Owner's Manual
Page 76
... can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. models, and Celsius temperature in the front bumper. For more information, see page 97 ) . The temperature reading can adjust the outside Fahrenheit temperature in U.S. When you start your vehicle speed is displayed. ...The engine oil life is reset. Engine Oil Life Instruments and Controls ENGINE OIL LIFE This shows the outside temperature display (see page 439 . 73 2010 RL Multi-Information Display Outside Temperature OUTSIDE TEMPERATURE U.S.
... can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. models, and Celsius temperature in the front bumper. For more information, see page 97 ) . The temperature reading can adjust the outside Fahrenheit temperature in U.S. When you start your vehicle speed is displayed. ...The engine oil life is reset. Engine Oil Life Instruments and Controls ENGINE OIL LIFE This shows the outside temperature display (see page 439 . 73 2010 RL Multi-Information Display Outside Temperature OUTSIDE TEMPERATURE U.S.
Owner's Manual
Page 385
Slide the latch handle up the rest of the way. Lift the hood up most of the way and hold it up. If the hood latch handle moves stiffly, or if you can open the hood without lifting the handle, the mechanism should be cleaned and lubricated. 3. The hydraulic supports will lift it is securely latched. 382 2010 RL Make sure it up . Service Station Procedures LATCH 2. Reach between the hood and the front bumper with your finger. To close the hood, lower the hood to about a foot (30 cm) above the fender, then firmly press down on the front edge of the hood.
Slide the latch handle up the rest of the way. Lift the hood up most of the way and hold it up. If the hood latch handle moves stiffly, or if you can open the hood without lifting the handle, the mechanism should be cleaned and lubricated. 3. The hydraulic supports will lift it is securely latched. 382 2010 RL Make sure it up . Service Station Procedures LATCH 2. Reach between the hood and the front bumper with your finger. To close the hood, lower the hood to about a foot (30 cm) above the fender, then firmly press down on the front edge of the hood.
Owner's Manual
Page 470
Insert the new bulb into the bumper. 3. Push the electrical connector back onto the bulb. Remove the bulb by pushing on the side under cover into the hole, and turn it one-... from the bulb by turning it onequarter turn clockwise to lock it locks (the center is on the center until it in place. 6. Maintenance 467 2010 RL CLIP CONNECTOR BULB 1. Carefully push up the side under cover and tighten them securely. Make sure it is flush with a flat-tip screwdriver. 2. Put the...
Insert the new bulb into the bumper. 3. Push the electrical connector back onto the bulb. Remove the bulb by pushing on the side under cover into the hole, and turn it one-... from the bulb by turning it onequarter turn clockwise to lock it locks (the center is on the center until it in place. 6. Maintenance 467 2010 RL CLIP CONNECTOR BULB 1. Carefully push up the side under cover and tighten them securely. Make sure it is flush with a flat-tip screwdriver. 2. Put the...
Owner's Manual
Page 516
... is required. When you can use the towing hook: 1. Remove the cover from the front bumper by pushing the right corner edge of towing will load your vehicle on the back of the Unexpected CONTINUED 513 2010 RL Any other method of the cover with just a rope or chain. Emergency Towing, If Your...
... is required. When you can use the towing hook: 1. Remove the cover from the front bumper by pushing the right corner edge of towing will load your vehicle on the back of the Unexpected CONTINUED 513 2010 RL Any other method of the cover with just a rope or chain. Emergency Towing, If Your...
Owner's Manual
Page 517
If Your Vehicle Gets Stuck COVER WHEEL NUT WRENCH To avoid damage to tow the vehicle onto a f lat bed. Remove the towing hook and wheel nut wrench from the tool case in the spare tire. 3. Screw the towing hook into the hole, and tighten it as a tie down. Do not tow at an angle. The tow hook should not be used to your vehicle, use it with a tether. 2. Do not use the towing hook f or straight, f lat ground towing only. TETHER The cover is attached to the bumper with the wheel nut wrench. 514 2010 RL
If Your Vehicle Gets Stuck COVER WHEEL NUT WRENCH To avoid damage to tow the vehicle onto a f lat bed. Remove the towing hook and wheel nut wrench from the tool case in the spare tire. 3. Screw the towing hook into the hole, and tighten it as a tie down. Do not tow at an angle. The tow hook should not be used to your vehicle, use it with a tether. 2. Do not use the towing hook f or straight, f lat ground towing only. TETHER The cover is attached to the bumper with the wheel nut wrench. 514 2010 RL