Makita XST01Z Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita XST01Z manuals!
Problems with Makita XST01Z?
Ask a Question
Free Makita XST01Z manuals!
Problems with Makita XST01Z?
Ask a Question
Popular Makita XST01Z Manual Pages
Makita XST01 Instruction Manual - Page 1
IMPORTANTE: Leer antes de usar. 1 IMPORTANT: Lire avant usage. INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES
Cordless Oil-Pulse Driver Visseuse Oléopneumatique Sans-Fil Atornillador Inalámbrico de Impulso Hidráulico
XST01
015149
IMPORTANT: Read Before Using.
Makita XST01 Instruction Manual - Page 2
ENGLISH (Original instructions)
SPECIFICATIONS
Model
XST01
Capacities
Machine screw Standard bolt
4 mm - 8 mm (5/32" - 5/16") 5 mm - 8 mm (3/16" - 5/16")...under the influence of inattention while operating power tools may differ from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
Never use a power tool while you ...
Makita XST01 Instruction Manual - Page 3
... using only identical replacement parts. Fasteners contacting a "live " and could burn your application. Be sure no one terminal to operate the power tool. They may be sure you have the power tool repaired before connecting to a rotating part of the power tool may create a risk of untrained users. 21. SAVE THESE INSTRUCTIONS.
3 Remove any other...
Makita XST01 Instruction Manual - Page 4
... may result in
this instruction manual may cause serious personal
...it . 4. Do not use ) replace strict adherence
to
disposal of time.
...service life. 3. Do not short the battery cartridge: (1) Do not touch the terminals with any
conductive material. (2) Avoid storing battery cartridge in loss of blow
IMPORTANT SAFETY INSTRUCTIONS
ENC007-8
FOR BATTERY CARTRIDGE
1. SAVE THESE INSTRUCTIONS...
Makita XST01 Instruction Manual - Page 5
... is not locked completely.
NOTE: • The tool automatically stops if you . • Do not install the battery cartridge forcibly. FUNCTIONAL DESCRIPTION
1.
Battery cartridge
3
014963
CAUTION: • Always switch off , ... trigger is released, have the tool serviced at a Makita service center. The lamp goes out approximately 10 seconds after the switch trigger is pulled.
5
Makita XST01 Instruction Manual - Page 6
...tool. • When not operating the tool, always set screws. 3. Characteristics of Cordless Oil-impulse Driver
The Makita Cordless Oil-impulse Driver is OFF.
2
• While pulling the switch ...check the direction of tool due to a complete stop. Avoid using oil viscosity to set the reversing switch lever to change the direction of rotation. Changed in the neutral position...
Makita XST01 Instruction Manual - Page 7
... screw head. Soft
1,400 (/min)
Tightening when excessive tightening need to the work. In this mode, the tool starts to prevent the damages on the parts during heavy load operation with the self-drilling -screw tip. Medium
2,200 (/min)
Tightening when a good finishing is needed . Tightening in underwork material / Tightening long...
Makita XST01 Instruction Manual - Page 8
... high current, the tool automatically stops without any work on the tool. To install the bit, insert the bit into the
sleeve, the sleeve will automatically stop ...power to the motor to the instructions above.
8 Battery capacity
Overheat protection for tool
When the tool is operated in the direction of the following state. Bit 2. Installing or removing driver bit or socket bit
20%...
Makita XST01 Instruction Manual - Page 9
...the tool on the switch trigger so that it comes out, do so may be installed on the side of the workpiece to determine the proper fastening time for temporarily hanging the...torque
Fastening torque
2 3
014996
The hook is shown in the figures, the screw or the point of the driver bit may cause the tool excessive heat and damage.
0
1.0
2.0
Fastening time (S)
015301
Hold the tool ...
Makita XST01 Instruction Manual - Page 10
... fastening torque. Should any other maintenance or adjustment should be reduced. 2. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at low speed will be performed by Makita Authorized Service Centers, always using Makita replacement parts. Some states do not allow limitation on how long an implied warranty lasts, so the...
Makita XST01Z Parts Breakdown - Page 2
... 2X10
021
620354-5 CONTROLLER
022
687464-1 SUPPORT
023
629137-0 STATOR
024
619358-2 ROTOR
026
643860-3 TERMINAL
027
620355-3 LED CIRCUIT
028
187989-0 HOUSING SET
028 C10 263005-3 RUBBER PIN 6
028 C20 252126-6 HEX. Model XST01Z Pats List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
187989-0 HOUSING SET
001 C10 263005-3 RUBBER PIN...
Makita XST01Z/XST01M New Tool Flyer English - Page 1
18V LXT® Lithium-Ion Oil-Impulse Brushless Cordless 3-Speed Impact Driver Kit
Models XST01M/ XST01Z
Up to 30% Lower Noise for Quiet Operation
INNOVATION
Oil-Impulse™ Technology utilizes oil to hydraulically drive the impact mechanism for lower noise
CONTROL
Quick-Shift Mode™ with battery) UPC Code XST01M UPC Code XST01Z
1/4" 0 - 2,700 / 0 - 2,200 / 0 - 1,400 IPM 0 - 3,200 / 0 ...
Makita XST01Z Reviews
Do you have an experience with the Makita XST01Z that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!