User Guide
Page 94
...Pool on page 96. Note: To enable MaxIQ caching, read and write cache settings for "write-back" caching; Appendix C: Using the Adaptec RAID Configuration Utility ● 94 In the power management console, enter these details: Option Power Management Slow Down Drive After Power Off Drive ...as a read caching. 4 Press Tab. 5 Select the preferred MaxIQ setting (Enable/Disable), press Tab, then enable or disable MaxIQ. This is an optional setting. Note: Power Off Drive After duration should support low power mode. The regular time interval at which the system performs a health check...
...Pool on page 96. Note: To enable MaxIQ caching, read and write cache settings for "write-back" caching; Appendix C: Using the Adaptec RAID Configuration Utility ● 94 In the power management console, enter these details: Option Power Management Slow Down Drive After Power Off Drive ...as a read caching. 4 Press Tab. 5 Select the preferred MaxIQ setting (Enable/Disable), press Tab, then enable or disable MaxIQ. This is an optional setting. Note: Power Off Drive After duration should support low power mode. The regular time interval at which the system performs a health check...
User Guide
Page 98
...enabled, connected disk drives are displayed during a power failure. DVD/CD-ROM Boot Support When enabled, the system can be booted from a bootable CD. (This setting is enabled/disabled on all RAID controller models.) Alarm Control When enabled, the alarm sounds. When set to Fault...the disk drives adds a few seconds to Queuing (NCQ) attach more than 48 SATA II disk drives. Default is disabled. Appendix C: Using the Adaptec RAID Configuration Utility ● 98 General Controller Settings Note: Default settings are shown in systems that there may be rebuilt manually...
...enabled, connected disk drives are displayed during a power failure. DVD/CD-ROM Boot Support When enabled, the system can be booted from a bootable CD. (This setting is enabled/disabled on all RAID controller models.) Alarm Control When enabled, the alarm sounds. When set to Fault...the disk drives adds a few seconds to Queuing (NCQ) attach more than 48 SATA II disk drives. Default is disabled. Appendix C: Using the Adaptec RAID Configuration Utility ● 98 General Controller Settings Note: Default settings are shown in systems that there may be rebuilt manually...
User Guide
Page 99
... and Verifying Disk Drives You can set time zone. Set to No (disabled) only if the controller is 00:00 to 23:59. Note: Make sure the operating system driver supports power management. Note: Default settings are read-only and non-editable. Stay...controller and devices. Formatting destroys all the internal drives will spin up. Appendix C: Using the Adaptec RAID Configuration Utility ● 99 Power Management Settings Note: When power management is disabled, no related options will spin up. Option Description Power Management Settings When enabled, switches the ...
... and Verifying Disk Drives You can set time zone. Set to No (disabled) only if the controller is 00:00 to 23:59. Note: Make sure the operating system driver supports power management. Note: Default settings are read-only and non-editable. Stay...controller and devices. Formatting destroys all the internal drives will spin up. Appendix C: Using the Adaptec RAID Configuration Utility ● 99 Power Management Settings Note: When power management is disabled, no related options will spin up. Option Description Power Management Settings When enabled, switches the ...
User Guide
Page 110
..., the process resumes without any user intervention. The possible error messages returned by your RAID controller, additional possible values are as follows: ● Yes (default)-Enable the write cache. ● No-Disable the write cache. Code Description 0 ACU ran without changes-ACU exited with no errors... switches.) For example: WriteCache=Yes ACU Error Codes When the ACU detects an error, it displays the error code on the RAID levels supported by the ACU are listed in the background; specify Wait=No. For example: Wait=Yes Wait=No WriteCache Keyword The WriteCache ...
..., the process resumes without any user intervention. The possible error messages returned by your RAID controller, additional possible values are as follows: ● Yes (default)-Enable the write cache. ● No-Disable the write cache. Code Description 0 ACU ran without changes-ACU exited with no errors... switches.) For example: WriteCache=Yes ACU Error Codes When the ACU detects an error, it displays the error code on the RAID levels supported by the ACU are listed in the background; specify Wait=No. For example: Wait=Yes Wait=No WriteCache Keyword The WriteCache ...