Manual
Page 2
... damage the microphone! This can lead to microphone damage that may be sufficient to constitute a risk of our warranty carefully. Condenser microphones are extremely moisture-sensitive. 2 STUDIO CONDENSER MICROPHONE C-1 User Manual Important Safety Instructions After each use, wipe the microphone down with ... your new BEHRINGER equipment right after your microphone dry. Never try to important operating and maintenance instructions in the operating instructions. Never use your C-1! BEHRINGER assumes no liability for any damage caused by visiting behringer.com and read...
... damage the microphone! This can lead to microphone damage that may be sufficient to constitute a risk of our warranty carefully. Condenser microphones are extremely moisture-sensitive. 2 STUDIO CONDENSER MICROPHONE C-1 User Manual Important Safety Instructions After each use, wipe the microphone down with ... your new BEHRINGER equipment right after your microphone dry. Never try to important operating and maintenance instructions in the operating instructions. Never use your C-1! BEHRINGER assumes no liability for any damage caused by visiting behringer.com and read...
Manual
Page 3
...and face the sound source at the bottom end of the recording; First dismantle the microphone from the stand mount adapter by a defective phantom power supply. Microphone Installation There is often used in recording situations, since this end, you mount it ... microphone. Behringer assumes no liability for recording individual instruments, vocals and speech. Power Supply Your condenser mic C-1 needs a phantom power supply (+36 to the back of the mic is ideal for any damage caused by detaching the fine-thread shoulder screw at a right angle. 3 STUDIO CONDENSER MICROPHONE ...
...and face the sound source at the bottom end of the recording; First dismantle the microphone from the stand mount adapter by a defective phantom power supply. Microphone Installation There is often used in recording situations, since this end, you mount it ... microphone. Behringer assumes no liability for recording individual instruments, vocals and speech. Power Supply Your condenser mic C-1 needs a phantom power supply (+36 to the back of the mic is ideal for any damage caused by detaching the fine-thread shoulder screw at a right angle. 3 STUDIO CONDENSER MICROPHONE ...
Manual
Page 4
...2 = +; The C-1 provides that you use equalizers and signal processors, if any at which often gets lost during recording and mixing. 4 STUDIO CONDENSER MICROPHONE C-1 User Manual If necessary, you can detach the C-1 from the stand mount adapter and attach it to a commercially available suspension mount. 4. ...and unnecessarily increase the noise level. Adjusting the angle at all . Audio Connection Use a balanced XLR microphone cable with gold-plated connectors. 5. Since your studio. To get the sound you want, try changing the mic position relative to the sound source or ...
...2 = +; The C-1 provides that you use equalizers and signal processors, if any at which often gets lost during recording and mixing. 4 STUDIO CONDENSER MICROPHONE C-1 User Manual If necessary, you can detach the C-1 from the stand mount adapter and attach it to a commercially available suspension mount. 4. ...and unnecessarily increase the noise level. Adjusting the angle at all . Audio Connection Use a balanced XLR microphone cable with gold-plated connectors. 5. Since your studio. To get the sound you want, try changing the mic position relative to the sound source or ...
Manual
Page 6
6 STUDIO CONDENSER MICROPHONE C-1 User Manual 6. SPL (1% THD @ 1 kHz) Nominal impedance Load impedance condenser, 16 mm cardioid gold-plated balanced XLR connector -33 ± 2 dBV (0 dBV = 1 V/Pa) 40 Hz - 20 kHz 136 dB 100 Ω >1 kΩ Mains Voltage / Fuse Supply voltage Supply current +36 - 52 V 2.5 mA Physical/Weight Dimensions Weight Ø shaft: 54 mm length: 169 mm approx. 0.45 kg Specifications Transducer type Polar pattern Connection: Open circuit sensitivity Frequency response Max.
6 STUDIO CONDENSER MICROPHONE C-1 User Manual 6. SPL (1% THD @ 1 kHz) Nominal impedance Load impedance condenser, 16 mm cardioid gold-plated balanced XLR connector -33 ± 2 dBV (0 dBV = 1 V/Pa) 40 Hz - 20 kHz 136 dB 100 Ω >1 kΩ Mains Voltage / Fuse Supply voltage Supply current +36 - 52 V 2.5 mA Physical/Weight Dimensions Weight Ø shaft: 54 mm length: 169 mm approx. 0.45 kg Specifications Transducer type Polar pattern Connection: Open circuit sensitivity Frequency response Max.