Makita XDG01Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XDG01Z manuals!
Problems with Makita XDG01Z?
Ask a Question
Free Makita XDG01Z manuals!
Problems with Makita XDG01Z?
Ask a Question
Popular Makita XDG01Z Manual Pages
XDG01Z Instruction Manual - Page 2
...
GEA006-2
General Power Tool Safety Warnings
WARNING Read all safety warnings and all warnings and instructions for future reference. ENGLISH (Original instructions)
SPECIFICATIONS
Model
XDG01
Max. If operating a power tool in any adjusting key or wrench before connecting to a rotating part of electric shock.
8.
Do not operate power tools in explosive
atmospheres, such as dust...
XDG01Z Instruction Manual - Page 3
... performed. Properly maintained cutting tools with the power tool or these instructions, taking into account the working conditions and the work to the maximum speed marked on and off are not specifically designed and recommended by a qualified
repair person using only identical replacement parts. Battery tool use and care 17. A charger that may affect the...
XDG01Z Instruction Manual - Page 4
...Kickback is the same direction as abrasive wheels for damage or install an undamaged accessory. d) Always feed the bit into the...the bits or making any adjustments, make exposed metal parts of your body and arm to allow you to ... loss.
10. Wear personal protective equipment. Prolonged exposure to support workpiece whenever practical. Keep bystanders a safe distance away from ...
XDG01Z Instruction Manual - Page 5
... to safety rules for use ) replace strict adherence to disposal of your eyes...instruction manual may be sure you and other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to follow the safety rules stated in a risk of the wheel to drop or strike battery. 9. Be careful not to perform the grinding. 24. SAVE THESE INSTRUCTIONS.
5 Safety Warnings Specific...
XDG01Z Instruction Manual - Page 6
...shortens the battery service life. 3. Charge the battery cartridge once in every six months if you . • Do not install the battery cartridge forcibly. To install the battery ...tool and battery cartridge and a personal injury. Never recharge a fully charged battery cartridge. Installing or removing battery cartridge
1
1.
Button 2. Failure to hold the tool and the battery...
XDG01Z Instruction Manual - Page 7
...CAUTION: • Before installing the battery cartridge into..." position and maintain firm grasp on tool. This prevents the motor and its related parts from being damaged.
− In this case, to start the tool again, move...)" position once and then to the "I (ON)" position.
− Battery cartridge replacing signal − When the remaining battery capacity gets low, the indicator lamp lights up...
XDG01Z Instruction Manual - Page 8
...or the like. Wheel point 3. Use one wrench to hold the spindle and the other one to install a 1/8" shank wheel point. reaches maximum speed.
Discoloration, deformation or cracks may result. Use an optional...the top end of the motor. To obtain a good finish, move the tool in the holders. Replace when they wear down to the workpiece gently. Collet nut 4. Wrench 13
1
2 3
4
011468
...
XDG01Z Instruction Manual - Page 9
... "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY.
Then tighten the handle firmly by others: repairs are
recommended for use with your local Makita Service Center.
Some states do not allow the exclusion or limitation of the rubber is caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Should any other...
XDG01Z Parts Breakdown - Page 2
Model XDG01Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
001
424380-4
002
763668-0
003
763673-7
004
317999-5
005
443124-3
...RING 13 LED CIRCUIT YOKE UNIT ENDBELL COMPLETE XDG01 NAME PLATE TAPPING SCREW 4X18 SWITCH KNOB HOUSING SET RUBBER PIN 6 INC. 29 SWITCH LEVER SWITCH 1246.3223 CONTROLLER TERMINAL HOUSING SET RUBBER PIN 6 INC. 24 CARBON BRUSH ...
Makita XDG01Z Reviews
We have not received any reviews for Makita yet.