Administration Guide
Page 25
...'s Guide for H.323 (version 3.0) 1-5 Figure 1-6 shows the rear panel of the applicable configuration, check your specific application. The Cisco ATA 186-I2 and Cisco ATA188-I2 provide 270 ohm + 750 ohm // 150-nF complex impedance. Figure 1-5 Cisco ATA 186-Rear View 72210 PHONE 1 PHONE 2 10BaseT ACT 5V RJ-11 FXS ports RJ-45 10BaseT Power connector...
...'s Guide for H.323 (version 3.0) 1-5 Figure 1-6 shows the rear panel of the applicable configuration, check your specific application. The Cisco ATA 186-I2 and Cisco ATA188-I2 provide 270 ohm + 750 ohm // 150-nF complex impedance. Figure 1-5 Cisco ATA 186-Rear View 72210 PHONE 1 PHONE 2 10BaseT ACT 5V RJ-11 FXS ports RJ-45 10BaseT Power connector...
Administration Guide
Page 164
...for the G.711 codecs do not appear in the Enable encoder and DPKT 1st debug lines. Debugging FAX Mode When the Cisco ATA is ATA186-I1, ATA186-I2, ATA188-I1, or ATA188-I2. • The fax relay option for H.323 (version 3.0) OL-4804-01 If the log shows proper NSE packet ...transaction and G.711 upspeed for the remote gateways has been disabled. Debugging the Cisco ATA 186/188 Fax Services Chapter 7 Configuring and Debugging ...
...for the G.711 codecs do not appear in the Enable encoder and DPKT 1st debug lines. Debugging FAX Mode When the Cisco ATA is ATA186-I1, ATA186-I2, ATA188-I1, or ATA188-I2. • The fax relay option for H.323 (version 3.0) OL-4804-01 If the log shows proper NSE packet ...transaction and G.711 upspeed for the remote gateways has been disabled. Debugging the Cisco ATA 186/188 Fax Services Chapter 7 Configuring and Debugging ...
Administration Guide
Page 205
..., network delay, and packet-loss rate. Enhanced fax pass-through and G.711 fax mode. Success of on the Cisco ATA. Appendix C Cisco ATA Specifications Ringing Characteristics Ringing Characteristics Table C-5 Ringing Characteristics Description Specification Tip/ring interfaces for H.323 (version 3.0) C-3... port terminating impedance option The Cisco ATA186-I1 and Cisco ATA188-I1 provide 600-ohm resistive impedance. The Cisco ATA186-I2 and Cisco ATA188-I2 provide 270 ohm + 750 ohm // 150-nF complex impedance. OL-4804-01 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor ...
..., network delay, and packet-loss rate. Enhanced fax pass-through and G.711 fax mode. Success of on the Cisco ATA. Appendix C Cisco ATA Specifications Ringing Characteristics Ringing Characteristics Table C-5 Ringing Characteristics Description Specification Tip/ring interfaces for H.323 (version 3.0) C-3... port terminating impedance option The Cisco ATA186-I1 and Cisco ATA188-I1 provide 600-ohm resistive impedance. The Cisco ATA186-I2 and Cisco ATA188-I2 provide 270 ohm + 750 ohm // 150-nF complex impedance. OL-4804-01 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor ...