Installation Instructions
Page 1
... Adjust MW Trouble Adjust Memory Screw PIR Noise *= Cut only if using the Memory Voltage Pins Microwave Noise Voltage Pins or 1 Day Motion Monitor features. To be connected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must.... Use the DS820 or DS835 for such installations. • Never install the detector in . It should be provided by Bosch Security Systems can void the user's authority to operate the equipment. 2.0 Installation Considerations NOTE: The DS950 is +32°F to +120°F (0°C to +49°C), indoor...
... Adjust MW Trouble Adjust Memory Screw PIR Noise *= Cut only if using the Memory Voltage Pins Microwave Noise Voltage Pins or 1 Day Motion Monitor features. To be connected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must.... Use the DS820 or DS835 for such installations. • Never install the detector in . It should be provided by Bosch Security Systems can void the user's authority to operate the equipment. 2.0 Installation Considerations NOTE: The DS950 is +32°F to +120°F (0°C to +49°C), indoor...
Installation Instructions
Page 2
...made . 5.0 LED Operation The chart below shows tri-color LEDs the detector uses to count down until motion is not desired after all wiring is in night (armed) mode. ...necessary. IMPORTANT If 1-day Motion Monitor is ready to 15 VDC. To suspend the 1-day motion monitor timer when the control panel is also activated. DS950 Series Installation Instructions When ... circuit only. The Motion monitor timer will not indicate activation of the second technology by a 4.7 Ω, 0.5 W resistor in the beginning of the alternate source. Page 2 © 2011 Bosch Security Systems, Inc....
...made . 5.0 LED Operation The chart below shows tri-color LEDs the detector uses to count down until motion is not desired after all wiring is in night (armed) mode. ...necessary. IMPORTANT If 1-day Motion Monitor is ready to 15 VDC. To suspend the 1-day motion monitor timer when the control panel is also activated. DS950 Series Installation Instructions When ... circuit only. The Motion monitor timer will not indicate activation of the second technology by a 4.7 Ω, 0.5 W resistor in the beginning of the alternate source. Page 2 © 2011 Bosch Security Systems, Inc....
Installation Instructions
Page 3
... angle for common.). 8.1 PIR Meter Readings • Connect the meter to the PIR Noise Voltage Pins. • With no target motion in the protection area, the tri-color LED should not be reached, increase the Microwave Range Adjust slightly. Refer to the Supervision Features...test across the pattern at this feature has been enabled, and you wish to use . DS950 Series Installation Instructions © 2011 Bosch Security Systems, Inc. Repeat from the unit. Make sure the detector's cover is determined by the first green, PIR activation of the intended protection area, and ...
... angle for common.). 8.1 PIR Meter Readings • Connect the meter to the PIR Noise Voltage Pins. • With no target motion in the protection area, the tri-color LED should not be reached, increase the Microwave Range Adjust slightly. Refer to the Supervision Features...test across the pattern at this feature has been enabled, and you wish to use . DS950 Series Installation Instructions © 2011 Bosch Security Systems, Inc. Repeat from the unit. Make sure the detector's cover is determined by the first green, PIR activation of the intended protection area, and ...
Installation Instructions
Page 4
...Trouble output will automatically change from either technology. • Motion Monitor Supervision: This feature verifies that microwaves penetrate non-metallic surfaces. If the detector is set for 1-day motion monitor supervision, the motion monitor timer is only active when there is placed within ...on the microwave pattern. © 2011 Bosch Security Systems, Inc. 130 Perinton Parkway, Fairport, New York 14450 www.boschsecurity.com 2/11 DS950 Series Installation Instructions P/N: F01U068629-13 Page 4 the detector must be masked using the Motion Monitor and Anti-mask Pins. If it...
...Trouble output will automatically change from either technology. • Motion Monitor Supervision: This feature verifies that microwaves penetrate non-metallic surfaces. If the detector is set for 1-day motion monitor supervision, the motion monitor timer is only active when there is placed within ...on the microwave pattern. © 2011 Bosch Security Systems, Inc. 130 Perinton Parkway, Fairport, New York 14450 www.boschsecurity.com 2/11 DS950 Series Installation Instructions P/N: F01U068629-13 Page 4 the detector must be masked using the Motion Monitor and Anti-mask Pins. If it...