these instructions...
XBP03 Instruction Manual - Page 4
... firmly before cutting.
5. Never service damaged battery packs. Hold power tool by Makita. Wipe off all instructions and cautionary markings on packaging and labeling must be cautious of the item being shipped, consulting an expert for the Makita tool and charger.
4 ENGLISH diately after operation; The battery cartridge can explode in "SPECIFICATIONS".
3. Please also observe...
XBP03 Instruction Manual - Page 5
... .
4. Overcharging shortens the battery service life.
3. If the cartridge does not slide in easily, it locks in damage to extend tool and battery life. Indicating the remaining battery capacity
Only for a long period (more than six months). Indicator lamps 2. CAUTION: Do not install the battery cartridge forcibly.
Installing or removing battery cartridge
CAUTION...
XBP03 Instruction Manual - Page 6
...charge the battery. After use, press in the light or see that the tool is removed before installing the band saw blade.
NOTE: Do not apply impact to the lamp, which may lower the ...A side and pull the switch trigger.
Release the switch trigger to it may cause damage or shorted service time to stop the application that causes it to slip or come off the lens of light directly...
XBP03 Instruction Manual - Page 7
... the installation procedure in place and turn the blade-tightening lever counterclockwise until it stops. Open the wheel cover. 2. This places proper tension on the wheels. 4.
After sliding the stopper plate, secure it to the A side fully. Lower holder 2. Wheel 2. Position the band saw blade.
9. Stopper plate 2. 1
2
3
5. With pressing the middle part...
XBP03 Instruction Manual - Page 8
...causing injury to the suitable cutting position on the workpiece as illustrated.
To install the hook, set the hook alongside the groove and tighten it locks in personal injury. ... tool as illustrated.
1 2
► 1 .
Otherwise the tool may result in the cut.
1.
Installing hook
Optional accessory
CAUTION: Do not use the hook for hanging the tool. Hands may cause the hook...
XBP03 Instruction Manual - Page 9
...: When not using the tool for a long period of the band saw blade does not slip out. CAUTION: When cutting cast iron, do not use Makita cutting wax as illustrated.
1 ► 1 . Gently lower the blade into the cutting wax as a cutting lubricant. As you reach the end of the tool or...
XBP03 Instruction Manual - Page 10
... or Factory Service Centers, always using Makita replacement parts. Cleaning
CAUTION: Wax and chips on the rubber tires on the wheel and the band saw blade to slip and come off and the battery cartridge is not available, refer to persons. If annexed warranty sheet is removed before attempting to this manual. NOTICE: Never use...
XBP03 Parts Breakdown - Page 2
... HEAD BOLT M5X20 URETHANE RING 4 FUSE UNIT TAPPING SCREW CT 4X16 HANDLE SET HEX. LOCKING NUT M4-7 RUBBER PIN 6 INC. 24 SWITCH TG73BDS-1 LOCK OFF BUTTON SWITCH LEVER XBP03 SERIAL NO. Model XBP03 T/Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
187711-5
001 D10
002
266326-2
003
266034-5
004...
XBP03 Parts Breakdown - Page 4
095
266034-5
098
161427-0
A01
783202-0
A02
B-40559
A03
***DC18RC
A03 D10
A04
BL1850B
A05
450128-8
A06
831303-9
TAPPING SCREW CT 4X16 HOOK HEX. WRENCH 4 PORTABLE BANDSAW BLADE 18TPI DC18RC FAST CHARGER COMPO-PARTS BATTERY BL1850B SET (197283-2) BATTERY COVER TOOL BAG
3 PC. 2 PC. 1 PC. 1 PC. 1 PC. (XBP03T) 0 2 PC. (XBP03T) 2 PC. (XBP03T) 1 PC. (XBP03T)
XBP03Z New Tool Flyers English - Page 1
... Speed (ft./min 630 ft./min. Blade Length 32-7/8" Battery 18V LXT® Lithium-Ion Overall Length 18-3/4" Net Weight (with battery 9 lbs. blade speed for accurate cutting
SPECIFICATIONS
Max. All models and accessories subject to change lever for fast installation and removal
of Makita Corporation and is ideal for cutting conduit, Unistrut®, copper pipe...
Makita XBP03Z Reviews
We have not received any reviews for Makita yet.