Milwaukee Tool M18 FUEL 1-9/16" SDS Max Hammer Drill Tool Only Support and Manuals
Get Help and Manuals for this Milwaukee Tool item
View All Support Options Below
Free Milwaukee Tool M18 FUEL 1-9/16" SDS Max Hammer Drill Tool Only manuals!
Problems with Milwaukee Tool M18 FUEL 1-9/16" SDS Max Hammer Drill Tool Only?
Ask a Question
Free Milwaukee Tool M18 FUEL 1-9/16" SDS Max Hammer Drill Tool Only manuals!
Problems with Milwaukee Tool M18 FUEL 1-9/16" SDS Max Hammer Drill Tool Only?
Ask a Question
Popular Milwaukee Tool M18 FUEL 1-9/16" SDS Max Hammer Drill Tool Only Manual Pages
Operators Manual - Page 2
... and refrigerators. A charger that cannot be repaired. •Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from moving parts, breakage of fire when used with another battery pack. •Use power tools only with specifically designated battery packs.
ated (cordless) power tool.
•If devices are caused by...
Operators Manual - Page 3
... or modified.
If in doubt,
consult a structural engineer. contact Milwaukee Tool or a trained
professional for a free
replacement.
•
WARNING
Some dust created by a qualified repair person using long drill bits
•Always start drilling at temperatures outside the temperature range specified in the instructions. These carry
important information. Some examples of these...
Operators Manual - Page 4
... These MILWAUKEE Rotary Hammers have three settings: hammering with rotation. With a chisel mounted in relation to the desired position. 3.
cific charging instructions, read the operator's
manual supplied with drill bits. 2.
Hammering only. When the pressure on the bit is released. 2. Starting and Stopping 1. To reduce the risk of the tool. 3. sories specifically...
Operators Manual - Page 5
.... If the bit should bind, a built-in forward to drop off when drilling large or deep holes, pull the bit partially out of slab
evacuated more easily.
6. Repeat until the tool starts hammering. Insert the center pin and guide plate assembly into the tool. 2. Start the cut slowly. Insert and lock a bit or chisel into...
Operators Manual - Page 6
... the
1/8"
concrete.
3. See "Installing Bits and Chisels".
2.
Clean
the dust and cuttings
from the cut . Snap the head off several times
while drilling the hole.
4. Chiseling and Chipping
MILWAUKEE Rotary Hammers may be used for chipping and chiseling. Bushing Tools Used to clean dust
and cuttings from the anchor.
rotation" setting to set
and the tooth anchor...
Operators Manual - Page 7
... cleaning solvents, ammonia and household detergents containing ammonia. Never use accessories specifically recom- Return of the power tool to achieve best performance. Normal Wear: Many power tools need periodic parts replacement and service to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is warranted to the original...
Service Parts List - Page 1
... instructions, torques chart, maintenance instructions and service kits.
• See Page 4 for wiring instructions. Right
(1)
46c 06-82-2025 M3.5 x 16mm Pan Hd. ST T-20 Screw
(9)
49b Housing Halve - MILWAUKEE ELECTRIC TOOL CORPORATION 13135 W. AND SERIAL NO. Right (Cover)
(1)
49c Housing Halve - WHEN ORDERING PARTS REVISED BULLETIN DATE
M18™ FUEL™ 5Kg SDS-Max Rotary Hammer...
Service Parts List - Page 2
...12
position prior to installing in gear case cavity. REQ. (1) (1) (1) (1) (2) (1)
(6)
(1) (1) (1)
SERVICE FIXTURES FOR THE 2717-20 and 5317-20 SDS ROTARY HAMMER
PART NO. DO NOT exceed... O-Ring 16 44-20-5316 Key
17 38-50-5316 SDS-Max Spindle Assembly
17a 44-82-5317 SDS-Max Spindle
17b 43-...Driver
(1)
61-10-1032 Seal Expander
(2)
61-10-1035 Anvil Insertion Guide
(2)
61-10-1037 Seal...
Service Parts List - Page 3
...installing... SERVICE ...MILWAUKEE Rotary Hammer...Hammer include lubrication replacement, and replacement of grease to gears and mechanism parts. Pack the rear of grease in the barrel. Place 18 grams of 'Q2' grease inside of the spindle driver prior to be no lubrication on barrel #17h
Coat the inside barrel.
3
3.
NO. 22a 22b 29a 29b 46c 47 49a
FASTENER TORQUE SPECIFICATIONS...
Service Parts List - Page 4
BE CAREFUL AND AVOID PINCHING WIRES BETWEEN HANDLE HALVES WHEN ASSEMBLING. LED PCBA Locking Shuttle
O-Ring (Both sides) On-Off Switch Fuel Logo Plate
= WIRE TRAPS or GUIDES
Terminal Block
AS AN AID TO REASSEMBLY, TAKE NOTICE OF WIRE ROUTING AND POSITION IN WIRE GUIDES AND TRAPS WHILE DISMANTLING TOOL.
Milwaukee Tool M18 FUEL 1-9/16" SDS Max Hammer Drill Tool Only Reviews
We have not received any reviews for Milwaukee Tool yet.