User Manual
Page 3
User Guide (English) Introduction Box Contents Elevate 6; User Guide; For additional product support, visit alesis.com/support. Frequency 100 200 500 1K 3 (Hz) 2K 5K 10K 20K Specifications subject to change without notice. Technical Specifications Frequency Response... Trim Low-Frequency Driver High-Frequency Driver Low-Frequency Amplifier High-Frequency Amplifier Input Sensitivity Maximum Output Input Impedance Polarity Dimensions (width x depth x height) Weight (monitor only) 55 Hz - 30 kHz (+3 dB) 45 Hz - 35 KHz (-10 dB) 2.2 kHz +2 dB, 0 dB, -2 dB above 3 kHz +2 dB, 0 dB, -2 dB...
User Guide (English) Introduction Box Contents Elevate 6; User Guide; For additional product support, visit alesis.com/support. Frequency 100 200 500 1K 3 (Hz) 2K 5K 10K 20K Specifications subject to change without notice. Technical Specifications Frequency Response... Trim Low-Frequency Driver High-Frequency Driver Low-Frequency Amplifier High-Frequency Amplifier Input Sensitivity Maximum Output Input Impedance Polarity Dimensions (width x depth x height) Weight (monitor only) 55 Hz - 30 kHz (+3 dB) 45 Hz - 35 KHz (-10 dB) 2.2 kHz +2 dB, 0 dB, -2 dB above 3 kHz +2 dB, 0 dB, -2 dB...
User Manual
Page 4
... and that the drivers face you. The woofer and tweeter are vertically aligned and will provide the best performance when the monitors are parallel to resonate sympathetically at least 3 feet (approximately 1 meter) away from you cannot use speaker stands, try placing the...flat surfaces. Placing them at low frequencies and may create strong reflections from building up your studio and monitors in the "front" third of the room. If your desk. If possible, place your monitors 3-5 feet (1-1.5 meters) apart from each other and from the nearest wall and other sound-absorbent ...
... and that the drivers face you. The woofer and tweeter are vertically aligned and will provide the best performance when the monitors are parallel to resonate sympathetically at least 3 feet (approximately 1 meter) away from you cannot use speaker stands, try placing the...flat surfaces. Placing them at low frequencies and may create strong reflections from building up your studio and monitors in the "front" third of the room. If your desk. If possible, place your monitors 3-5 feet (1-1.5 meters) apart from each other and from the nearest wall and other sound-absorbent ...
User Manual
Page 5
...TS), the tip of the plug is positive/hot, the ring is negative/cold, and the sleeve is line-level. Acoustic Compensation Since studio monitors (including the Elevate 6) are set up where the room cannot be easily modified to have a flat frequency response, you hear at the "mixing position." In ...for bass energy, resulting in an anechoic chamber to various parts of the speaker act as possible at the mixing position. Important: When using two Elevate 6 monitors, make sure the Volume knob, HF Trim switch, and LF Trim switch are tested and tuned in bass that sounds too "dead" (not ...
...TS), the tip of the plug is positive/hot, the ring is negative/cold, and the sleeve is line-level. Acoustic Compensation Since studio monitors (including the Elevate 6) are set up where the room cannot be easily modified to have a flat frequency response, you hear at the "mixing position." In ...for bass energy, resulting in an anechoic chamber to various parts of the speaker act as possible at the mixing position. Important: When using two Elevate 6 monitors, make sure the Volume knob, HF Trim switch, and LF Trim switch are tested and tuned in bass that sounds too "dead" (not ...
User Manual
Page 6
... very-low- LF Trim: Use this switch. 9. Woofer: This driver outputs the audio signal's low frequencies. 1 3. If you are using two Elevate 6 monitors, make sure the Volume knob, HF Trim switch, and LF Trim switch are in the same position on both... monitors. 8. nothing is identical on both monitors. 1. Features Important: When using two Elevate 6 monitors, make sure this switch. 6 Power Switch: Use this switch to 4 determine the optimal setting for this knob's setting...
... very-low- LF Trim: Use this switch. 9. Woofer: This driver outputs the audio signal's low frequencies. 1 3. If you are using two Elevate 6 monitors, make sure the Volume knob, HF Trim switch, and LF Trim switch are in the same position on both... monitors. 8. nothing is identical on both monitors. 1. Features Important: When using two Elevate 6 monitors, make sure this switch. 6 Power Switch: Use this switch to 4 determine the optimal setting for this knob's setting...